Install Manual

ManualsBrandsUTC Fire & Security Americas ManualsElectronicsSecurity Panel

Table Of Contents

8 6 6 0 g 1 0 a . d s f

Contents

,QVWDOODWLRQ,QVWUXFWLRQV

Preliminary 2/5/02

About This Manual ............................................................1

Special Installation Requirements .....................................1

UL Listed Systems .....................................................1

Basic System .........................................................1

Household Burglary Alarm System

Unit (UL 1023) ......................................................1

Household Fire Warning System (UL 985) ...........1

Digital Alarm Communicator System (UL 1635) .1

Central Station Reporting ......................................1

UL-Canada Listed Systems ........................................1

California State Fire Marshall Listed Systems ...........1

Planning the Installation ....................................................1

Standard System .........................................................1

Panel ......................................................................1

DTIM .....................................................................1

Additional System Components ............................2

Installing the System .........................................................2

Determine the Panel Location ....................................2

Mounting the Panel ....................................................2

Connecting Detection Devices to Panel Zone Inputs .3

Connecting Intrusion Detection Devices ...............3

Connecting the AC Power Transformer .....................3

Connecting the Backup Battery Pack .........................3

Powering Up the Panel ...............................................4

Programming the Panel .....................................................4

Panel Keypad Button Programming Functions ..........4

Moving Through Program Mode Tiers

and Menus ..................................................................4

Installer Programing Menu Items ...............................4

Entering Installer Programming Mode ..................4

Clearing Memory .................................................. 5

Learning the DTIM into the Panel ........................5

Account Menu .......................................................5

Account ............................................................5

Phones Menu .........................................................5

Number 1 and 2................................................ 5

FMT - CID ....................................................... 6

High Lvl ........................................................... 6

Low Lvl............................................................ 6

Openings .......................................................... 6

Closings ............................................................6

Backup ..............................................................6

Dial Dly ............................................................6

Pre-Dial String.................................................. 7

DTMF Dial ...................................................... 7

Devices ..................................................................7

Add .................................................................. 7

Delete ............................................................... 7

Review ............................................................. 8

Text .................................................................. 8

Downloader ...........................................................9

Number............................................................. 9

DL Code ........................................................... 9

Codes .................................................................... 9

Install Code....................................................... 9

Dealer Code...................................................... 9

Duress Code ..................................................... 9

Apartment Manager ......................................... 9

Timers ..................................................................10

Entry Dly ........................................................ 10

Exit Dly .......................................................... 10

Phone Test Frequency..................................... 10

Next Phone Test ............................................. 10

Sleepy Time.................................................... 10

Sleep Hour...................................................... 10

Options ................................................................10

KTP Arm ........................................................ 10

Police Panic ................................................... 10

Emergency Panic ........................................... 11

Fire Panic ....................................................... 11

Rcvr Trouble................................................... 11

Panel Tamper ..................................................11

Exit Ext........................................................... 11

Swinger Shutdown ......................................... 11

Quick Arm...................................................... 11

Quick Exit....................................................... 12

Auto Stay Arm................................................ 12

Supv Time....................................................... 12

Alarm Verify................................................... 12

Demo Kit ........................................................ 13

Zones ..............................................................13

Reports .................................................................13

AC Fail ........................................................... 13

Low CPU Battery........................................... 13

Phone Test ...................................................... 13

Auto Phone Test ............................................. 14

Siren .....................................................................14

Siren Time Out ...............................................14

Trouble Beeps................................................. 14

Alarm Volume ................................................14

Exit - DL ..............................................................14

User Programing Menu Items ...................................14

Entering User Programming Mode .....................14

Document Number: 466-1821 Rev. A PRELIMINARY

February 2002

$OOHJUR

ITI Part No. 60-874-95

Summary of content (31 pages)

