Install Manual
Table Of Contents
- Dialog Telephone Interface Module
- Product Summary
- Installation
- Installation Guidelines
- Programming-Adding the DTIM to Panel Memory
- 1. Remove the DTIM cover and install the antennas (see Figure 1).
- 2. With the system disarmed, enter program mode at the Allegro panel by pressing 8 + CODE.
- 3. Press twice and É twice. The Allegro display shows zone 01 - trip.
- 4. Locate the DTIM tamper switch and LED (see Figure 2 at left).
- 5. Press and release the DTIM tamper switch as follows:
- 6. Exit from program mode.
- Testing DTIM Transmitting Range
- 1. Place the DTIM in the desired location.
- 2. Put the Allegro panel into sensor test mode. The panel piezo should sound 7 - 8 beeps. This indicates good reception from the DTIM to the panel.
- 3. If you hear fewer than 7 beeps, test the DTIM in different locations. Mounting locations should be limited to areas where the panel responds with 7 - 8 beeps.
- 4. To retest transmitting range after relocating the DTIM, press Ç then É at the Allegro panel and listen for 7 - 8 beeps.
- 5. Exit from test mode after determining acceptable locations.
- Mounting
- Wiring a Phone Line to the Module
- 1. Run a 4-conductor cable from the TELCO block to the RJ-31X (A in Figure 4).
- 2. Connect the 4-conductor cable wires to the RJ-31X (B in Figure 4).
- 3. Disconnect the Green and Red premises phone jack wires from the TELCO block and splice them to the 4-conductor cable Black and White (or Yellow) wires (C in Figure 4). Use weath erproof wire connectors for these splices.
- 4. Connect the 4-conductor cable Green and Red wires to the TELCO block TIP (+) and Red to RING (-) posts (D in Figure 4).
- 5. Insert the 8-conductor phone cord plug into the RJ-31X jack (E in Figure 4).
- 6. Remove the right knockout on the DTIM plastic, feed the 4-conductor phone cord plug through it and connect the plug into the DTIM phone jack (Figure 5 at right).
- Phone Test
- 1. Call the central monitoring station to inform them you are testing the system.
- 2. Make sure the panel has the correct account number and central station receiver phone num ber programmed.
- 3. Enter the appropriate phone test command for the panel used in the system.
- 4. Contact the central monitoring station when you are finished testing.
- Installing the Battery Ty-wrap and Cover Screw (UL Listed Installations Only)
- Trouble- shooting
- Specifications
- Notices
2
Dialog Telephone Interface Module Installation Instructions
Preliminary 10/4/02
Programming—Adding the DTIM to Panel Memory
Note
We recommend learning the DTIM into Allegro panels as zone 1, since zone 1 is set up to learn
into Group 36 automatically and has pre-programmed sensor text for the DTIM (PHONE MOD-
ULE).
The DTIM uses a 3-2-1 tamper switch activation sequence for learning, which causes the
LED to blink in a corresponding 3-2-1 sequence. You must wait for the LED to turn off after
each flash sequence before releasing the tamper switch (see Figure 2).
To learn the DTIM into the panel:
1. Remove the DTIM cover and install the antennas (see Figure 1).
Figure 1. Antenna Installation
Note
Antennas must be installed for learning.
2. With the system disarmed, enter program mode at the Allegro panel by pressing
8 + CODE.
3. Press twice and
ƒ twice. The Allegro display shows ZONE 01 - TRIP.
4. Locate the DTIM tamper switch and LED (see Figure 2 at left).
Important !
Timing is the key to success with step 5. Read the complete step before you begin to help
ensure successful programming. Do not wait more than 1 second between tamper switch activa-
tions in step 5. If you wait too long, the LED will not flash and you must start over. Also, do not
release the tamper switch before the LED is done flashing or you must start over.
5. Press and release the DTIM tamper switch as follows:
Press 3 times, holding the tamper switch down on the third press until the LED flashes 3
times, then release after the third flash.
Immediately press 2 times, holding the tamper switch down on the second press until the
LED flashes 2 times, then release after the second flash.
Immediately press and hold until the LED flashes 1 time, then release the tamper switch.
6. Exit from program mode.
Testing DTIM Transmitting Range
The following describes the basic steps for testing transmitting range from the DTIM to the
panel. For complete testing instructions, see the panel installation instructions.
Note
Be sure to attach the cover onto the DTIM before testing wireless communications.
1. Place the DTIM in the desired location.
2. Put the Allegro panel into sensor test mode. The panel piezo should sound 7 - 8 beeps.
This indicates good reception from the DTIM to the panel.
3. If you hear fewer than 7 beeps, test the DTIM in different locations. Mounting locations
should be limited to areas where the panel responds with 7 - 8 beeps.
4. To retest transmitting range after relocating the DTIM, press
‚ then ƒ at the Allegro
panel and listen for 7 - 8 beeps.
5. Exit from test mode after determining acceptable locations.
Align antenna.. ...push down until bare metal is
not visible. Repeat for other
antenna.
LED
Tamper Switch
Figure 2. Tamper Switch and
LED Locations