User's Manual

All Rights Reserved. 2 P/N 3102241 – Rev. EN03 – Jan 05, 2015
2. Mounting Guideline
This product is a member of a reliable, high-quality product family
using the latest technology available. Review the information in this
section to ensure you get the most out of the product. The information
in this User Guide is in accordance with NFPA 72.
Note A: Maximum coverage established by U.L. is based on providing
equal response time as sprinkler devices spaced at 10 ft. intervals (100
sq. /ft.) on a smooth ceiling approximately 15 feet high. Higher ceilings
may adversely affect response time and earlier response time may be
obtained by reducing the spacing between alarms.
Note B: Maximum distance is from any wall or ceiling projection
extending down more than 12 inches.
Pre-installation Considerations
Install the smoke alarm in accordance with NFPA Standard 72,
Chapters 17 and 29. Depending on the application, you may need to
reference other chapters of NFPA 72 or NFPA 101.
Choosing an Installation Location
When choosing an installation location, consider:
o Use of structure and type of construction
o Contents you want to protect and their burning characteristics
o Human occupancy
o Total area to be monitored
o Ceiling height and surface condition
o Air movement and vent locations
o Obstructions
o Deflections
After considering these factors, choose a location:
o The most favorable mounting location for a Heat Detector is on
the ceiling in the center of the room. At this location the alarm is
closest to all areas of the room.
EXCEPTION: When the mounting
surface might become considerably warmer or cooler than the
room, such as a poorly insulated ceiling, below an unfinished
attic or an exterior wall. In these cases the alarm should be
mounted on an inside wall.
o In areas where the ambient temperatures normally remain
between -10
°F (-23°C) and 100°F (38°C).
Away from ventilation sources, near ceiling fans, or other high air flow
areas that can prevent heat from reaching the Heat Detector.
The product shall be located on the ceiling no closer than 4 in.(102 mm)
from the sidewall or, if on a sidewall, mount between 4 (102 mm) and
12 in. (300 mm) from the ceiling.
In rooms with sloped or peaked ceilings, place alarms 3 feet (910 mm)
down or away from the highest point of the ceiling.
If mounting to suspended ceiling tile, secure the tile with the
appropriate fastener to prevent tile removal.
Heat Detectors are not to be used with alarm guards unless the
combination has been evaluated and found suitable for that purpose.
Note: A Heat Detector does not provide warnings for fires resulting
from explosions, smoking in bed, or other furniture; ignition of
flammable liquids, vapors, and gasses; and children playing with
matches or lighters.
Locations to Avoid
o Areas where normal ambient temperature exceeds products
operating temperature range.
o On the ceiling in rooms next to kitchens, where there is no
transom between the kitchen and such rooms.
o In areas with high humidity, like bathrooms/shower rooms or
areas near dishwashers or washing machines. Install at least
10 feet (3 m) away from these areas if possible.
o Near fresh-air inlets or returns or very drafty areas.
o Near heating/air conditioning vents, fans, and fresh air intakes,
which can drive heat away from the alarm.
o In dead-air spaces at the top of peaked ceilings or in corners
where walls and ceiling meet. Dead air can prevent heat from
reaching a Heat Detector.
o Within 10 feet (3 m) of fluorescent light fixtures or within 12 in
(300 mm) of a light fitting.
o Not suitable for outdoor use.
WARNING! LIMITATIONS OF HEAT DETECTORS
Wireless Heat Detectors are very reliable, but may not work under all
conditions. No fire alarm provides total protection of life or property.
Heat Detectors require a source of power to work.
This Heat Detector will not operate and the alarm will not sound if
batteries are dead or not installed properly.
Heat Detectors may not be heard. A sound sleeper or someone who
has taken drugs or alcohol may not awaken if the alarm is installed
outside a bedroom. Closed or partially closed doors and distance can
block sound. This alarm is not designed for the hearing impaired.
Alarms may not always activate and provide warning early
enough. Heat Detectors only activate when it has exceeded the rate of
rise or fixed temperature rating. If a fire starts in a chimney, wall, roof,
on the other side of closed doors, or on a different level of the property,
enough heat may not reach the alarm for it to alarm.
Alarms are a significant help in reducing loss, injury and even death.
However, no matter how good a detection device is, nothing works
perfectly under every circumstance and we must warn you that you
cannot expect an alarm to ensure that you will never suffer any
damage or injury.
Current studies have shown alarms may not awaken all sleeping
individuals. It is the responsibility of individuals in the household that
are capable of assisting others to provide assistance to those who may
not be awakened by the alarm sound, or to those who may be
incapable of safely evacuating the area unassisted.
3. Mounting the Sensor
Note: Add the product to the Control Panel before physically mounting
the alarm in the desired location.
A. Disconnect alarm-notification appliances, service-release devices,
and extinguishing systems. Test communications between the
control panel and alarm before permanently mounting the alarm
as follows:
− Hold the alarm where you plan to install it.
− Press the alarm test button for 8-to-10 seconds. The alarm
sends a signal to the control panel.