LEAPERS , INC. ® OPTICS Complete Installation and Operating Instructions w w w. l e a p e r s .
Leapers Inc. Index ® Proudly Presents UTG OPTICS TOTAL SOLUTIONS FOR ALL YOUR HUNTING AND SHOOTING NEEDS Innovation, Quality, Value, and Service A. Scope Parts Illustration 4 B. Major Features 7 C. Mounting the Scope Ring 8 D. Installing the Scope 9 E. Understanding the Reticle 10 F. Adjusting Eyepiece Diopter 14 G. Installing Battery 14 H. Adjusting Reticle Illumination 14 I. Adjusting Magnification 15 J. Adjusting Parallax 16 K. Zeroing 16 L.
4 5 a. scope parts illustration 01 ! 02 03 WARNING: 04 Read entire manual before mounting your scope. Make sure the firearm is not loaded upon installation.
6 7 ACCESSORIES Optional - 3” Sunshade (for 50mm Obj. Dia. Models) Optional - 2.5” Sunshade (for 40mm Obj. Dia. Models) Optional - 2” Sunshade (for 32mm Obj. Dia. Models) Mounting Rings (Not all models include rings. Appearance may vary.) Allen Wrench (One or multiple are included. Size may vary.) b.
8 C-2., C-3. Mounting Twist Lock and Thumb Nut Locking Scope Rings c. Mounting the Scope Ring Locking Holes CAUTION: Make sure firearm is not loaded. Remove magazine (if applicable) and examine chamber. Use safe handling procedures at all times. C-1. QD Lever Lock Scope Rings C-2. Twist Lock Scope Rings 9 1. Turn the Twist Lock or Thumb Nut counterclockwise to widen the locking plate and provide the needed mounting clearance to evenly seat onto the Picatinny Rail. 2.
10 1 5 3 the Mil-dot reticle with 9 dots in each direction, including the counting of the 2 inner tips of the opposite crosshairs, that amounts to 21 available aiming points. 7 11 E-2. PRO 4-STEP RETICLE: 6 2 8 Designed for the discriminating crossbow shooters, the new etched glass Pro 4-step reticle comes with 3 horizontal lines and 4 floating points. Only the floating points are illuminated.
12 background, while the thin crosshairs are for precise aiming and better view of the area of interest on the target. Duplex reticle could be etched on glass or etched from metal thin film. Accordingly, the center crosshair may be floating or connected to the outer bars. Zeroing the Pro 4-Step Reticle: Follow the steps below to zero a scope with Pro 4-step Reticle on a crossbow: First of all, adjust the speed dial ring on the scope to match the speed of your crossbow (275 to 385 feet per second).
14 G F. ADJUSTING EYEPIECE DIOPTER (Eye Piece Adjustment) R G OR R Diopter adjustment provides additional focus adjustment to adapt the scope to your eyesight. G 1. Diopter adjustment ring is located at the ocular end of the scope. Point the scope at an uncluttered and light colored background object, such as a white wall. Look through the scope and turn the dial ring clockwise or counterclockwise until the reticle looks the sharpest to you at first glance. R G OR R G 2.
16 J. adjusting Parallax K-1. Sniper W/E Operation (For Models with Adjustable Objective Only) J-1. Front AO Adjustment 1. 2. 3. J-2. Side Wheel Adjustable Turret (SWAT AO) J-3. SWAT AO Big Wheel (Optional) Find the proper type of dial from the images above. Aim the scope at your target.
18 Zero Resetting Screw 19 K-2. High Tower Zero Lockable/Resettable Turret Zero Locking Ring 4. Remove your bore sighter and confirm your zero with a live fire test group if safe to do so. 5. If the point of impact (POI) of the test group is exactly in the center of the target then the POI is POA and the scope is zeroed. 6. If the POI is not POA, further adjustments need to be made.
K-3. TF2+ Tool Free W/E Operation 20 Pull up To Unlock Adjustment Stage Lock Down Stage Push Down To Lock 1. The Windage and Elevation Adjustment Knobs have a unique 2-stage Tool-free design. The windage/elevation knobs are in the “locked” mode on a new scope out of the factory. Pulling the knobs upward allows for windage/elevation adjustment. 2. ZERO LOCKING (The windage/elevation knobs are in the LOCKED position for a new scope out of the factory.
22 1. K-7. Lockable W/E Operation The Windage and Elevation Adjustment Target Knobs have a unique Locking Screw design. An Allen Wrench is provided with the scope for adjustment. WARNING: DO NOT over-loosen the locking screws! It may cause the face cover to fall off if screws are backed out too far. If, by mistake, the face lid fell off when you were loosening the screws, please follow instructions below to replace the face cover. A.
24 e r o l p Ex More At , Inc., Leapers in artered headqu s h ., .A a an, U.S Michig s s e in the bus been in , g n ti o o lying sh of supp r o o td u and o hunting e W . 2 9 ce 19 gear sin d e is m ompro set un-c r fo s rd a nd om high sta p e r s .c ss e in s u w.l e a rb u w o f w o all ur goal ons. O operati total vide a is to pro f y line o n for an solutio ffer.