Install Manual
Table Of Contents
- Appendix B: Reference Tables
- About This Manual
- Special Installation Requirements
- Planning the Installation
- Installing the System
- The panel must be mounted at least 10 feet from any DTIM or between any two DTIMs.
- Mounting the Panel
- 1. Remove the panel from the back mounting plate by lifting the tab located on the top and pullin...
- 2. Remove the wiring knockout.
- 3. Feed all device wires through the knockout and place the back mounting plate in position again...
- 4. Level the back mounting plate and mark the top and bottom mounting holes.
- 5. Install anchors where studs are not present.
- 6. Partially insert a screw into the top mounting hole location then hang the back mounting plate...
- 7. Recheck for level, insert the lower screw, and tighten both mounting screws.
- 8. Install the antenna. There are three antenna options to choose from:
- 9. Place panel cabinet into back mounting plate and snap into place.
- Connecting Detection Devices to Panel Zone Inputs
- Connecting the AC Power Transformer (22-117)
- Connecting the Backup Battery Pack
- Figure 7. Connecting the Battery Pack
- 1. Remove the panel housing from the back mounting plate by lifting the tab located on the top of...
- 2. Slide the battery pack into the space provided on the back of the panel (Figure 8).
- 3. Plug the battery pack lead into the slot provided next to the wire terminals (Figure 7).
- 4. Replace the panel housing into back mounting plate and snap into place.
- Powering Up the Panel
- Programming the Panel
- Mounting the Panel
- Do not wait more than 1-2 seconds between steps 5 and 6 or steps 6 and 7 after releasing the tamp...
- Figure 10. DTIM Tamper Switch and LED Locations
- 1. Remove the DTIM cover.
- 2. Press twice and # once. The display shows phones; devices; add.
- 3. Press #. The display shows zone 01 - trip.
- 4. Press the DTIM’s tamper switch three times, holding the tamper switch down on the third press ...
- 5. Press the DTIM tamper switch twice, holding the tamper switch down on the second press and wai...
- 6. Press and hold the tamper switch down until the LED flashes once. The panel beeps once indicat...
- Account Menu (1st Tier)
- Phones Menu (1st Tier)
- Number 1 and 2 (Phones—Phone 1 and Phone 2)
- 3rd Tier
- FMT - CID (Phones—Phone 1 and Phone 2)
- 3rd Tier
- High Lvl (Phones—Phone 1 and Phone 2)
- 3rd Tier
- Low Lvl (Phones—Phone 1 and Phone 2)
- 3rd Tier
- Openings (Phones—Phone 1 and Phone 2)
- 3rd Tier
- Closings (Phones—Phone 1 and Phone 2)
- 3rd Tier
- Backup (Phones—Phone 2)
- 3rd Tier
- Dial Dly (Phones)
- 2nd Tier
- Pre-Dial String (Phones)
- 2nd Tier
- DTMF Dial (Phones)
- 2nd Tier
- Devices (1st Tier)
- Table 2: Sensor Group Assigned to Device
- Table 3: Device Programming
- Add (Devices)
- 2nd Tier
- Delete (Devices)
- 2nd Tier
- Review (Devices)
- 2nd Tier
- Text (Devices)
- 2nd Tier
- 1. To select the zone you want to add text to press , till you get to the correct zone then press...
- 2. Press # then to scroll thru the base words, press # to select the word you want.
- 3. Press to change to the prefix words. Press # then to scroll thru the prefix words. Press # to ...
- 4. Press to change to the suffix words. Press # then to scroll thru the suffix words. Press # to ...
- 5. Press * to review what has been selected, then press to go to the next zone to change.
- 6. Repeat steps 2 thru 4 to change all zones.
- Table 4: Sensor Text
- Downloader (1st Tier)
- Codes (1st Tier)
- Timers (1st Tier)
- Fire related trouble beeps are not affected by Sleepy Time.
- Sleep Hour (Timers)
- 2nd Tier
- Options (1st Tier)
- KTP Arm (Options)
- 2nd Tier
- Police Panic (Options)
- 2nd Tier
- Emergency Panic (Options)
- 2nd Tier
- Fire Panic (Options)
- 2nd Tier
- Rcvr Trouble (Options)
- 2nd Tier
- Panel Tamper (Options)
- 2nd Tier
- Exit Ext (Options)
- 2nd Tier
- Swinger Shutdown (Options)
- 2nd Tier
- Quick Arm (Options)
- 2nd Tier
- Quick Exit (Options)
- 2nd Tier
- Auto Stay Arm (Options)
- 2nd Tier
- Supv Time (Options)
- 2nd Tier
- Alarm Verify (Options)
- 2nd Tier
- Demo Kit (Options)
- 2nd Tier
- Reports (1st Tier)
- Siren (1st Tier)
- Exit - DL (1st Tier)
- User Programing Menu Items
- Downloader Programming
- ToolBox Downloader Programming
- 1. Contact your downloader station and ask the operator to prepare to download to the panel.
