Operating Instructions

14 15
F. ADJUSTING EYEPIECE DIOPTER
(Eye Piece Adjustment)
Diopter adjustment provides additional
focus adjustment to adapt the scope to
your eyesight.
1. Diopter adjustment ring is located at
the ocular end of the scope. Point
the scope at an uncluttered and light
colored background object, such as a
white wall. Look through the scope and
turn the dial ring clockwise or counter-
clockwise until the reticle looks the
sharpest to you at rst glance.
2. Note: Different individuals will have a different eye focus which will
result in a different diopter setting. A person will use different diopter
settings with or without eye glasses.
1. The battery is housed inside the Red/Green Illumination Rheostat.
2. With one hand, rmly hold the Rheostat’s housing in place while
simultaneously unscrewing the battery cap with your other hand.
3. Place the battery within the Illumination Rheostat housing with the +
side facing upward.
4. Screw the battery cap back on until tight using the same method in
Step 2.
G-1. EZ-TAP G-2. Side Rheostat
G. installing battery
(For Recle Intensied Models Only)
H. adjusting Reticle Illumination
(For Recle Intensied Models Only)
Operating in Multi-Color Mode
1. Press the R button to change the color between
the selections in the Color Index Table.
2. Press the G button to change the color intensity
as shown in the Color Index Table.
Operating in the RGB Mode
1. Press the R button to turn the red light on or
to change brightness of the red light.
2. Press the G button to turn the green light on
or to change brightness of the green light.
Turn On/Off
1. Press either the G or R button to turn on
the light.
2. Press and hold either the G or R button
for 1 second to turn off the light.
3. Light will go off after 1 hour with no action.
G R
G OR R
G R
G OR R
G R
G OR R
Color Index Table
Magenta Thistle Plum Violet Orchid Purple
Pink
Rosy
Brown
Coral Crimson Brown Maroon
Yellow Khaki Orange
Golden
Rod
Chocolate Olive
Law
Green
Plain
Green
Spring
Green
Olive
Drab
Sea
Green
Forest
Green
Cyan Azure Turquoise
Cadet
Blue
Dark
Cyan
Teal
Blue Sky Blue
Dodger
Blue
Indigo
Midnight
Blue
Navy
Color
Intensity
G Button
R Button
36
FULL
IE
COLORS
H-1.
Color Coded/Numbered
Rheostat
H-2.
Color Coded/Fine
Adjustment Rheostat
H-3.
EZ-TAP
®
Console
H-1 and H-2 Illumination Adjustment
Dial the Rheostat to turn on the illumination and verify its color and
brightness at each position.
H-3 Illumination Adjustment (IE
®
Models)
Memory Feature
When turned on, H-3 illuminated reticle shows the same color and
brightness you last used.
Switching between RGB and Multi-Color Modes
1. The default mode is the RGB mode.
2. To switch between the RGB mode and the
Multi-Color mode, press and hold BOTH G & R
buttons at the same time for 1 second.
G R
G AND R
1. For variable power scopes, there
is a power ring in front of the
eyepiece assembly. To change
magnication, turn the ring to align
the desired number on the ring with
the index dot on the main tube.
2. The lower power provides wider
eld of view for quick aiming at
close range. The higher power
is for precise long-range aiming.
When the numbers on the ring
are not visible under low light
condition, turn the ring left to
increase the power, turn the ring
right to decrease the power.
3. Note: Never loosen the screw
in the power ring. Doing so will
break the sealed state of the scope
and destroy the fogproof feature.
The power ring should not be
disassembled.Do not try to lubricate it.
Any such action will void the warranty.
I-1. Adjusting Power Ring
I. Adjusting Magnification
(For Variable Power Models Only)
I-2. Power Ring Screw