User's Manual
Table Of Contents
- Water Resistant Personal Help Button
- Product Summary
- Assembly Guidelines
- Assembly Options
- Wall Mount
- Belt Clip
- Wrist Bands
- 1. Lay the hook and latch wrist band across the back of the help button.
- 2. Compress the spring-loaded pins with a small screw driver
- 3. Slip the pins over the wrist band and into the pin slots located on the back of the help button.
- 1. Insert the spring-loaded pins through the ends of the plastic wrist band.
- 2. Compress the spring-loaded pins with a small screw driver.
- 3. Slip into the pin slots located on the back of the help button.
- Pendant
- 1. Make sure the necklace or chain fits through the larger hole in the pin-mounted necklace adapter.
- 2. Remove one of the spring-loaded pins from the plastic wrist band and insert it into the smaller hole on the necklace adapter.
- 3. Compress the spring-loaded pins with a small screw driver and slip them into the pin slots located on the back of the help button.
- 1. Slip the rope necklace into the top slot on the pendant adapter and hook the plastic ends together.
- 2. Snap the help button onto the four snap-on posts on the pendant adapter.
- Programming
- Testing the Help Button
- 1. Set the system to the Dealer Sensor Test mode.
- 2. Activate the help button by grasping the help button in your hand pressing it with your thumb or finger until the light blinks.
- 3. Listen for beeps sounded from system sirens. You should hear at least 7 beeps.
- 4. Test the help button from several locations within the premises to check for consistent response.
- 5. Instruct the user to test the help button weekly.
- Repair of the Help Button
- 1. Disassemble the help button by removing the four screws on the back of the help button and separate the cover and base.
- 2. Remove the old battery from its holder and install the new battery, observing polarity.
- 3. Reassemble the help button. Make sure to line up the LED indicator bump on the cover with the LED on the PCB.
- 4. Test the help button as described in “Testing the Help Button” section.
- 1. Disassemble the help button by removing the four screws on the back of the help button and separate the cover and base.
- 2. Reassemble the help button using the new cover. Make sure to line up the LED indicator bump on the cover with the LED on the PCB.
- Lithium Battery Disposal
- Specifications
- Notices
4
Specifications
Model No.: 60-609-95, 60-609-95R
RF Frequency: 319.5 MHz
Compatibility: All GE Security 319.5 MHz Control Panels/
Receivers
Battery Type: 3.0 VDC Lithium
Recommended Battery: Duracell (DL2032), Panasonic or Varta
(CR2032)
Typical Standby Current (µA): < 1
Estimated Battery Life (at 20° C): 4 years
Supervisory Interval: 64 minutes
Typical RF Output Power (mW): .25
Operating Temperature Range: 32° to 120° F (0° to 49° C)
Storage Temperature Range: -30° to 140° F (-34° to 60° C)
Relative Humidity: 5 - 90% non-condensing
Dimensions (inches): 1.5 x 1.3 x .5 (L x W x D) w/o adapters or
wrist bands
Weight (lb): .026
Notices
7KLVGHYLFHFRPSOLHVZLWK)&&5XOHV3DUW2SHUDWLRQLVVXEMHFWWR
WKHIROORZLQJWZRFRQGLWLRQV
7KLVGHYLFHPD\QRWFDXVHKDUPIXOLQWHUIHUHQFH
7KLVGHYLFHPXVWDFFHSWDQ\LQWHUIHUHQFHWKDWPD\EHUHFHLYHG
LQFOXGLQJLQWHUIHUHQFHWKDWPD\FDXVHXQGHVLUHGRSHUDWLRQ
&KDQJHVRUPRGLILFDWLRQVQRWH[SUHVVO\DSSURYHGE\*(,QWHUORJL[
FDQYRLGWKHXVHU·VDXWKRULW\WRRSHUDWHWKHHTXLSPHQW
)&&,'%=$3$1,&ORFDWHGRQEDFNRIGHYLFH
863DWHQWVDQGRWKHUVSHQGLQJ
5HG)R[5RDG$UGHQ+LOOV01
86$&DQDGD7HFKQLFDO6XSSRUW
*(6HFXULW\,QF$OOQDPHVDUHWUDGHPDUNVRIWKHLURZQHUV$OOULJKWVUHVHUYHG
)
*(6HFXULW\