- 2. Make sure the system is disarmed.
- 3. Go into installer program mode.
- 4. Press * to go to the exit - dl display.
- 5. Enter the installer or dealer code.
- 6. When the downloader session completes, a panel programmed status message will be displayed.
- 1. Call the panel location.
- 2. Let the phone ring once, then hang up.
- 3. Wait at least 10 seconds but not more than 40, then call the panel location again. The panel s...
- ToolBox Downloader Programming
- Testing the System
- Allegro
- Appendix A: Troubleshooting
- 1. Check that panel transformer is plugged into an unswitched outlet.
- 2. Check the AC circuit breaker to be sure the circuit is live.
- 3. Check that the backup battery is installed correctly and the AC power transformer is plugged in.
- 4. Check for proper panel and transformer wiring.
- 5. Measure the incoming AC voltage at panel terminals 1 and 2. It should read about 8 VAC.
- 1. Unplug the AC power transformer and disconnect the wires from the transformer and the panel.
- 2. Check transformer to panel wire for short or open circuits.
- 3. Plug in the transformer and check for 8.0 VAC at the transformer unconnected terminals. If zer...
- 1. Perform a battery test by entering and exiting sensor test.
- 2. Check that the backup battery is installed correctly and the AC power transformer is plugged in.
- 3. Measure the incoming AC voltage at the panel terminals 1 and 2. It should read about 8 VAC.
- 4. Remove the backup battery power by disconnecting the battery and replace the battery.
- 1. Check the AC circuit breaker to be sure the circuit is live.
- 2. Check for proper panel and transformer wiring.
- 3. Check that the transformer is supplying AC to the panel.
- 4. Check that the transformer is plugged into a nonswitched outlet and secured with the provided ...
- 1. Check your records to see if you have the customer’s access code(s) on file.
- 2. Verify the access code(s) using the Downloader.
- 3. Clear memory and reprogram the panel locally.
- 4. Use Apartment Manager code to enter program mode and view the primary and user codes.
- 1. Check your records to see if you have the install code on file.
- 2. Verify the install code using the Downloader.
- 3. Use the Dealer Code to enter program mode and view the installer code.
- 4. Call Technical Support for assistance.
- 1. Press STATUS for an indication of the problem.
- 2. Make sure all monitored perimeter doors and windows are closed.
- 3. Make sure all perimeter and interior sensors are closed.
- 1. Attempting to bypass a 24-hour sensor (a sensor that is active in all levels) that cannot be b...
- 2. Sensor is not active in the current arming level.
- 3. Sensor is not learned in.
- 1. Check that the premises phone line is working.
- 2. Perform a phone test.
- 3. Check for correct phone line wiring between the DTIM and RJ-31X Jack (see DTIM Installation In...
- 4. Verify that central station phone number is programmed into the panel. If necessary, reprogram...
- 5. Verify that the correct phone format (SIA or CID) is being used.
- 1. Sensor is not active in current arming level. Verify sensor group and retest.
- 2. Zone is not learned into panel memory. Enter installer program mode. Go to Devices, then Add a...
- 3. Verify wiring.
- 1. Check that the wireless sensor battery is installed.
- 2. Check the sensor battery for low voltage. Replace batteries, if necessary.
- 3. Use an RF Sniffer (60-401) to verify that sensor is transmitting.
- 4. Constant beeps from the RF Sniffer indicate a runaway (faulty) sensor. Remove the sensor’s bat...
- 5. Sensor is not learned into panel memory. Enter installer program mode—Devices, Add, and learn ...
- 6. Sensor may be out of range. Move sensor to another location.
- 1. Sensor tamper switch is tripped—sensor cover is off, not latched securely, or sensor is not mo...
- 2. Check the sensor battery for low voltage. Replace batteries, if necessary.
- 1. Use an RF Sniffer (60-401) to verify that sensor is transmitting. If sensor is not transmittin...
- 2. Change mounting position of sensor (from horizontal to vertical or vice versa) and test sensor...
- 3. Sensor signal is not reaching panel/receiver because sensor is too far away or there is too mu...
- 1. Perform a sensor test.
