LEAPERS , INC.
MUO012041311 UTG RANGE ESTIMATING SCOPES RETICLE INTENSIFIED SCOPES TOTAL SOLUTION TO YOUR NEEDS -COMMITMENT TO BEST QUALITY, BEST VALUE AND BEST SERVICEwww.LEAPERS.com 32700 Capitol Street, Livonia, MI 48150, U.S.A. Tel:(734)542-1500 Fax:(734)542-7095 Email:office@leapers.
MODEL NO.: SCP-DS3068W red/green dots TactEdge® Angled Integral Sunshade 1 Lockable Elevation Adjustment Knob Lockable Windage Adjustment Knob Illumination Adjustment Knob One Piece Quick Detach Picatinny/Weaver Mount Pat.
2 MODEL NO.: SCP-DS3840W Lockable Windage Adjustment Knob Riser Lockable Elevation Adjustment Knob TactEdge® Angled Integral Sunshade Vertical Low Profile QD Picatinny Mount Pat.
3 MODEL NO.: SCP-DS3039W Lockable Windage Adjustment Knob Riser Lockable Elevation Adjustment Knob Illumination Adjustment Knob Vertical Low Profile QD Picatinny Mount Pat.
4 MODEL NO.: SCP-DS3028W Lockable Elevation Adjustment Knob Illumination Adjustment Knob Lockable Windage Adjustment Knob Low Profile Integral Quick Detach Picatinny/Weaver Mount Pat.
5 MODEL NO.: SCP-DS3026W Elevation Adjustment Knob Illumination Adjustment Knob Low Profile Quick Detach Picatinny/Weaver Mount Pat.
6 MODEL NO.: SCP-RG40CDQ SCP-RG40SDQ Illumination Adjustment Knob Elevation Adjustment Knob Low Profile Integral Quick Detach Picatinny/ Weaver Mount Pat.
7 MODEL NO.
8 A. Install QD Mount with Riser: (for SCP-DS3840W and SCP-DS3039W only) This configuration offers many different options from the bi-directional mounting feature for both the QD mount and the riser. The riser can be installed in either direction depending on your preference. The same for the QD mount. (NOTE: Figures included only show one example direction.) Locate four screws and install a spring washer and a flat washer onto each screw. I.
II. Install QD Mount: Based on your eye relief preference, select two holes on the QD mount and align them to the mating holes on the extruded part of the riser. Install and fasten the remaining two screws to fully secure the mount as shown in Fig 1. B1. Install the Dot Sight onto the Rifle: ( for Dot Sights with QD Mounts ) 1. Hold the rifle in your natural shooting position. Place the scope onto the Picatinny rail on the rifle to estimate the best position for your shooting preference.
Turn the Cam Lever toward its unlocked position as shown in Fig 2. Place the QD mount on the Picatinny Rail at the desired position. Make sure to seat the cross bolt into a selected slot. Note: For SCP-DS3068W, turn the locking levers toward opposite directions to unlock as shown in Fig 3. 3. k Fig 2 oc To un-lock To u n - l k 10 To 4.
5. Use the included Allen wrench to adjust the Hex Screw at the side of the cam for proper tension and fit against the rail. Adjust clockwise to increase the tension and tighten the clamping width. Adjust counter-clockwise to decrease the tension and increase the clamping width. 6. The optimal tension is achieved when the side plate first makes contact with the Picatinny rail while the Cam Lever still has enough travel left for you to securely snap into its locking position.
12 B2. Install the Dot Sight onto the Rifle: ( for Dot Sights with Locking Nuts ) 1. Place the mounting deck onto the rail. 2. Adjust the mounting deck position until you are satisified with the view. 3. Tighten each locking nut with a screwdriver or coin as shown in Fig. 4. Fig 4 C. Install Battery: 1. 2. 3. The battery is housed inside the Red/Green Illumination Rheostat. Fig.5 and Fig.6 show where the battery compartment is on 2 representative configurations.
