XML006-K1 INSTRUCTION MANUAL For 37-75" TV If you have any questions along the way, just give us a call 1-800-460-0956 or mail to customerservice@x-mount.com.
Before getting started, let’s check below lists to make sure it is just right for you! 1 Check your TV VESA is within Min and Max size Does your TV MAX:600mm/23.62" (MIN:200mm/7.87") No? This mount is NOT compatible. MAX:400mm/15.74" (MIN:100mm/3.94") 2 No? Perfect – you may continue. (including accessories) Yes? This mount is NOT compatible. weigh MORE than 99 lbs.
-D TV INTERFACE 200mm [7.87in] 15mm [0.59in] 400mm [15.74in] 100mm [3.94in] 600mm [23.62in] WALL PLATE Ø9mm [Ø0.35in] TOP VIEW - EXTENDED SIDE VIEW - EXTENDED 411mm [16.17in] 177mm [6.97in] 285mm [11.22in] +5° 203mm [7.99in] 372mm [14.66in] 236mm [9.29in] -15° 304mm [11.97in] 435mm [17.13in] FULLY ASSEMBLED MOUNT SIDE VIEW - RETRACTED TOP VIEW - RETRACTED 697mm [27.44in] 62mm [2.45in] 429mm [16.
WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts! NOTE: Not all hardware included will be used. Parts and Hardware for STEP 1 TV Brackets Spacers TV Screws M4x12mm x4 M4x30mm M6x17mm M8x22mm x4 x4 M6x12mm x4 M6x35mm x4 2.
Parts and Hardware for STEP 2 Lag Bolt M8 Washer Wall Plate Unit x4 x4 CAUTION:Do not use in drywall or wood Level Concrete Wall Anchor 4pcs x1 Parts and Hardware for STEP 3 Extension Arm x2 Allen Key x1 End Support Extension Arm x2 M6x8mm Bolt x4 x2 M6x15mm Bolt x2 M6x8mm Bolt x4 5
1-2 Need Spacer? 1-1 Select TV Screws No, go to PAGE 7 Bracket M4 M6 Short Screw for detailed combination. Washer M8 TV back Yes, go to PAGE 7 Long Screw Bracket for detailed combination.
1-3 Attach the TV Brackets No! Screw and washer Spacer(s), screw(s) and washer(s) Tips: If you need to combine M8( c / f ) screw with 2.5mm spacer( j ), you have to remove the inner circle.
CAUTION: Avoid potential personal injury or property damage! ● Drywall covering the wall, must not exceed 5/8 in. (16 mm) ● Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm) ● Minimum horizontal space between fasteners: 16 in. (406 mm) ● Stud center must be verified 1. Locate your studs. Verify and mark the center of the stud by finding the stud edges using, a thin nail, or an edge to edge stud finder. 2.
3. Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit. IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm). Be sure to drill into the center of the studs. 4. Install wall plate using four lag bolts they are pulled firmly against the wall plate. and four washers . Tighten the lag bolts only until CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts. Go to STEP 3 on PAGE 12. 2.5"(64mm) 7/32" (5.
CAUTION: Avoid potential personal injury or property damage! ● Mount the wall plate assembly directly onto the concrete surface ● Minimum solid concrete thickness: 8 in. (203 mm) ● Minimum horizontal space between fasteners: 16 in. (406 mm) 1. Position the wall plate on the wall at your desired height. Level the wall plate and mark the hole locations. 2. Drill four pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit. IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm).
3. Insert four anchors . CAUTION: Be sure the anchors are seated flush with the concrete surface. 4. Insert wall plate using four lag bolts pulled firmly against the wall plate. and washers .Tighten the lag bolts only until they are CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts.
Please make sure you install these extension arms in right direction.
Before hanging TV, please try to pull the mount to make sure that it has been assembled on the wall tightly.
Hang TV/bracket assembly onto wall plate, wrap clips on bracket around extension arms and tighten them using bolts .
6-1 TV leveling adjustment (±3°): Loosen 4 leveling bolts on the rear of TV plate by maximum 2 turns, adjust to level, and retighten to secure.
6-2 Tilting angle adjustment (+5°/-15°)： Loosen handle and tilting bolt, adjust TV to your desired position, then tighten handle and tilting bolt.
