Installation Guide

2
3
SAFETY INFORMATION
PREPARATION
Before beginning installation of product, make sure all parts are present. Compare parts with
package contents list and diagram above. If any part is missing or damaged, do not attempt to
assemble, install or operate the product.
Estimated Assembly Time: 15 minutes
Tools Required for Assembly (not included): Flathead screwdriver, Philips screwdriver, pliers,
wire cutters, safety glasses, step ladder
Helpful Tools (not included): Wire strippers
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install
the product.
1. WARNING: RISK OF SHOCK
House electrical current can cause painful shock or serious injury unless handled properly.
For your safety always remember to:
-Turn off the power supply at the fuse or circuit box before you install the fixture, change the
lamps or perform other maintenance.
-Ground the fixture to avoid potential electrical shocks and to ensure reliable starting.
-Double check all connections to be sure they are tight and correct.
-Wear rubber–soled shoes and work on a very sturdy wooden ladder.
*DO NOT USE THIS FIXTURE WITH A DIMMING CIRCUIT
-This fixture is designed for indoor use ONLY and should not be used in areas with limited
ventilation or high ambient temperatures.
-Remove the old fixture. Make yourself a sketch of how the fixture is wired (index the sketch by
wire color) or mark the wires themselves with masking tape and a pencil so you will know how to
correct the wires to your new fixture. If several wires are involved or if the wiring seems more
complicated and perhaps even includes a red wire, take note of the connections before
disconnecting them.
2. This fixture is designed for use in circuit protected by a fuse or circuit breaker. It is also
designed to be installed in accordance with local electrical codes. If you are unsure about your
wiring, consult a qualified electrician or local electrical inspector.
3. WARNING: RISK OF INJURY
Some metal parts in the fixture may have sharp edges. To prevent cuts and scrapes, wear gloves
when handing parts.
4. Account for small parts and destroy packing material as these may be hazardous to children.
5. CAUTION: RISK OF FIRE
Minimum 90℃ supply connection wires
SAVE THESE INSTRUCTIONS
DO NOT ATTEMPT TO ASSEMBLE THIS FIXTURE WHILE IT IS PLUGGED IN.
IMPORTANT: The installation of this fixture will require you to provide a means of holding the
fixture in place while final wiring is being done. If no means of support for the fixture can be
provided, the installation will require 2 people to install, one to hold the fixture up while another
person does the final wiring and securement.
P
ACKAGE CONTENTS
A Housing Assembly 1
B
Ballast
(preassembled to
Housing Assembly (A))
1
C
Lamp Clip
(preassembled to
Housing Assembly (A))
6
D
Diffuser Latch
(preassembled to
Housing Assembly (A))
3
2
1
E
F
Circline Lamp
Diffuser
(preassembled to
Housing Assembly (A))
PART DESCRIPTION QUANTITY
I
HARDWARE CONTENTS
Crossbar
DD
Short screw
AA
Qty. 2
Long screw
BB
Qty. 2
Wire nut
CC
Qty. 3
Qty. 1
Lowes.com/allenandroth
Lowes.com/allenandroth
F
A
D
C
B
E
6. WARNING: This product contains chemicals, including lead, known to the state of
California to cause birth defects and other reproductive harm. Wash hands after handling.
Hg
LAMP CONTAINS MERCURY
L’AMPOULE CONTIENT DU MERCURE
LA LAMPARA CONTIENE MERCURIO
Manage in accordace with Spills,Disposal and Site Cleanup Requirements.
In case of breakage follow clean-up procedures provided by contacts below.
Veuillez respecter les exigences en matiere de deversement,d’elimination et
de nettoyage.
En cas de bris,suivez les consignes de nettoyage fournies par les sources ci-dessous.
Manipule segun las exigencias sobre derrames,eliminacion y limpieza del lugar.
En caso que se rompa ,siga los procedimientos de limpieza proporcionados por los
siguientes contactos.
www.epa.gov/cflcleanup
1-866-284-4010
7.This device complies with Part 18 of the FCC Rules.