User's Manual

1
Micro Wristwatch Panic Button
Installation Instructions
P
re
li
m
i
nary
9/11/01
Product Summary
The Panic Button is a wireless device designed to be used
throughout the premises for police, medical, or auxiliary
alarm activation. When the panic button is pressed, the
built-in transmitter sends a signal to the panel. Press the
molded front round cover to activate the button. The switch
inside has a tactile feel, so you can also “feel” when the but-
ton has been fully depressed. If the panic button was
pressed correctly, the LED mounted under the front cover
blinks once with each transmission sent.
The status of the battery is sent in every transmission. How-
ever, it is important to note that there is no special low bat-
tery transmission. The battery is field replaceable.
The rubber o-ring used to seal off the inner chamber ensures
that the water-resistant design helps prevent damage in case
the button gets wet.
The button has five adapters which easily fit onto the panic
button. Using these adapters, the panic button can be
mounted on the wall, worn as a belt clip, as a watch, or as a
pendant.
Figure 1. Panic Button Adapters
Installation Guidelines
Use the following guidelines when installing this button.
❑ The transmitter in the button has an open-air range of
up to 500 feet, but the installation environment may
influence this range.
Wall Mount Adapter
1. Place the wall mount adapter
on the wall at the desired
location and mark through the
mounting holes with a pencil.
2. Secure the holder to the wall
with the screws supplied. Use
the anchors supplied where
studs are not present.
3. Snap the panic button onto the four snap-on posts on
the wall mount adapter.
Belt Clip Adapter
The belt clip adapter is very easy to use. Simply snap the
panic button onto the four snap-on posts on the belt clip
adapter.
Wrist Adapter
The panic button can be worn on the wrist two different
ways. Using a plastic wrist band with spring loaded pins or
with a velcro wrist band.
❑ Plastic Wrist Band - To use the plastic wrist band,
compress the spring-loaded pins with a small screw
driver and slip into the pin slots located on the back of
the panic button. The plastic wrist band or almost any
other 18 mm watch band can be used.
❑ Velcro Wrist Band - To use the velcro wrist band, first
snap the panic button onto the four snap-on posts on the
wrist band adapter. Next, thread the band through the
slots on the ends of the adapter.
Pendant Adapter
The panic button can be worn as a pendant two different
ways. It can be worn with a necklace by using the pin-
mounted necklace adapter, or it can be worn with the rope
necklace that comes with it using the snap-on pendant
adapter.
To use the pin-mounted necklace adapter:
1. Check to make sure the necklace or chain fits through
the larger hole in the pin-mounted necklace adapter.
2. Remove one of the
spring-loaded pins
from the plastic wrist
band and insert it into
the smaller hole on the
necklace adapter.
3. Compress the spring-
loaded pins with a small screw driver and slip into the
pin slots located on the back of the panic button.
8958G10A.DSF
WALL MOUNT
ADAPTER
BELT CLIP
ADAPTER
WRIST BAND
ADAPTER
PENDANT
ADAPTER
PIN-MOUNTED
NECKLACE
ADAPTER
Wall
Mount
Adapter
Pendant
Adapter
Velcro
Wrist Band
Adapter
Belt
Clip
Adapter
Pin-Mounted
Necklace
Adapter
MOUNTING
HOLES
SNAP-ON
POSTS
S
NAP-ON
POSTS
Snap-On
Posts
Mounting
Holes
Snap-On
Posts
PIN-MOUNTED
NECKLACE
ADAPTER
SPRING-LOADED
PIN
Spring-Loaded
Pin
Pin-Mounted
Necklace
Adapter
0LFUR: ULVWZD WF K3DQLF
%XWWRQ
ITI Part No. 60-XXX
Document Number: L66-1815 Rev. A PRELIMINARY
September 2001
8958
g
07a.ds
f