User's Manual

ManualsBrandsUTC Fire & Security Americas ManualsElectronics679A-95-DWS

,7,6$:'RRU:LQGR Z

6HQVRU

ITI Part No. 60-670-95R

Installation Instructions

Product Summary

Door/Window Sensors can be installed on doors, windows,

or many other objects that open and close. The sensors

transmit signals to the Control Panel when a magnet

mounted near the sensor is moved away from or closer to

the sensor.

Installation Guidelines

Use the following guidelines for installing Door/Window

sensors.

❑ Mount the sensor on the door frame and the magnet on

the door. If the sensor is to be used on double doors,

mount the sensor on the least-used door and the magnet

on the other door.

❑ If possible, locate sensors within 100 feet of the panel.

While a transmitter may have a range of 500 feet or

more out in the open, the environment at the installa-

tion site can have a significant effect on transmitter

range. Sometimes a change in sensor location can help

overcome adverse wireless conditions.

❑ Make sure the alignment arrow on the magnet points to

the alignment mark on the sensor.

❑ Place sensors at least 5 inches above the floor to avoid

damaging them.

❑ Avoid mounting sensors in areas where they will be

exposed to moisture or where the operating tempera-

ture (10°-120°F) will be exceeded.

❑ Use spacers (not included) to keep sensors and magnets

away from metal or metallic surfaces such as foil wall-

paper.

Materials Needed

❑ #6 flathead screws

❑ Screwdriver or brad driver

The following illustrations and procedure describe how to

install the Door/Window sensor.

Figure 1. Sensor and Magnet Positions

Figure 2. Aligning the Door/Window Sensor and Mag-

net

To install Door/Window sensors:

1. Remove the sensor cover by pressing the button on the

narrow end.

2. Remove the batteries to access the mounting holes.

3. Mount the sensor base with two #6 flathead screws at

the locations shown in Figure 3. If you need to connect

Sensor

Magne

Align Arro

and Mark

Doorframe

2 - AAA Batteries

8959G16B.DS4

Document Number: 466-1559 Rev. B PRELIMINARY

December 2001

Summary of content (4 pages)

PAGE 1
ITI Part No. 60-670-95R ,7, 6$: 'RRU :LQGRZ 6HQVRU Document Number: 466-1559 Rev. B PRELIMINARY December 2001 Product Summary Installation Instructions The following illustrations and procedure describe how to install the Door/Window sensor. Door/Window Sensors can be installed on doors, windows, or many other objects that open and close. The sensors transmit signals to the Control Panel when a magnet mounted near the sensor is moved away from or closer to the sensor.
PAGE 2
Programming external switches, they should be installed at this point. Use the procedure for connecting external switches. MOUNTING HOLES 1. Open the control panel cover. 2. Enter Utility Access Code 1 or 2 using the red-numbered buttons. 3. Press Add from the Start Menu. 4. Press the Sensor/Remote button from the Main menu until you hear the location you wish to use with the sensor. 8888G01A.DS4 Figure 3. Mounting Hole Locations (Bottom View) 4. Remove the magnet from its base.
PAGE 3
Specifications If a Sensor Fails the Sensor Test If sirens do not beep when a sensor is tripped, use an ITI RF Sniffer (60-401) test tool to verify that the sensor is transmitting. Constant beeps from the RF Sniffer indicate a runaway (faulty) sensor. Replace the sensor. FCC Notices This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. To improve sensor communication, you can: 2.
PAGE 4
FCC Notices 2 2 6 6 S e co n d St r e e t No r t h | N o r t h S a i n t Pa u l M n | 55109 | 8 0 0 - 7 77 - 2 6 2 4 | w w w. i t i i .c o m © 2001 I nte r logi x,™ In c. Int er log ix is a t r ade mar k o f I nt er logi x, I nc. IT I is a r egist e re d t ra dema rk of Int er lo gix , Inc. 4 | ww w.i n t e r l o gi x se cu r i t y.