User's Manual
Table Of Contents
- Water Resistant Personal Help Button
- Product Summary
- Assembly Guidelines
- Assembly Options
- Wall Mount
- Belt Clip
- Wrist Bands
- 1. Lay the hook and latch wrist band across the back of the help button.
- 2. Compress the spring-loaded pins with a small screw driver
- 3. Slip the pins over the wrist band and into the pin slots located on the back of the help button.
- 1. Insert the spring-loaded pins through the ends of the plastic wrist band.
- 2. Compress the spring-loaded pins with a small screw driver.
- 3. Slip into the pin slots located on the back of the help button.
- Pendant
- 1. Make sure the necklace or chain fits through the larger hole in the pin-mounted necklace adapter.
- 2. Remove one of the spring-loaded pins from the plastic wrist band and insert it into the smaller hole on the necklace adapter.
- 3. Compress the spring-loaded pins with a small screw driver and slip them into the pin slots located on the back of the help button.
- 1. Slip the rope necklace into the top slot on the pendant adapter and hook the plastic ends together.
- 2. Snap the help button onto the four snap-on posts on the pendant adapter.
- Programming
- Testing the Help Button
- 1. Set the system to the Dealer Sensor Test mode.
- 2. Activate the help button by grasping the help button in your hand pressing it with your thumb or finger until the light blinks.
- 3. Listen for beeps sounded from system sirens. You should hear at least 7 beeps.
- 4. Test the help button from several locations within the premises to check for consistent response.
- 5. Instruct the user to test the help button weekly.
- Repair of the Help Button
- 1. Disassemble the help button by removing the four screws on the back of the help button and separate the cover and base.
- 2. Remove the old battery from its holder and install the new battery, observing polarity.
- 3. Reassemble the help button. Make sure to line up the LED indicator bump on the cover with the LED on the PCB.
- 4. Test the help button as described in “Testing the Help Button” section.
- 1. Disassemble the help button by removing the four screws on the back of the help button and separate the cover and base.
- 2. Reassemble the help button using the new cover. Make sure to line up the LED indicator bump on the cover with the LED on the PCB.
- Lithium Battery Disposal
- Specifications
- Notices
1
,QVWDOODWLRQ,QVWUXFWLRQV
*(6HFXULW\
'
ZZZ*(6HFXULW\FRP
Product Summary
The Water Resistant Personal Help Button is a wireless
device used for activating police, medical or auxiliary
alarms throughout the premises. When the help button is
pressed, the light mounted under the cover will blink and
an alarm signal is transmitted.
The status of the battery is sent in every transmission.
The battery is field replaceable.
The help button has four adapters that easily attach to the
back of the button. Using these adapters, the help button
can be mounted on the wall or worn as a belt clip, watch
or pendant.
Assembly Guidelines
Use the following guidelines when assembling the help
button.
• The help button should be learned into supervised
groups when used for life safety applications.
• The transmitter in the help button has an open-air
range of at least 375 feet, but the installation environ-
ment may influence this range.
• Have the customer press the help button with their
thumb or finger to ensure that they have no problems
activating the help button.
• When worn as a pendant, instruct your customer to
grasp the help button in their hand and press it using a
thumb or finger as opposed to pressing it against their
chest. This will give them the best transmitting range.
Assembly Options
Wall Mount
1. Place the wall mount adapter on the wall at the desired
location and mark through the mounting holes with a
pencil.
2. Secure the holder to the wall with #4 screws. Use
plasterboard anchors where studs are not present.
3. Snap the help button onto the four snap-on posts on
the wall mount adapter.
Belt Clip
The help button can be worn on the belt using the belt
clip adapter. Snap the help button onto the four snap-on
posts on the belt clip adapter.
Wrist Bands
The help button can be worn on the wrist with a hook and
latch or plastic wrist band.
To use the hook and latch wrist band:
1. Lay the hook and latch wrist band across the back of
the help button.
2. Compress the spring-loaded pins with a small screw-
driver
3. Slip the pins over the wrist band and into the pin slots
located on the back of the help button.
Note
Listen for a clicking sound as the pins slide into the slots.
Wall Mount Adapter
Belt Clip Adapter
Pendant Adapter
Pin-Mounted Necklace
Adapter
Snap-On
Posts
Mounting
Holes
Snap-On
Posts
Hook and Latch
Wrist Band
Insert Pin
Insert Pin
Document Number: 466-1815 Rev. E
May 2004 PRELIMINARY
:DWHU5HVLVWDQW
3HUVRQDO+HOS%XWWRQ