Installation Guide

ManualsBrandsUtilitech Pro ManualsLighting & Fans2.5-in Plug-In Under Cabinet LED Puck Light

ITEM/ARTICLE/ARTÍCULO #0406089

MODEL/MODÈLE/MODELO

#AC1012-WHG-03LF3-U

3 CT STARTER KIT

ENSEMBLE DE DÉPART DE 3 PIÈCES

KIT PARA EMPEZAR

DE 3 UNIDADES

PACKAGE CONTENTS/CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETE

HARDWARE CONTENTS/QUINCAILLERIE INCLUSE/ADITAMENTOS

SAFETY INFORMATION/CONSIGNES DE SÉCURITÉ/INFORMACIÓN DE SEGURIDAD

Cap Screw

Vis d'assemblage

Tornillo de tapa

Power Cord Mounting Clip

Dispositif de fixation des cordons d'alimentation

Sujetador de montaje para cables de alimentación

Mounting Screw

Vis de montage

Tornillo de montaje

Cord Mounting Clip

Dispositif de fixation des cordons

Sujetador de montaje para cables

ATTACH YOUR RECEIPT HERE

JOIGNEZ VOTRE REÇU ICI

ADJUNTE SU RECIBO AQUÍ

Serial Number/Numéro de série/

Número de serie

Purchase Date/Date d’achat/

Fecha de compra

Utilitech & UT Design

and Grounded in Quality

are registered

Utilitech le motif UT

et Grounded in Quality

sont des marques

Utilitech & UT Design® y Grounded in Quality® son marcas

Call customer service at 1-866-994-4148,

8 a.m. - 6 p.m., EST, Monday - Thursday,

8 a.m. - 5 p.m., EST, Friday.

Communiquez avec notre service à la clientèle

au 1 866 994-4148, entre 8 h et 18 h (HNE),

du lundi au jeudi, ou entre 8 h et 17 h (HNE) le

vendredi.

Llame a Servicio al Cliente al 1-866-994-4148

de 8 a.m. a 6 p.m. de lunes a jueves y de 8 a.m.

a 5 p.m. los viernes, hora estándar del Este.

Questions/Des questions/¿Preguntas?

Please read and understand this entire manual before attempting to assemble, operate or install the product. Save these instructions

in a location close to your light fixture so you can refer to them at a later time.

Assurez-vous de lire et de comprendre l’intégralité du présent manuel avant de tenter d’assembler, d’utiliser ou d’installer l’article.

Conservez ces instructions à proximité du luminaire afin de pouvoir les consulter ultérieurement.

Lea y comprenda completamente este manual antes de intentar ensamblar, usar o instalar el producto. Guarde estas instrucciones en

un lugar cercano a su lámpara, de esta manera podrá consultarlas posteriormente.

Note: Hardware shown actual size./Remarque : La quincaillerie est illustrée en grandeur réelle./

Nota: Los aditamentos se muestran en tamaño real.

Summary of content (6 pages)

PAGE 1
ITEM/ARTICLE/ARTÍCULO #0406089 3 CT STARTER KIT ENSEMBLE DE DÉPART DE 3 PIÈCES KIT PARA EMPEZAR Utilitech & UT Design and Grounded in Quality are registered trademarks of LF, LLC. All Rights Reserved. DE 3 UNIDADES Utilitech le motif UT et Grounded in Quality sont des marques ® ® ® ® de commerce déposées de LF, LLC. Tous droits réservés. Utilitech & UT Design® y Grounded in Quality® son marcas registradas de LF, LLC. Todos los derechos reservados.
PAGE 2
SAFETY INFORMATION/CONSIGNES DE SÉCURITÉ/INFORMACIÓN DE SEGURIDAD CAUTION/MISE EN GARDE/PRECAUCIÓN • DO NOT USE THIS FIXTURE WITH A DIMMING CIRCUIT. If you presently have dimmer controls, you will need to remove them and replace them with regular electrical switches. If you have a three-way dimmer, you will have to replace it with a regular three-way switch. If you are unfamiliar with electrical installations, it is recommended you have a qualified electrician do your installation.
PAGE 3
ASSEMBLY INSTRUCTIONS/INSTRUCTIONS POUR L’ASSEMBLAGE/NSTRUCCIONES DE ENSAMBLAJE The dimmer control unit (A) and the 3 puck lights (B) are all connected on one continuous cord. Therefore some planning will be required prior to installation. Before installing your puck light kit, place the dimmer control unit (A) and puck lights (B) on a clean surface and adjusting the cord length to simulate spacing.
PAGE 4
ASSEMBLY INSTRUCTIONS/INSTRUCTIONS POUR L’ASSEMBLAGE/NSTRUCCIONES DE ENSAMBLAJE 4. Hold the dimmer control unit (A) 4 against the mounting surface and mark the locations for the mounting screws (DD). Dimple the surface with either an awl, a nail, or drill a small pilot hole for the mounting screws (DD). Fasten the dimmer control unit to the cabinet with two A mounting screws (DD). NOTE: Let the cords hang freely and do not fasten them into place during this part of the installation.
PAGE 5
ASSEMBLY INSTRUCTIONS/INSTRUCTIONS POUR L’ASSEMBLAGE/NSTRUCCIONES DE ENSAMBLAJE 6. Any excess cords can be secured 6 using the cord mounting clips (BB). Use caution when attaching the cord mounting clips (BB) to the cabinet to ensure that the metal nail does not pierce the cord. BB Vous devez fixer l’excédent des cordons qui pend à l’aide des dispositifs de fixation des cordons (BB).
PAGE 6
CARE AND MAINTENANCE/ENTRETIEN/CUIDADO Y MANTENIMIENTO • You may want to periodically clean the fixture using a mild, non-abrasive glass cleaner and soft cloth. Do NOT use solvents or cleaners containing abrasive agents. When cleaning the fixture, make sure you have the power turned off and do not spray liquid cleaner directly onto the fixture, connection sockets, linking cord plug or switch.