Operating instructions
OPERATING INSTRUCTIONS
5. To be able to manually turn on the security light from
inside your home, toggle the wall light switch OFF and
ON within 2 seconds. The security light will turn on and
stay on for approximately 8 hours, or until the dusk-
to-dawn sensor detects light in the morning. Once the
dusk-to-dawn sensor detects light, the manual “ON”
mode will automatically go back to its original settings
of the AUTO motion sensor mode. At any point while in
manual “ON” mode, return to the AUTO motion sensor
mode by toggling the wall light switch OFF and ON
again within 2 seconds.
6. Once you have conrmed that the security light is
working properly, apply a small bead of silicone
caulking (not included) around the perimeter of the
rear housing cover to prevent water seepage into the
electrical compartment.
7. Press t the silicone caps (FF) into the mounting
screw openings to prevent water seepage into the
housing.
Hardware Used
Silicone Caps
x 2
FF
WARRANTY
The manufacturer warrants this lighting xture to be free from defects in materials and workmanship for a period
of (3) years from the date of original purchase by the consumer. We will repair or replace (at our option) the unit
in the original color and style if available, or in a similar color and style if the original item has been discontinued,
without charge. The manufacturer warrants the LEDs for 3 years, providing the xture is not used in a commercial
application where it is on 24 hours per day, but is used in a residential environment for 3 - 5 hours per day.
Defective units must be properly packed and returned to the manufacturer with a letter of explanation and your
original purchase receipt showing date of purchase. Call 1-866-994-4148 to obtain a return authorization number
and an address where to ship your defective product. Note: No C.O.D. shipments will be accepted. The liability of
the manufacturer is in any case limited to replacement of the defective light xture product. The manufacturer will
not be liable for any other loss, damage, or injury which is caused by the product. This limitation upon the liability
of the manufacturer includes any loss, damage, or injury which is (I) to person or property or otherwise; (II)
incidental or consequential in nature; (III) based upon theories of warranty, contract, negligence, strict liability,
tort, or otherwise; or (IV) directly, or indirectly
related to
the sale, use, or repair of the product. This warranty
gives you specic rights, and you may also have other rights which vary from state to state.
Printed in China
CARE AND MAINTENANCE
• Periodically clean the xture and diffuser using a mild, non-abrasive glass cleaner and soft cloth. Do NOT
use solvents or cleaners containing abrasive agents. When cleaning the xture, make sure you have the
power turned off and do not spray liquid cleaner directly onto any part of the xture or LEDs.
SECURITY LIGHT OPERATION
MODE SLIDE SWITCH WALL SWITCH SENSITIVITY A
Test Mode Test Turn on Any setting
AUTO Motion Sensor 1, 5, or 10 Minutes ON Any setting
Mode
Manual “ON” Mode 1, 5, or 10 Minutes Toggle OFF and ON Any setting
within 2 seconds
Return to AUTO Motion 1, 5, or 10 Minutes Toggle OFF and ON Any setting
Sensor Mode within 2 seconds
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION A
Light does not come on 1. No power is being 1. Check that circuit breaker and/or wall
at night when motion delivered to the xture. switch power is on.
is detected.
2. Another light source is 2. Turn off surrounding lights and/or re-aim
causing the security light the sensor head.
to think it is daylight.
3. Wiring inside electrical 3. AFTER turning power off to the xture,
came loose. reconnect any loose wiring.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION A
Security light comes 1. Dusk-to-dawn sensor is 1. Shine a ashlight onto the light sensor. If the
on during the day. a shaded area and is security light turns off then the xture is
fooled into thinking it mounted in an area that does not allow enough
is nighttime. light to enter the sensor. Relocate security light.
2. Dusk-to-dawn sensor 2. If under warranty, contact Customer Service.
is faulty.
Security light cycles ON 1. Dusk-to-dawn sensor is 1. Change position of light head aim light
and OFF continuously. sensing reected light away from the reecting surfaces.
from the security light.
2. Put a small piece of black electrical tape over
the Dusk-to-dawn sensor control.
3. Relocate security light to a different location
where it no longer causes reected light.
Security light comes 1. Light is sensing motion 1. Make sure the sensor is not picking up moving
on for no apparent in the detection zone. objects such as bushes, trees, trafc, water, etc.
reason at night.
2. Test the motion sensor by covering up the front
curved lens with cardboard to block the view. If
the light turns off then something in the
detection zone is triggering the sensor.
Reposition the motion sensor or change the
sensitivity (distance) of the sensor.
Lowes.com
FF
Utilitech & UT Design® are registered
trademarks of LF, LLC. All Rights Reserved.
6
7