Low Pressure Diaphragm Pumps HYPRO ® Installation, Operation, Repair and Parts Manual Form L-1381 Rev. B Description California Proposition 65 Warning -- This product and related accessories contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Hypro low pressure diaphragm pumps are recommended for ground and low-level spraying of herbicides, pesticides, liquid fertilizers and many other hard-tohandle fluids.
Drive Options Order appropriate Shaft Adapter Kit for drive option requirements. Refer to adjoining chart for proper selection. For proper installation, refer to Page 5. 9910-D250 are supplied with a splined thru shaft. These models can be adapted for belt and pulley drive with the use of a split taper bushing (Hypro part number 31150011). Use of this bushing allows a Browning Q2 sheave to be mounted on the bushing. NOTE: Model 9910-D135 is supplied with a 1-3/8" male PTO splined shaft as standard.
Installation Diaphragm Pump Connection 1. Always mount the pump with oil sight tube in the upright position. 2. Proper selection of type and size of hose is vital to good performance: a. Use suction line of spiral wire braid reinforced suction hose to prevent collapse. Diameter of inlet hose should be at least that of the pump inlet hose barb or greater. Agitation Line Tank Shut-off b. Use only approved high pressure hose on discharge side of pump. 3.
Maintenance Instructions for All Models Maintenance Diaphragm and Valve Replacement 1. After use, flush the pump with clean water. I. Valve and O-Ring Replacement 1. Occasionally debris can cause the valves to not seat properly or damage the o-rings. To check for this problem, follow these steps. 2. Hypro diaphragm pumps come with oil in the crankcase. Hypro recommends changing oil after 40 hours of break-in operation and every three months or 500 hours, whichever comes first.
Parts List for 9910-KIT1708, 9910-KIT1710 and 9910-KIT1711 3 4 6 7 2 8 5 11 9 16 17 10 1 12 15 13 Included in KIT1710 14 9 2 10 9 9 REF. PART NO.
Control Units 3300-0082, 3300-0087 and 3300-0088 Description The 3300-0082 control unit is designed for proportional output and automatic pressure compensation of the outlet valves. When the outlet valves are turned on and off, the automatic compensation feature holds the pressure at constant value. mounting separately from the pump. They consist of a main pressure regulating valve and 3 on-off outlet valves.
Parts Illustration and List for Model 3300-0082 NOTE: When ordering parts, give QUANTITY, PART NUMBER, DESCRIPTION, and COMPLETE PUMP MODEL NUMBER. Reference numbers are used ONLY to identify parts in the drawing and are NOT to be used as order numbers. REF. PART NO.
Parts Illustrations for Models 3300-0087 and 3300-0088 44 50 24 56 71 1 3 105 57 44 50 51 52 58 117 118 61 13 48 35 4 50 24 56 34 59 13 70 109 24 102 30 55 31 41 103 32 33 53 35 44 44 22 23 44 18 19 20 21 15 16 17 14 24 L-1381 (Rev.
Parts Model List for9910-DBS-110, Models 3300-0087 9910-DBS-140 and 3300-0088 REF. PART NO.
Parts Illustrations for Models 9910-D70 and 9910-D70GR Figure 6. Parts Illustrations for Model 9910-D70 10 11 11 10 32 33 34 2 12 16 17 24 19 24 18 75 35 36 4 12 48 79 53 57 58 7 14 6 Figure 7. 9910-D70GR Gear Box Components L-1381 (Rev.
Parts List Model for9910-DBS-110, Models 9910-D70 9910-DBS-140 and 9910-D70GR REF. PART NO.
Parts Illustrations for Models 9910-D115, 9910-D115GR34 and 9910-D135 Figure 8. Parts Illustrations for Model 9910-D115 and 9910-D135 61 53 31 79 61 37 54 32 36 63 59 3 34 33 5 1 38 37 84 81 83 82 60 78 3 55 62 4 37 35 65 64 8 9 18 66 10 57 14 12 13 15 14 92 93 94 95 96 97 95 94 L-1381 (Rev. B) 91 89 101 102 103 Ref. No.
Parts List for Models Model 9910-DBS-110, 9910-D115, 9910-D115GR34 9910-DBS-140and 9910-D135 REF. PART NO.
Parts Illustrations for Model 9910-D160 16 14 43 15 7 17 1 13 18 9 19 7 60 60 8 5 6 43 10 44 55 11 40 48 47 50 49 52 57 53 2 46 51 Without air chamber 6 28 11 55 42 33 32 31 30 26 29 25 24 23 74 45 52 43 6 54 38 39 38 35 37 36 39 37 36 20 53 57 34 35 41 34 Figure 10. Parts Illustrations for Model 9910-D160 L-1381 (Rev.
Model Parts 9910-DBS-110, List for Model9910-DBS-140 9910-D160 REF. PART NO.
Parts Illustrations for Model 9910-D250 12 13 38 15 14 43 16 3 17 6 8 18 57 61 41 42 39 1 4 7 58 40 5 38 2 56 55 54 49 25 24 23A 46 22 47 32 23 48 51 38 5 29 53 52 31 30 53 52 41 9 37 37 34 10 33 Figure 11. Parts Illustration for Model 9910-D250 L-1381 (Rev.
Model Parts 9910-DBS-110, List for Model9910-DBS-140 9910-D250 REF. PART NO.
Pump Performance U.S. Units 350 GPM 13.6 11.2 11.0 10.7 10.6 RPM HP 0.33 0.73 1.20 1.71 2.18 400 RPM GPM HP 15.1 0.40 12.7 0.79 12.4 1.39 12.3 2.10 12.1 2.46 450 RPM GPM HP 16.9 0.48 14.1 0.91 13.9 1.63 13.8 2.19 13.7 2.77 500 GPM 18.4 15.6 15.2 15.1 15.0 RPM HP 0.58 1.01 1.66 2.36 3.12 550 RPM GPM HP 19.6 0.80 17.0 1.09 16.6 1.91 16.3 2.63 16.1 3.39 BAR 0 5 10 15 20 350 LPM 51.2 42.3 41.4 40.4 40.0 RPM HP 0.33 0.73 1.20 1.71 2.18 400 RPM LPM HP 57.1 0.40 47.9 0.79 46.9 1.39 46.3 2.10 45.7 2.
U.S. Units Series D160 350 RPM PSI GPM HP 0 27.9 0.61 72 26.4 1.51 145 25.4 2.48 217 24.3 3.45 290 23.6 4.50 Metric Units Series D250 Series D250 Series D160 350 RPM BAR LPM HP 0 105.3 0.61 5 99.7 1.51 10 95.7 2.48 15 91.8 3.45 20 89.1 4.50 U.S. Units 350 RPM PSI GPM HP 0 42.7 0.71 72 41.4 2.33 145 40.1 4.09 217 39.3 5.70 290 38.8 7.52 Metric Units 350 RPM BAR LPM HP 0 161.2 0.71 5 156.1 2.33 10 151.4 4.09 15 148.5 5.70 20 146.4 7.52 Pump Performance 400 RPM GPM HP 32.1 0.80 30.0 1.73 28.7 2.91 27.
Limited Warranty on Hypro/SHURflo Agricultural Pumps & Accessories Hypro/SHURflo (hereafter, “Hypro”) agricultural products are warranted to be free of defects in material and workmanship under normal use for the time periods listed below, with proof of purchase. - Pumps: one (1) year from the date of manufacture, or one (1) year of use. This limited warranty will not exceed two (2) years, in any event. - Accessories: ninety (90) days of use.
