User's Manual
Table Of Contents
- Water Resistant Personal Help Button
- Product Summary
- Assembly Guidelines
- Assembly Options
- Wall Mount
- Belt Clip
- Wrist Bands
- 1. Lay the hook and latch wrist band across the back of the help button.
- 2. Compress the spring-loaded pins with a small screw driver
- 3. Slip the pins over the wrist band and into the pin slots located on the back of the help button.
- 1. Insert the spring-loaded pins through the ends of the plastic wrist band.
- 2. Compress the spring-loaded pins with a small screw driver.
- 3. Slip into the pin slots located on the back of the help button.
- Pendant
- 1. Make sure the necklace or chain fits through the larger hole in the pin-mounted necklace adapter.
- 2. Remove one of the spring-loaded pins from the plastic wrist band and insert it into the smaller hole on the necklace adapter.
- 3. Compress the spring-loaded pins with a small screw driver and slip them into the pin slots located on the back of the help button.
- 1. Slip the rope necklace into the top slot on the pendant adapter and hook the plastic ends together.
- 2. Snap the help button onto the four snap-on posts on the pendant adapter.
- Programming
- Testing the Help Button
- 1. Set the system to the Dealer Sensor Test mode.
- 2. Activate the help button by grasping the help button in your hand pressing it with your thumb or finger until the light blinks.
- 3. Listen for beeps sounded from system sirens. You should hear at least 7 beeps.
- 4. Test the help button from several locations within the premises to check for consistent response.
- 5. Instruct the user to test the help button weekly.
- Repair of the Help Button
- 1. Disassemble the help button by removing the four screws on the back of the help button and separate the cover and base.
- 2. Remove the old battery from its holder and install the new battery, observing polarity.
- 3. Reassemble the help button. Make sure to line up the LED indicator bump on the cover with the LED on the PCB.
- 4. Test the help button as described in “Testing the Help Button” section.
- 1. Disassemble the help button by removing the four screws on the back of the help button and separate the cover and base.
- 2. Reassemble the help button using the new cover. Make sure to line up the LED indicator bump on the cover with the LED on the PCB.
- Lithium Battery Disposal
- Specifications
- Notices
2
To use the plastic wrist band
1. Insert the spring-loaded pins through the ends of the
plastic wrist band.
2. Compress the spring-loaded pins with a small screw-
driver.
3. Slip into the pin slots located on the back of the help
button.
Note
The plastic wrist band or almost any other 18 mm watch
band can be used.
Pendant
The help button can be worn as a pendant two different
ways:
• With a necklace using the pin-mounted necklace
adapter
• With the included rope necklace using the snap-on
pendant adapter.
To use the pin-mounted necklace adapter:
1. Make sure the necklace or chain fits through the larger
hole in the pin-mounted necklace adapter.
2. Remove one of the spring-loaded pins from the plastic
wrist band and insert it into the smaller hole on the
necklace adapter.
3. Compress the spring-loaded pins with a small screw-
driver and slip them into the pin slots located on the
back of the help button.
To use the pendant adapter:
1. Slip the rope necklace into the top slot on the pendant
adapter and hook the plastic ends together.
2. Snap the help button onto the four snap-on posts on
the pendant adapter.
Programming
This section describes the basic steps for adding the help
button to panel memory. For complete instructions, refer
to the specific panel Installation Instructions.
1. Set the panel in the program mode.
2. Enter the appropriate group number when prompted
by the panel.
3. Select the desired sensor number when prompted by
the panel.
4. When prompted by the panel to trip the sensor, press
the help button until the light blinks.
5. Exit from program mode.
Testing the Help Button
This section describes the basic steps for testing the help
button. For complete instructions, refer to the specific
panel Installation Instructions.
1. Set the system to the Dealer Sensor Test mode.
2. Activate the help button by grasping the help button in
your hand pressing it with your thumb or finger until
the light blinks.
3. Listen for beeps sounded from system sirens. You
should hear at least 7 beeps.
4. Test the help button from several locations within the
premises to check for consistent response.
5. Instruct the user to test the help button weekly.
Pin-Mount Adapter
Insert
Pin
Slip
Rope Necklace
Through
Snap-On
Posts