PAGE 1
Preliminary 2/5/02 ITI Part No. 60-874-95 $OOHJUR Document Number: 466-1821 Rev. A PRELIMINARY February 2002 Contents About This Manual ............................................................ 1 Special Installation Requirements ..................................... 1 UL Listed Systems ..................................................... 1 Basic System ......................................................... 1 Household Burglary Alarm System Unit (UL 1023) ..........................................
PAGE 2
Preliminary 2/5/02 Codes ................................................................... 14 Apartment Manager ....................................... 14 Primary .......................................................... 15 User 2, 3, 4 ..................................................... 15 Time .................................................................... 15 Phone Test ........................................................... 15 Sensor Test ....................................................
PAGE 3
Preliminary 2/5/02 FCC Notices FCC Part 15 Information to the User Changes or modifications not expressly approved by Interlogix Inc. can void the user’s authority to operate the equipment. FCC Part 15 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference in a residential installation.
PAGE 4
Preliminary 2/5/02 About This Manual Digital Alarm Communicator System (UL 1635) This manual provides information for planning, installing, programming, and testing this security system. When necessary, this manual refers you to other documentation included with compatible devices. Basic system, plus: Planning sheets are included for you to record hardware layout and software programming settings.
PAGE 5
Preliminary 2/5/02 wired detectors. Built-In Radio Receiver: Allows use of up to 20 ITI 319.5 MHz. crystal and/or SAW Learn Mode wireless sensors and touchpads. Built-In Siren: Capable of 85 dBa @ 3m. Built-In Panel Keypad. Liquid Crystal Display (LCD). Additional System Components The system can monitor up to 20 sensors using any combination of the following sensors: Door/Window Sensor (60-670-95R). 2-Button Keychain Touchpad (60-607-319.5).
PAGE 6
Preliminary 2/5/02 Panel Terminals 3 Antenna Loop 4 3 Or 4 Clips Normally Closed (N/C) Contacts In Series Normally Open (N/O) Contacts In Parallel 2k Ohm EOL Resistor 49-454 Figure 3. Antenna wiring as shipped Option 2: Hang antenna in wall (longest range). ➢ When you mark the back mounting plate’s two mounting holes, also mark where the antenna hole is (see Figure 2 for antenna wire hole location). ➢ Where the antenna hole was marked, drill a hole into the wall.
PAGE 7
Preliminary 2/5/02 To connect the backup battery pack: Battery Pack Battery Pack Location Wire Channel Battery Pack Lead Battery Slot using the panel keypad to program on site. Or, using the ToolBox software, you can automatically program remotely via a modem and phone line. Panel Keypad Button Programming Functions In program mode, panel keypad buttons let you navigate to all installer programming menus for configuring the system. Table 1 describes the panel keypad button functions in program mode.
PAGE 8
Preliminary 2/5/02 4321. The system can be put into program mode only when the system is disarmed. To learn the DTIM into the panel: 1. Remove the DTIM cover. To enter programming mode: 2. Press With the system disarmed, press 8 + CODE. To clear memory: 3. It is strongly recommended that you clear memory on all newly installed panels before programming.
PAGE 9
Preliminary 2/5/02 Phones Menu (1st Tier) The phone menu lets you set up central station reporting for the system.
PAGE 10
Preliminary 2/5/02 Dial Dly 2nd Tier (Phones) Table 2: Sensor Group Assigned to Device Device Sensor Group (Default = 30 seconds, Parameters = 15-120 seconds) Dial Delay determines how much time the user has to stop a panel before it sends a false alarm to the central station. Keyfob or RF Touchpad 1 Portable Panic 1 Alarm reports from sensors in groups 00–03, 10, and 13-20 can be aborted. To abort the dialing attempt, the user must disarm the system within the Dial Dly time setting.
PAGE 11
Preliminary 2/5/02 Delete 2nd Tier Prefix Field (Default = none) The following procedure describes how to remove hardwire and wireless sensors from panel memory. Note Deleting zones/sensors does not delete text associated with the deleted zone/sensor number. To delete a device: 1. To select a different zone press to scroll thru the learned zones. Press # to delete the displayed zone. The display shows the next sensor. 2. Repeat step 1 until all desired zones are deleted.