- 2. Call technical support for assistance.
- 1. Replace the battery and perform a sensor test.
- 2. Call technical support.
- 1. Perform a phone test.
- 2. Check to make sure manual phone test option is on.
- 3. Verify that high and/or low level reporting option is on.
- 4. Perform a sensor test to verify communication between the DTIM and panel. See Phone Test (Repo...
- 5. Check DTIM wiring (see DTIM installation instructions).
- 1. Verify Downloader Phone Number matches ToolBox setting.
- 2. Verify Downloader CODE matches ToolBox setting.
- 3. Verify Dealer CODE matches ToolBox setting.
- 4. Verify panel Account Number matches ToolBox setting.
- 1. Verify Downloader Phone Number matches ToolBox setting.
- 2. Verify Downloader CODE matches ToolBox setting.
- 3. Verify Dealer CODE matches ToolBox setting.
- FCC Notices
- Specifications
- Appendix A: Troubleshooting
5
Allegro
Preliminary 2/5/02
To connect the backup battery pack:
Figure 7. Connecting the Battery Pack
1. Remove the panel hous-
ing from the back
mounting plate by lift-
ing the tab located on
the top of the panel and
pulling back.
2. Slide the battery pack
into the space provided
on the back of the panel
(Figure 8).
Figure 8.Placement of Battery
3. Plug the battery pack lead into the slot provided next to
the wire terminals (Figure 7).
Note
Be sure to run the battery pack wires below the battery and
thru the wire channel.
4. Replace the panel housing into back mounting plate
and snap into place.
Note
See Appendix A: Troubleshooting on page 19 if the panel
displays
LOW BATTERY.
Powering Up the Panel
After connecting and wiring all devices to the panel, you are
ready to apply AC power to the panel.
To power up the panel:
Plug the transformer into an outlet that is not controlled
by a switch or ground fault circuit interrupt (GFCI). Be
sure to screw the top of the transformer onto the outlet
so that doesn’t fall out of the outlet.
The message,
PANEL POWERED UP, will be displayed
WARNING
!
Be careful when securing the transformer to an outlet with
a metal cover. Hold the cover tightly in place. You could
receive a serious shock if the metal outlet cover drops
down onto the prongs of the plug while you are securing
the transformer and cover to the outlet box.
Note
If the panel does not display anything, immediately unplug
the transformer and disconnect the backup battery. Refer
to the “Troubleshooting” (on page 19) section.
Programming the Panel
This section describes how to program all settings found in
programming mode. You can program the panel manually
using the panel keypad to program on site. Or, using the
ToolBox software, you can automatically program remotely
via a modem and phone line.
Panel Keypad Button Programming
Functions
In program mode, panel keypad buttons let you navigate to
all installer programming menus for configuring the system.
Table 1 describes the panel keypad button functions in pro-
gram mode.
Moving Through Program Mode Tiers
and Menus
There are three tiers of programming menus. Tier 1 menus
are accessible immediately after entering program mode.
In Figure 9 arrows pointing right represent pressing
to
advance forward through the menus. Arrows pointing left
represent pressing
to move through the menus in reverse.
The arrows below the tier 1 menu represents pressing
ƒ
and ‚ buttons.
Figure 9. Tier 1 Programming Menus
To advance to tier 2 program menus press the up or down
arrow keys to scroll thru the tier 1 menus. When you find
the menu you want to make changes to press
ƒ once. This
will take you to tier 2 program menus.
Installer Programing Menu Items
This section guides you through the installer programing
menu items as they appear in sequence with the exception
of clearing memory.
Entering Installer Programming Mode
Entering programming mode on site is done from the panel,
using an installer code. The default installer code is
8 6 6 0
g
4 6 a . d s f
Battery Pack
Battery Pack
Battery Pack
Location
Battery Slot
Wire Terminals
Lead
Wire Channel
Table 1: Button Functions
Button Programming Function
Selects menu item or data entry. Toggles between
on and off whenever needed.
Deselects menu item or data entry (if pressed
before #).
Scroll through available options at the current
menu tier.
0 thru 9 Enter numeric values wherever needed.
#
B y p a s s
S e l e c t
B a c k
*
S t a t u s
T i m e r sP h o n e s
D e v i c e s D o w n l o a d e r
C o d e s
A c c o u n t
#
*
#
*
#
*
#
*
#
*
#
*
C l e a r
M e m o r y
E x i t - D L
R e p o r t s
S i r e nO p t i o n s
#
*
#
*
#
*
#
*
#
*
T i e r 1 M e n u