4. 5. Remove the battery (if there is one) and install a new one with + side(anode) facing out. Replace the cap and screw it clockwise to tighten. 13 D. On/Off Switch and Brightness Adjustment: 1. Dial the rheostat to turn on the illumination. 2. For SCP-RD40RGW-A, the white dot on the left side of the sight indicates the current setting as shown in Fig. 7. When the Current Setting is “R” or “G”, the unit is off. 3. Red/Green colored coded numbers(Fig. 7) or the red/ green band (Fig.
14 E. Zero the Dot Sight: Note: Leapers dot sight comes with three different adjustment turrets as shown below: Double Lock Turret (2 locking screws) Zero Deadlock Turret No Additional Lock Turret ( 1 locking screws) The purpose of zeroing the dot sight is to ensure that the illuminated dot is aligned with the impact point of your rifle. Before zeroing, read the following adjustment knob instruction carefully. 1. Unscrew and remove the cap of the adjustment knob. 2.
WARNING FOR DOUBLE LOCK TURRETS: DO NOT over-loosen the locking screws! It may cause the face cover to fall off if screws are backed out too far. If, by mistake, the face lid fell off when you are looseing the screws, please follow instructions below to replace the face cover. 3. A. Lock both screws down, making sure that they are flush with the surface. B. Apply a little loctite or similar adhesive on the flat surface of the knob.
For Zero Deaklock Turrets, use a flat head screwdriver to adjust the Fig 10 windage and elevation as shown in Fig. 10. Refer to the ZEROING section for further steps. 16 II. 4. OPTIONAL ZERO LOCKING – Once the scope is zeroed, you can use the Allen wrench to lock down the turrets for most repeatable shooting performance. Fig 11 I. To lock Double Lock Turrets: Use the included small Allen wrench to fully lock down both screws by turning them clockwise as shown in Fig. 11.
II. 5. To lock Zero Deadlock Turrets: Use the 17 included small Allen wrench to fully lock down the screw by turning it clockwise as shown in Fig. 12. ZEROING - Make sure to un-lock turrets before performing this step. I. Zeroing with a Bore Sighter A. When the turret is ready for adjustment, you will able to dial and have a clear audible click. B. Follow the instruction of your bore sighter and install it in the muzzle of your rifle, lining it with the dot sight as closely as possible. C.
windage until the crosshair matches the bore sighter. 18 II. Zeroing on a Target A. Place a target 100 yards away (35 yards for air gun). B. Use a steadying device such as a shooting stand or bipod, set the illumination to your prefer settings, aim at the center of the target and fire a test group shot, if safe to do so. C. If the impact point of the test shot is exactly in the center of the target then the dot sight is zeroed.
E. Now the dot sight should be zeroed. Make sure to lock both elevation and windage knobs. 19 F. Different Dot Sight Reticles: Note: Depending on your models, your dot sight may come with one of the following reticles: Circle Dot Reticle Specs Illustration Single Dot Reticle Dot size: about 4 MOA Dot size: about 4 MOA Circle Dia.
G. Care and Maintenance: 20 1. Take care not to drop or knock the dot sight once it is zeroed. 2. Maintain the metal surface of the dot sight by removing any dirt or sand with a soft brush so as to avoid scratching the finish. 3. Wipe the lens with a clean flannel cloth to keep it clean and dry. In order to avoid scratching the glass, ensure both the lens and cloth are clean. Do not use finger or finger nail to touch/clean lenses. 4. Store the dot sight in a cool dry place when not in use.
H. Two Year Manufacturer’s Warranty 21 Warranty against material or workmanship defects applies based on the following conditions 1. Product is a first-hand purchase. Evidence of purchase is required for warranty service. Warranty is not transferrable. 2. Product is not disassembled, parts/ screws not removed or loosened, and the product is not tampered with in any way. Any evidence of such interference will void the warranty. 3.
17 re o l Exp e r Mo At 32700 Capitol Street, Livonia, MI 48150, U.S.A. Tel:(734)542-1500 Fax:(734)542-7095 Email:office@leapers.