PAGE 12
Preliminary 2/5/02 Downloader (1st Tier) Number 2nd Tier (Downloader) (Default = none, Parameters = 24 digits; 0-9, *, #, pause) Use this setting to enter the phone number of an off-site computer that can be used to program the panel through the phone line. Phone numbers can be 1 to 24 digits long, including pauses or * and # characters (see Number 1 and 2 (Phones—Phone 1 and Phone 2) on page 7).
PAGE 13
Preliminary 2/5/02 Timers (1st Tier) Entry Dly 2nd Tier (Timers) (Default = 30 seconds, Parameters = 30-240 seconds) Entry Delay determines how much time the user has to disarm the system after entering the armed premises through a “designated delay door,” (grp 10) without causing an alarm. Note For UL Listed installations, the Entry Delay must be set to 45 seconds or less. To set the entry delay: Press #, enter desired time and then press #.
PAGE 14
Preliminary 2/5/02 Emergency Panic 2nd Tier (Options) (Default = off) This setting determines whether panel keypad emergency panic buttons are enabled (on) or disabled (off). If enabled, an immediate alarm will occur after the emergency panic buttons are pressed for two seconds and the panel displays the alarm as an emergency panic. If the DTIM is installed with the system; ❑ An alarm report will be issued. ❑ If the dialer delay option is on, the report will be delayed or can be aborted.
PAGE 15
Preliminary 2/5/02 Quick Exit 2nd Tier (Options) (Default = on) This setting determines whether or not users can open and close a standard entry/exit door without causing an alarm (while the system is armed). When Quick Exit is on, (while the system is armed) pressing the Quick Exit button starts a 2-minute timer that allows exit/ entry thru one standard entry/exit door (sensor group 10) to be activated (opened, then closed) for 2 minutes.
PAGE 16
Preliminary 2/5/02 Reports (1st Tier) Demo Kit 2nd Tier (Options) (Default = off) This setting determines whether the panel is used for a standard installation (off) or as a demo kit (on). The demo kit will include: ❑ Allegro panel ❑ SAW D/W ❑ 2 button key fob ❑ PIR plastic (motion sensor) ❑ DTIM plastic ❑ 9V alkaline battery with battery strap ❑ Soft-sided case ❑ Demo kit Instructions The following contains the modifications to Allegro Software that embody the Demo Kit Software.
PAGE 17
Preliminary 2/5/02 Auto Phone Test 2nd Tier (Reports) (Default = off) This setting determines if the panel sends a phone test automatically to the central station at Supervisory Time. Refer to the “Phone Test Frequency” and “Next Phone Test” on page 11. Note For UL Listed installations, the Auto Phone Test feature must be set to on. (Siren) (Default = 4 minutes, Parameters = 1-30) Siren Time-out determines how long sirens sound if no one is present to disarm the system.
PAGE 18
Preliminary 2/5/02 User 2, 3, 4 2nd Tier (Codes) (Default = none, Parameters = 4 digits, 0 to 9) User Codes performs arming and disarming functions. The user codes cannot directly bypass sensors or program the primary code. The system allows up to 3 user codes (user 2 - 4). To program/change user 2, 3, 4 code: 1. Press # to display the current user code (if any). 2. Press #, enter the desired user code and then press #.
PAGE 19
Preliminary 2/5/02 3. Volume 1st Tier (Volume) (Default = 0, Parameters = 0-5) This setting allows the user to adjust the panel’s status and arming level beep volume. The volume can be set from 0 to 5, with 0 being the lowest volume. To set the volume: 1. Press # to display the current volume. 2. Press #, enter the desired volume level and then press #. Wait at least 10 seconds but not more than 40, then call the panel location again. The panel should answer on the first ring.
PAGE 20
Preliminary 2/5/02 Table 6: Basic Operating Commands (Continued) How to... Command Press and hold both buttons until panel indicates alarm. A rm 1 Police Panic D is a r m N o D e la y 4 Emergency Panic Press and hold both buttons until panel indicates alarm. S ile n t C h im e 7 Fire Panic Press and hold both buttons until panel indicates alarm. Testing Sensors/Zones We recommend that you test sensors/zones after all programming is completed and whenever a sensor/zone-related problem occurs.
PAGE 21
