Install Manual
Table Of Contents
- Appendix B: Reference Tables
- About This Manual
- Special Installation Requirements
- Planning the Installation
- Installing the System
- The panel must be mounted at least 10 feet from any DTIM or between any two DTIMs.
- Mounting the Panel
- 1. Remove the panel from the back mounting plate by lifting the tab located on the top and pullin...
- 2. Remove the wiring knockout.
- 3. Feed all device wires through the knockout and place the back mounting plate in position again...
- 4. Level the back mounting plate and mark the top and bottom mounting holes.
- 5. Install anchors where studs are not present.
- 6. Partially insert a screw into the top mounting hole location then hang the back mounting plate...
- 7. Recheck for level, insert the lower screw, and tighten both mounting screws.
- 8. Install the antenna. There are three antenna options to choose from:
- 9. Place panel cabinet into back mounting plate and snap into place.
- Connecting Detection Devices to Panel Zone Inputs
- Connecting the AC Power Transformer (22-117)
- Connecting the Backup Battery Pack
- Figure 7. Connecting the Battery Pack
- 1. Remove the panel housing from the back mounting plate by lifting the tab located on the top of...
- 2. Slide the battery pack into the space provided on the back of the panel (Figure 8).
- 3. Plug the battery pack lead into the slot provided next to the wire terminals (Figure 7).
- 4. Replace the panel housing into back mounting plate and snap into place.
- Powering Up the Panel
- Programming the Panel
- Mounting the Panel
- Do not wait more than 1-2 seconds between steps 5 and 6 or steps 6 and 7 after releasing the tamp...
- Figure 10. DTIM Tamper Switch and LED Locations
- 1. Remove the DTIM cover.
- 2. Press twice and # once. The display shows phones; devices; add.
- 3. Press #. The display shows zone 01 - trip.
- 4. Press the DTIM’s tamper switch three times, holding the tamper switch down on the third press ...
- 5. Press the DTIM tamper switch twice, holding the tamper switch down on the second press and wai...
- 6. Press and hold the tamper switch down until the LED flashes once. The panel beeps once indicat...
- Account Menu (1st Tier)
- Phones Menu (1st Tier)
- Number 1 and 2 (Phones—Phone 1 and Phone 2)
- 3rd Tier
- FMT - CID (Phones—Phone 1 and Phone 2)
- 3rd Tier
- High Lvl (Phones—Phone 1 and Phone 2)
- 3rd Tier
- Low Lvl (Phones—Phone 1 and Phone 2)
- 3rd Tier
- Openings (Phones—Phone 1 and Phone 2)
- 3rd Tier
- Closings (Phones—Phone 1 and Phone 2)
- 3rd Tier
- Backup (Phones—Phone 2)
- 3rd Tier
- Dial Dly (Phones)
- 2nd Tier
- Pre-Dial String (Phones)
- 2nd Tier
- DTMF Dial (Phones)
- 2nd Tier
- Devices (1st Tier)
- Table 2: Sensor Group Assigned to Device
- Table 3: Device Programming
- Add (Devices)
- 2nd Tier
- Delete (Devices)
- 2nd Tier
- Review (Devices)
- 2nd Tier
- Text (Devices)
- 2nd Tier
- 1. To select the zone you want to add text to press , till you get to the correct zone then press...
- 2. Press # then to scroll thru the base words, press # to select the word you want.
- 3. Press to change to the prefix words. Press # then to scroll thru the prefix words. Press # to ...
- 4. Press to change to the suffix words. Press # then to scroll thru the suffix words. Press # to ...
- 5. Press * to review what has been selected, then press to go to the next zone to change.
- 6. Repeat steps 2 thru 4 to change all zones.
- Table 4: Sensor Text
- Downloader (1st Tier)
- Codes (1st Tier)
- Timers (1st Tier)
- Fire related trouble beeps are not affected by Sleepy Time.
- Sleep Hour (Timers)
- 2nd Tier
- Options (1st Tier)
- KTP Arm (Options)
- 2nd Tier
- Police Panic (Options)
- 2nd Tier
- Emergency Panic (Options)
- 2nd Tier
- Fire Panic (Options)
- 2nd Tier
- Rcvr Trouble (Options)
- 2nd Tier
- Panel Tamper (Options)
- 2nd Tier
- Exit Ext (Options)
- 2nd Tier
- Swinger Shutdown (Options)
- 2nd Tier
- Quick Arm (Options)
- 2nd Tier
- Quick Exit (Options)
- 2nd Tier
- Auto Stay Arm (Options)
- 2nd Tier
- Supv Time (Options)
- 2nd Tier
- Alarm Verify (Options)
- 2nd Tier
- Demo Kit (Options)
- 2nd Tier
- Reports (1st Tier)
- Siren (1st Tier)
- Exit - DL (1st Tier)
- User Programing Menu Items
- Downloader Programming
- ToolBox Downloader Programming
- 1. Contact your downloader station and ask the operator to prepare to download to the panel.
- 2. Make sure the system is disarmed.
- 3. Go into installer program mode.
- 4. Press * to go to the exit - dl display.
- 5. Enter the installer or dealer code.
- 6. When the downloader session completes, a panel programmed status message will be displayed.
- 1. Call the panel location.
- 2. Let the phone ring once, then hang up.
- 3. Wait at least 10 seconds but not more than 40, then call the panel location again. The panel s...
