Service manual
Table Of Contents
- COVER
- CAUTION
- Safety precautions
- CONTENTS
- 1-1 Specifications
- 1-2 Handling Precautions
- 1-3 Installation
- 1-4 Maintenance mode
- 1-5 Trouble Shooting
- 1-5-1 Paper misfeed detection
- 1-5-2 Self-diagnosis
- 1-5-3 Image formation problems
- (1) No image appears (entirely white).
- (2) No image appears (entirely black).
- (3) Image is too light.
- (4) Background is visible.
- (5) A white line appears longitudinally.
- (6) A black line appears longitudinally.
- (7) A black line appears laterally.
- (8) One side of the copy image is darker than the other.
- (9) Black dots appear on the image.
- (10)Image is blurred.
- (11)The leading edge of the image is consistently misaligned with the original.
- (12)The leading edge of the image is sporadically misaligned with the original.
- (13)Paper creases.
- (14)Offset occurs.
- (15)Image is partly missing.
- (16)Fixing is poor.
- (17)Image is out of focus.
- (18)Image center does not align with the original center.
- (19)Image is not square.
- (20)Image contrast is low (carrier scattering).
- 1-5-4 Electrical problems
- (1) The machine does not operate when the main switch is turned on
- (2) The drive motor does not operate when (C200)
- (3) The scanner motor does not operate.
- (4) The toner feed motor does not operate
- (5) Cooling fan motor 1 does not operate
- (6) Cooling fan motor 2 does not operate
- (7) Cooling fan motor 3 does not operate
- (8) The drawer motor does not operate
- (9) The registration clutch does not operate
- (10) The upper paper feed clutch does not operate
- (11) The lower paper clutch does not operate
- (12) Paper feed clutch (ST) 1 does not operate
- (13) Paper feed clutch (ST) 2 does not operate
- (14) The bypass paper feed clutch does not operate
- (15) The cleaning lamp does not turn on
- (16) The exposure lamp does not turn on
- (17) The exposure lamp does not turn off
- (18) The fixing heater does not turn on (C610)
- (19) The fixing heater does not turn off
- (20) Main charging is not performed
- (21) Transfer charging is not performed
- (22) No developing bias is output
- (23) The original size is not detected
- (24) The original size is not detected correctly
- (25) The message requesting papaer to be loaded is shown when paper is present
- (26) The message requesting papaer to be loaded is shown when paper is present in the upper drawer
- (27) The message requesting papaer to be loaded is shown when paper is present in the lower drawer
- (28) The size of paper in the upper drawer is not displayed correctly
- (28) The size of paper in the upper drawer is not displayed correctly
- (29) The size of paper in the lower drawer is not displayed correctly
- (30) The printing width of the paper on the bypass is not detected correctly
- (31) A paper jam in the paper feed, paper conveying or fixing section is indicated when the main switch is turned on
- (32) The message requesting covers to be closed is displayed when the front cover, paper conveying unit and lower drawer left
- (33) Others
- 1-5-5 Mechanical problems
- 1-6 Assembly and disassembly
- 1-6-1 Precautions for assembly and disassembly
- 1-6-2 Paper feed section
- (1) Detaching and refitting the upper and lower paper feed pulleys
- (2) Detaching and refitting the bypass paper feed pulley
- (3) Detaching and refitting the left registration cleaner assembly
- (4) Detaching and refitting the right registration cleaner assembly
- (5) Detaching and refitting the bypass paper width switch
- (6) Adjustment after roller and clutch replacement
- 1-6-3 Optical section
- (1) Detaching and refitting the exposure lamp
- (2) Detaching and refitting the scanner wires
