DAX-602/802 Digital to Analog Converter 181 Bonetti Drive San Luis Obispo, CA 93401 ph: 1+ 805-549-0161 fax: 1+ 805-549-0163 www.uslinc.com 5/2013 181 Bonetti Drive San Luis Obispo, CA 93401 USA ph: +1 805-549-0161 fax: +1 805-549-0163 www.uslinc.
DAX-602/802 INSTRUCTION MANUAL Ultra Stereo Labs, Inc. DAX-602/802 INSTRUCTION MANUAL Ultra Stereo Labs, Inc. Revision History: 2/1/2009 - Original Version 9/1/2012 - Compliance Information Added; HI/VI-N Connector Changed. 5/7/2013 - Editorial updates, new rear panel for Rev. “D” depicted.
DAX-602/802 INSTRUCTION MANUAL Ultra Stereo Labs, Inc. DAX-602/802 INSTRUCTION MANUAL Ultra Stereo Labs, Inc. TABLE OF CONTENTS Warranty.......................................................................2 Safety Notices..............................................................4 Regulatory Compliance................................................5 DAX Background........................................................10 Front Panel Designations...........................................
DAX-602/802 INSTRUCTION MANUAL Ultra Stereo Labs, Inc. DAX-602/802 INSTRUCTION MANUAL Ultra Stereo Labs, Inc. Safety Notices Review the following safety precautions to avoid injury and prevent damage to this SURGXFW 7R DYRLG SRWHQWLDO ULVN XVH WKLV SURGXFW RQO\ DV VSHFL¿HG DQG RQO\ IRU WKH purpose described in the instruction manual. To Avoid Fire and Personal Injury: Use correct power supply. Use only the power supply provided.
DAX-602/802 INSTRUCTION MANUAL Ultra Stereo Labs, Inc. DAX-602/802 INSTRUCTION MANUAL Ultra Stereo Labs, Inc.
DAX-602/802 INSTRUCTION MANUAL Ultra Stereo Labs, Inc. Fournissez Ventilation Adéquate. La température dufonctionnement devrait être entre 0° C et 40° C. L’humidité devrait être 20% et 80%. La méthoderefroidissante est par convection et un ventilateur interne. Gardez les Surfaces du Produit Nettoient et Sec. Déconnectez le câble du pouvoir de la source du pouvoir avant de nettoyer. N’utilisez pas de nettoyeurs.
DAX-602/802 INSTRUCTION MANUAL Ultra Stereo Labs, Inc. 8VLQJ ,3 $XWRFRQ¿JXUDWLRQ DQG 1(7%,26 If no network with a DHCP server is available, connect a computer to the DAX using a network “crossover” cable. Some recent computers can use a standard “straight through” cable, but a crossover cable will always work. 0DQ\ FRPSXWHUV VXSSRUW ³,3 $XWRFRQ¿JXUDWLRQ´ ZKHUH WKH FRPSXWHU FKRRVHV DQ IP address in the 169.254.x.y range.
DAX-602/802 INSTRUCTION MANUAL Ultra Stereo Labs, Inc. Sicherheit-Standard Der EN 60065 Standard schreibt Sicherheit-Entwurf-Anforderungenvor, der reduzieren oder das Risiko persönlicher Verletzung zu sowohl dem Produkt-Benutzer als auch Dienst-Personal ausschließen.
DAX-602/802 INSTRUCTION MANUAL Ultra Stereo Labs, Inc. Analog Output Connector: (25 pin D sub Male) (Balanced or Unbalanced Line) Note: In Unbalanced mode the negative signal MUST be connected to ground. To minimize ground loop hum, the negative side of the output should be connected to ground at the signal desination instead of at the DAX. Twisted pair shielded cable should be used. DAX-602/802 INSTRUCTION MANUAL Ultra Stereo Labs, Inc.
DAX-602/802 INSTRUCTION MANUAL Ultra Stereo Labs, Inc. DAX Background The DAX unit was designed as a simple Digital to Analog Converter which would accept up to 10 AES/EBU conforming signals and convert them into multi-channel analog audio. There are two versions available. The DAX-802 converts 5 screen channels, 2 surrounds and the subwoofer/LFE. The DAX-602 is almost the same but does not convert LC and RC screen channels.
DAX-602/802 INSTRUCTION MANUAL Ultra Stereo Labs, Inc. DAX-602/802 INSTRUCTION MANUAL Ultra Stereo Labs, Inc. - 14 - Power Indicator - Indicates when unit is powered on. Signal Presence Indicators - indicates when signal exceeds -30dB Power Indicator - Indicates when unit is powered on. Setting up the DAX-602 Mono/Surround mode: 1) Remove the four side screws that hold on the cover. 2) Place the two jumpers in the position shown in the picture below. 3) Replace the cover.
DAX-602/802 INSTRUCTION MANUAL Ultra Stereo Labs, Inc. DAX-602/802 INSTRUCTION MANUAL Ultra Stereo Labs, Inc. Note: This connector does not exist on the DAX-602 1. Input Power - 12VDC @ 1A power supply 2. Digital Input - AES/EBU balanced line input. Both USL and DMA8 connector formats are supported. 3. Ethernet Port - For communication with the user interface. 4. Hearing Impaired / Visually Impaired - Narration (HI/VI-N) Output - Balanced or unbalanced line audio output. 5.