- ToolBox Downloader Programming
- Testing the System
- Allegro
- Appendix A: Troubleshooting
- 1. Check that panel transformer is plugged into an unswitched outlet.
- 2. Check the AC circuit breaker to be sure the circuit is live.
- 3. Check that the backup battery is installed correctly and the AC power transformer is plugged in.
- 4. Check for proper panel and transformer wiring.
- 5. Measure the incoming AC voltage at panel terminals 1 and 2. It should read about 8 VAC.
- 1. Unplug the AC power transformer and disconnect the wires from the transformer and the panel.
- 2. Check transformer to panel wire for short or open circuits.
- 3. Plug in the transformer and check for 8.0 VAC at the transformer unconnected terminals. If zer...
- 1. Perform a battery test by entering and exiting sensor test.
- 2. Check that the backup battery is installed correctly and the AC power transformer is plugged in.
- 3. Measure the incoming AC voltage at the panel terminals 1 and 2. It should read about 8 VAC.
- 4. Remove the backup battery power by disconnecting the battery and replace the battery.
- 1. Check the AC circuit breaker to be sure the circuit is live.
- 2. Check for proper panel and transformer wiring.
- 3. Check that the transformer is supplying AC to the panel.
- 4. Check that the transformer is plugged into a nonswitched outlet and secured with the provided ...
- 1. Check your records to see if you have the customer’s access code(s) on file.
- 2. Verify the access code(s) using the Downloader.
- 3. Clear memory and reprogram the panel locally.
- 4. Use Apartment Manager code to enter program mode and view the primary and user codes.
- 1. Check your records to see if you have the install code on file.
- 2. Verify the install code using the Downloader.
- 3. Use the Dealer Code to enter program mode and view the installer code.
- 4. Call Technical Support for assistance.
- 1. Press STATUS for an indication of the problem.
- 2. Make sure all monitored perimeter doors and windows are closed.
- 3. Make sure all perimeter and interior sensors are closed.
- 1. Attempting to bypass a 24-hour sensor (a sensor that is active in all levels) that cannot be b...
- 2. Sensor is not active in the current arming level.
- 3. Sensor is not learned in.
- 1. Check that the premises phone line is working.
- 2. Perform a phone test.
- 3. Check for correct phone line wiring between the DTIM and RJ-31X Jack (see DTIM Installation In...
- 4. Verify that central station phone number is programmed into the panel. If necessary, reprogram...
- 5. Verify that the correct phone format (SIA or CID) is being used.
- 1. Sensor is not active in current arming level. Verify sensor group and retest.
- 2. Zone is not learned into panel memory. Enter installer program mode. Go to Devices, then Add a...
- 3. Verify wiring.
- 1. Check that the wireless sensor battery is installed.
- 2. Check the sensor battery for low voltage. Replace batteries, if necessary.
- 3. Use an RF Sniffer (60-401) to verify that sensor is transmitting.
- 4. Constant beeps from the RF Sniffer indicate a runaway (faulty) sensor. Remove the sensor’s bat...
- 5. Sensor is not learned into panel memory. Enter installer program mode—Devices, Add, and learn ...
- 6. Sensor may be out of range. Move sensor to another location.
- 1. Sensor tamper switch is tripped—sensor cover is off, not latched securely, or sensor is not mo...
- 2. Check the sensor battery for low voltage. Replace batteries, if necessary.
- 1. Use an RF Sniffer (60-401) to verify that sensor is transmitting. If sensor is not transmittin...
- 2. Change mounting position of sensor (from horizontal to vertical or vice versa) and test sensor...
- 3. Sensor signal is not reaching panel/receiver because sensor is too far away or there is too mu...
- 1. Perform a sensor test.
- 2. Call technical support for assistance.
- 1. Replace the battery and perform a sensor test.
- 2. Call technical support.
- 1. Perform a phone test.
- 2. Check to make sure manual phone test option is on.
- 3. Verify that high and/or low level reporting option is on.
- 4. Perform a sensor test to verify communication between the DTIM and panel. See Phone Test (Repo...
- 5. Check DTIM wiring (see DTIM installation instructions).
- 1. Verify Downloader Phone Number matches ToolBox setting.
- 2. Verify Downloader CODE matches ToolBox setting.
- 3. Verify Dealer CODE matches ToolBox setting.
- 4. Verify panel Account Number matches ToolBox setting.
- 1. Verify Downloader Phone Number matches ToolBox setting.
- 2. Verify Downloader CODE matches ToolBox setting.
- 3. Verify Dealer CODE matches ToolBox setting.
- FCC Notices
- Specifications
- Appendix A: Troubleshooting
Preliminary 2/5/02
FCC Notices
FCC Part 15 Information to the User
Changes or modifications not expressly approved by Interlogix Inc. can void the user’s authority to operate the equipment.
FCC Part 15 Class B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
❑ Reorient or relocate the receiving antenna.
❑ Increase the separation between the equipment and receiver.
❑ Connect the affected equipment and the panel receiver to separate outlets, on different branch circuits.
❑ Consult the dealer or an experienced radio/TV technician for help.
FCC ID: B42-785B-ALGRO
2266 Second Street North | North Saint Paul Mn | 55109 | 800-777-2624 | www.interlogixinc.com
©2001 Interlogix,™ Inc. Interlogix is a trademark of Interlogix, Inc. ITI is a registered trademark of Interlogix, Inc.