- (3) Detaching and refitting the laser scanner unit
- (4) Adjusting the skew and vertical shifting of the laser scanner unit
- (5) Detaching and refitting the ISU (reference)
- (6) Adjusting the position of the ISU (reference)
- (7) Adjusting the longitudinal squareness (reference)
- (8) Adjusting magnification of the scanner in the main scanning direction
- (9) Adjusting magnification of the scanner in the auxiliary scanning direction
- (10) Adjusting the scanner leading edge registration
- (11)Adjusting the scanner center line
- (12) Adjusting the margins for scanning an original on the contact glass
- 1-6-4 Main charging section
- 1-6-5 Drum section
- 1-6-6 Developing section
- 1-6-7 Transfer section
- 1-6-8 Cleaning section
- 1-6-9 Fixing section
- 1-7 Requirements on PCB Replacement
- 2-1 Electrical Parts Layout
- 2-2 Electrical parts layout
- 2-3 Operation of the PCBs
- 2-4 Appendixes
2AV/X
2-3-12
Terminals (CN) Voltage Remarks
2-3
20-4 20-2 0/5 V DC PM READY signal, input
20-5 20-2 0/5 V DC (pulse) PM drive clock pulse, output
21-1 21-2 0/5 V DC LDPCB HSYNC signal, input
21-3 21-2 5 V DC 5 V DC supply for LDPCB, output
21-5 21-2 0/5 V DC LDPCB ENABLE signal, output
21-6 21-2 0/5 V DC LDPCB VIDEO signal, output
21-7 21-2 0/5 V DC LDPCB S/H signal, output
22-2 22-1 0/5 V DC CCDPCB SHIFT signal, output
22-4 22-3 0/5 V DC CCDPCB CLP signal, output
22-6 22-5 0/5 V DC CCDPCB RESET signal, output
22-8 22-7 0/5 V DC (pulse) CCDPCB clock pulse, output
22-10 22-9 0/5 V DC (pulse) CCDPCB clock pulse, output
23-2 23-1 12 V DC 12 V DC supply for CCDPCB, output
23-4 23-3 0/5 V DC CCDPCB image signal (EVEN), input
23-6 23-5 0/5 V DC CCDPCB image signal (ODD), input
24-1 24-5 0/5 V DC EL on/off, output
24-2 24-5 0/5 V DC EL on/off, output
24-3 24-5 24 V DC 24 V DC supply for INPCB, output
24-4 24-5 24 V DC 24 V DC supply for INPCB, output
25-2 25-1 0/5 V DC ODSW on/off, input
25-3 25-1 5 V DC 5 V DC supply for ODSW, output
25-5 25-4 0/5 V DC SHPSW on/off, input
25-6 25-4 5 V DC 5 V DC supply for SHPSW, output
25-8 25-7 0/5 V DC 5 V DC supply for OSDS, output
25-9 25-7 5 V DC OSDS on/off, input
26-1 27-12 0/5 V DC OPCB KEY0 signal, input
26-2 27-12 0/5 V DC OPCB KEY1 signal, input
26-3 27-12 0/5 V DC OPCB KEY2 signal, input
26-4 27-12 0/5 V DC OPCB KEY3 signal, input
26-5 27-12 0/5 V DC OPCB KEY4 signal, input
26-6 27-12 0/5 V DC OPCB KEY5 signal, input
26-7 27-12 0/5 V DC OPCB KEY6 signal, input
26-8 27-12 0/5 V DC OPCB KEY7 signal, input
26-9 27-12 0/5 V DC OPCB LEDON0 signal, output
26-10 27-12 0/5 V DC OPCB LEDON1 signal, output
26-11 27-12 0/5 V DC OPCB LEDON2 signal, output
26-13 27-12 0/5 V DC OPCB LEDON4 signal, output
26-14 27-12 0/5 V DC OPCB LEDON3 signal, output
26-15 27-12 0/5 V DC (pulse) OPCB SCAN7 signal, output
26-16 27-12 0/5 V DC (pulse) OPCB SCAN6 signal, output
26-17 27-12 0/5 V DC (pulse) OPCB SCAN5 signal, output
26-18 27-12 0/5 V DC (pulse) OPCB SCAN4 signal, output
26-19 27-12 0/5 V DC (pulse) OPCB SCAN3 signal, output
26-20 27-12 0/5 V DC (pulse) OPCB SCAN2 signal, output
26-21 27-12 0/5 V DC (pulse) OPCB SCAN1 signal, output
26-22 27-12 0/5 V DC (pulse) OPCB SCAN0 signal, output
27-1 27-12 0 - 5 V DC LCD Vdd signal, output
27-2 27-12 -12-0 V DC LCD Vee signal, output
27-3 27-12 0/5 V DC (pulse) LCD UD3 signal, output
27-4 27-12 0/5 V DC (pulse) LCD UD2 signal, output
27-5 27-12 0/5 V DC (pulse) LCD UD1 signal, output
27-6 27-12 0/5 V DC (pulse) LCD UD0 signal, output
27-7 27-12 0/5 V DC (pulse) LCD CP signal, output
27-8 27-12 0/5 V DC (pulse) LCD FLM signal, output
27-9 27-12 0/5 V DC LCD LEDENB signal, output
27-10 27-12 0/5 V DC (pulse) LCD LP signal, output