Installation Manual
Table Of Contents
- Sentrol AP750W Wireless PIR Motion Sensor
- Product Summary
- Installation
- Mounting the Motion Sensor
- Setting the Sensor Coverage Area and Sensitivity
- Walk Testing
- Installing Masks
- Programming
- 1. Put the panel into program mode.
- 2. Advance to the learn sensors menu.
- 3. Enter the appropriate sensor group and desired sensor number.
- 4. When the panel prompts you to trip the sensor, activate the sensor tamper switch by removing the sensor cover.
- 5. Reattach the sensor cover.
- 6. Exit from program mode.
- Final Testing
- 1. After the sensor has been mounted, remove the sensor cover to trip the tamper switch and acti vate the walk test mode.
- 2. Replace the sensor cover.
- 3. Place the control panel in test mode.
- 4. Move across the detection pattern until the sensor LED turns on, then STOP your motion.
- 5. Listen for the appropriate system response. If the system does not respond, proceed to the “Troubleshooting” section.
- Maintenance
- Replacing Batteries
- Note Avoid touching the mirror. Fingerprints may affect detection coverage
- 4. Carefully remove the PIR (lower) circuit board by pressing outward on either side tab, then pull up on the circuit board (see Figure 12).
- 5. Remove the PIR circuit board battery (located on opposite side of components) and install a new one, observing polarity (marked on the circuit board).
- 6. Re-install the PIR circuit board into the sensor plastic.
- 7. Re-install the transmitter circuit board onto the PIR circuit board.
- 8. Install a new battery in the transmitter circuit board, observing polarity (marked in battery bucket).
- Lithium Battery Disposal
- Troubleshooting
- Specifications
- Notices
- These devices comply with part 15 of the FCC rules. Operation is subject to the following two conditions:
- 1. These devices may not cause harmful interference.
- 2. These devices must accept any interference received, including interference that may cause undesired operation.
- Changes or modifications not expressly approved by Interactive Technologies, Inc. can void the users’ authority to operate the equipment.
- FCC ID: B4Z-844-PIR
- U.S. Patent Nos: 4,855,713, 4,864,636, 5,761,206, 5,805,063, 5,872,512, and 5,942,981
- Preliminary 9/1/04
5Sentrol AP750W Wireless PIR Motion Sensor Installation Instructions
Preliminary 9/1/04
Programming The following describes the basic steps for adding (learning) the sensor into panel memory. Refer
to the specific panel installation instructions for complete programming information.
1. Put the panel into program mode.
2. Advance to the learn sensors menu.
3. Enter the appropriate sensor group and desired sensor number.
4. When the panel prompts you to trip the sensor, activate the sensor tamper switch by removing
the sensor cover.
5. Reattach the sensor cover.
6. Exit from program mode.
Final Testing Final testing should be done to verify radio signal integrity and confirm control panel program-
ming and response. The actual transmitter range can be determined by performing a sensor test as
described below. Refer to the specific panel installation instructions for complete sensor testing
information.
1. After the sensor has been mounted, remove the sensor cover to trip the tamper switch and acti-
vate the walk test mode.
2. Replace the sensor cover.
3. Place the control panel in test mode.
4. Move across the detection pattern until the sensor LED turns on, then STOP your motion.
5. Listen for the appropriate system response. If the system does not respond, proceed to the
“Troubleshooting” section.
Maintenance At least once a year, the sensor should be tested to verify correct operation. The end user should
be instructed to put the sensor in walk test mode and walk through the far end of the coverage pat-
tern to verify proper detection.
Replacing Batteries
When battery replacement is necessary, observe proper polarity (positive +, negative -) when
installing the new batteries, or the sensor may be damaged.
Use only exact replacement 3-volt lithium batteries (CR123A).
You must be free of static electricity before handling circuit boards. Wear a
grounding strap or touch a bare metal surface to discharge static electricity.
Static
1. Remove the sensor cover (see Figures 4 and 5) and set it aside.
2. Remove the transmitter (upper) circuit board battery (see Figure 10)
3. Remove the transmitter circuit board and place it inside the cover (see Figure 11)
T R A N S M I T T E R
B O A R D
P U L L O U T O N
E I T H E R T A B
W H I L E P U L L I N G
T R A N S M I T T E R
B O A R D U P .
Figure 10. Removing the Transmitter Battery
Figure 11. Removing the Transmitter Circuit Boar
d