Preliminary 2/5/02 Appendix A: Troubleshooting Feature Problem Action/Solution Panel Power Panel does not power up and does not display or respond. 1. 2. 3. 4. 5. Check that panel transformer is plugged into an unswitched outlet. Check the AC circuit breaker to be sure the circuit is live. Check that the backup battery is installed correctly and the AC power transformer is plugged in. Check for proper panel and transformer wiring. Measure the incoming AC voltage at panel terminals 1 and 2.
PAGE 22
Preliminary 2/5/02 Feature Problem Action/Solution System protests and will not arm immediately. 1. Press STATUS for an indication of the problem. 2. Make sure all monitored perimeter doors and windows are closed. 3. Make sure all perimeter and interior sensors are closed. Bypassing Sensor to bypass is not listed. 1. Attempting to bypass a 24-hour sensor (a sensor that is active in all levels) that cannot be bypassed. 2. Sensor is not active in the current arming level. 3. Sensor is not learned in.
PAGE 23
Preliminary 2/5/02 Feature Problem Action/Solution Wireless Sensor Zone (Continued) Panel indicates [sensor #] supervisory. 1. Use an RF Sniffer (60-401) to verify that sensor is transmitting. If sensor is not transmitting, check battery for low or no voltage and replace. 2. Change mounting position of sensor (from horizontal to vertical or vice versa) and test sensor several times for consistency. 3.
PAGE 24
Preliminary 2/5/02 Feature Problem Action/Solution Download/upload session fails on an unprogrammed panel. 1. Verify Downloader Phone Number matches ToolBox setting. 2. Verify Downloader CODE matches ToolBox setting. 3. Verify Dealer CODE matches ToolBox setting.
PAGE 25
Preliminary 2/5/02 Appendix B: Reference Tables Alarm Delay 1, 2, 3 Instant Emergency Instant √ √ 1, 2, 3 Emergency Instant √ 1, 2, 3 24-hour audible fixed emergency buttons. Police Instant 01 Portable Panic 24-hour audible portable emergency buttons. Police Instant 02 Fixed Panic 24-hour silent fixed emergency buttons. Silent Instant 03 Portable Panic 24-hour silent portable emergency buttons.
PAGE 26
Preliminary 2/5/02 Alarm Delay Chime Application CS Report Name Supervisory No. Restoral Table B1: Sensor Group Characteristics (Continued) Active Levels Note Check marks (√) represent characteristics present in a group. * This group is not certified as a primary protection circuit for UL-listed systems and is for supplementary use only. † Sounds instant police siren if two or more sensors are tripped within 4 minutes. Otherwise sensors are followers to delayed sensors.
PAGE 27
Preliminary 2/5/02 Table B2: System Settings (Continued) Menu Name & Default Parameters DL Code (12345) 5 digit code, 0-9 Install Code, 4321 4 digit code, 0-9 Dealer Code, none 4 digit code, 0-9 Duress Code, none 4 digit code, 0-9 Apartment Manager Code, none 4 digit code, 0-9 Entry DLY, 30 30-240 Exit DLY, 60 (60 for UL1023) 45-254 PH TST Freq, 7 1-255 NXT PH Test, 7 1-255 Sleepy Time, on (off for UL installations) off, on Sleep Hour, 22 0-23 KTP Arm, off off (ratchet arm), on (al
PAGE 28
Preliminary 2/5/02 Table B3: Sensor Information Sensor Number Sensor Text Sensor Type Sensor Group 01 02 03 04 05 06 07 08 09 10 13 14 15 16 17 18 19 20 26 Allegro
PAGE 29
Preliminary 2/5/02 Table B4: Central Station Reports Report Condition Sensor 01-MaxZones Alarm Report Types High-Level Events Low-Level Events √ √ Sensor 01-MaxZones Low Batter Sensor 01-MaxZones Tamper √ Sensor 01-MaxZones Supervisory Phone Test √ AC Power Fail CPU Low Battery Auto Phone Test Receiver Failure (or Receiver Trouble?) Receiver Jam √ √ √ Fire Panic Police Panic Auxiliary Panic √ √ √ √ √ √ Event Buffer Full System Tamper √ √ √ √ √ √ Opening report Closing Report Duress Alarm √
PAGE 30
Preliminary 2/5/02 Appendix C: Installation Menus T o e n te r P r o g r a m m in g M o d e : 8 + In s ta lle r o r 8 + D e a le r C o d e T IE R 1 M E N U S A c c o u n t 0 0 -0 0 0 P h o n e s D e v ic e s C o d e s D o w n lo a d e r T IE R 2 M E N U S O p tio n s T im e r s P r e s s a r r o w s to c o n tin u e to D e v ic e s P h o n e s P h o n e 1 P h o n e 2 N u m b e r 1 N u m b e r 2 F o rm a t C ID S IA F o rm a t C ID S IA H ig h L e v O n O ff H ig h L e v O n O ff L o w L
PAGE 31
Preliminary 2/5/02 Specifications Nominal Range: .............. 500 feet, open-air receiving range Power Requirements: .....8 VAC, 300 mA Temperature Range Storage:.............................. -30° to140° F (-34° to 60° C) Rechargeable Battery:.....4.8 VDC Rechargable NiCd Battery pack Radio Frequency: ............319.5 MHz + or - 140 kHz Allegro Operating: ......................... 32° to 122° F (0° to 49° C) Maximum Humidity: .....