User Manual: FX500 | A | IP | IPA
CONTENTS 1. FIRST STEPS Included in delivery ..........................................................................................4 Inspection/guarantee ....................................................................................4 Power supply ......................................................................................................4 Safety warnings ...............................................................................................5 2. INTRODUCTION Description.........
1. FIRST STEPS INCLUDED IN DELIVERY: 1x FEIMEX FX500 | A | IP | IPA 1x open Titanex power cable with Neutrik PowerCon plug 1x User manual IP-Version 1x high-quality 110 ohm DMX cable with Neutrik NC3FX-HD & NC3MX-HD, each 1.20 m INSPECTION/WARRANTY: Please check that the delivery is complete and the state of the goods. If the packaging and/ or parts of the delivery are damaged, please immediately inform your supplier. We recommend keeping the original packaging in case of returns.
1. FIRST STEPS SAFETY WARNINGS CAUTION! Please read the following details conscientiously before inital operation of the appliance. They contain important information about handling and servicing of the appliance. The following symbols are used to indicate important information for the product and in this user manual. CAUTION! Safety hazard. Risk of severe injury or death. CAUTION! Hazardous Voltage. Risk of lethal or severe electric shock. CAUTION! Fire hazard. CAUTION! LED light emission.
2. INTRODUCTION DESCRIPTION • Voltage range (alternating current/AC): 100V to 230V at 50-60Hz • Rated power: 110W • LED-quantity: 15x4-in-1(RGBW) • LED: 380mA • Beam angle: Standard 30° • Protection class: IP20-indoor-version / IP65-outdoor-version • Product size: 990x120x145 mm • Packaging size: 1070x160x170 mm • Weight: 5.
DMX IN DMX IN DMXOUT DMXOUT DMX IN DMX IN DMXOUT DMXOUT DMX IN DMX IN DMXOUT DMXOUT 2.
3. INSTALLATION INSTALLATIONS-REQUIREMENTS • This product can be flown or stood. • For mounting in truss (suspending or standing), special clamps (trigger-clamps, half-couplers, etc.) are necessary. These clamps are not included in delivery and must be acquired independently. • No flammable objects may be placed within a half meter radius of the appliance. • To avoid damage to the appliance, mounting and installation of the appliance should be handled by a qualified professional.
3. INSTALLATION CONNECTING THE DMX-SIGNAL-CABLE 1. Please only use high quality cable. We recommend FEIMEX Platin DMX cable. Connect the female 3-pin end of the DMX-cable to the male 3-pin input of the first appliance. DMX IN DMX OUT DMX IN DMX OUT DMX IN 2. Connect the female 3-pin cable end of the first fixture to the male 3-pin input-connector of the following appliance. Repeat this procedure until you have connected the desired number of your appliances. 3.
4. INSTRUCTIONS CONTROL-PANEL-FUNCTIONS KNOB FUNCTION MENU To exit the current menu or the current function. ENTER To select the currently shown menu or to define the currently selected value in the selected function. UP Navigates up in the menu bar and increases the numeric value within a function. DOWN Navigates down in the menu bar and decreases the numeric value within a function.
4. INSTRUCTIONS MENU FOLDER MAIN FUNCTION dMX CoLo Auto SLAV SECONDARY FUNCTION d001 R000 G000 b000 W000 S000 000~255 (0~100%) The user can combine the colours RED, GREEN, BLUE and WHITE to produce an individual colour. 00~20 AP00 CP00 SLA SP00~20 SP00~20 11CH 04CH 06CH 15CH 17CH 21CH 60CH OFF VER DIM1/2/3/4 V 2.00 oN~oFF KEY CoMP Defines the DMX start address. SP00~20 dIM C.SUM C.ID DESCRIPTION 001~512 AT00 PERS SET SELECTION AREA 01~16 01~16 Selects the strobe frequency.
4. INSTRUCTIONS SETTINGS 1. Fixture - Settings MASTER & SLAVE-MODE 1.1. Access the functions of the control panel by repeatedly pressing [MENU] until SLAV is shown. Confirm with [ENTER] until SLA shows on the display. 1.2. Press [MENU], to return to MENU. The FX500 is always in master-mode when slave-mode is not activated. Configuration of the “Master” fixture (example with an auto-program) 2.1. Press [MENU] until auto is shown and confirm with [ENTER]. 2.2.
4. INSTRUCTIONS 3. Setting the dimmer-curve 3.1. Access the functions of the control panel by repeatedly pressing [MENU] until SET is shown. Confirm with [ENTER] to access the menu item. 3.2. Select the menu item and confirm [ENTER]. 3.3. Select the desired dimmer-curve with [UP/DOWN] and confirm with [ENTER]. 3.4. Press [MENU] to return to menu. 4. Fixture-locking 4.1. Repeatedly press [MENU] until KEY ist shown and confirm with [ENTER]. 4.2.
4. INSTRUCTIONS Setting the number of fixtures to be combined 1.1. Press [MENU] until COMP is shown and confirm with [ENTER]. 1.2. Select the menu item C.SUM with [UP/DOWN] and confirm with [ENTER]. 1.3. Select between the values 01 and 16 and confirm your selection again with [ENTER]. A maximum of 16 fixtures can be combined in a group! 1.4. Press [MENU] to return to menu. INFO The number of combined fixtures on the display must not be higher than the actual number of fixtures in use.
4.
4. INSTRUCTIONS DMX 512-CONTROL-MODE 1. Setting the DMX- start address 1.1. Access the functions of the control panel by repeatedly pressing [MENU] until DMX is shown. Confirm with [ENTER] to access the menu item. 1.2. Repeatedly press [UP/DOWN] until the desired DMX-address is shown. 1.3. Press [MENU], to return to menu. 2. Fixed-colours - selecting a fixed-colour 2.1 Access the functions of the control panel by repeatedly pressing [MENU] until CoLo is shown. Confirm with [ENTER] to access the menu item.
4. INSTRUCTIONS AUTO-PROGRAMS Channel 5 selects the preset “combined auto-program“ (AP 1 - 50). Channel 6 selects the preset ”combined cartoon effects” (CP 1 - 25). Channel 9 selects the preset auto-program (1-50). If an auto-program is activated, auto-speed can be varied with channel 10. Channel 9 has priority over channels 2 to 8. Channel 5 has priority over channels 2 to 6. Channel 6 has priority over channels 2 to 4.
4. INSTRUCTIONS 6 Channels Channel 1 2 3 4 5 6 Value 000~255 000~255 000~255 000~255 000~005 006~255 000~005 006~255 Description Red Green Blue White No function Strobe / auto-speed No function AUTO-programm (AT01-50) Channel 6 has priority over channels 1 to 5.
4. ANLEITUNG 11 Channels Channel 1. Dimmer 2. Red 3. Green 4. Blue 5. White 6. Macro colour-control 7. Strobe 8. Module Selection 9. Auto 10. 11.
4. INSTRUCTIONS 17 Channels Channel 1 LED 1 2 LED 2 3 LED 3 4 LED 4 5 LED 5 6 LED 6 7 LED 7 8 LED 8 9 LED 9 10 LED 10 11 LED 11 12 LED 12 13 LED 13 14 LED 14 15 LED 15 16. Strobe 17.
4.
4. INSTRUCTIONS 60 Channels Channel 1 LED 1 2 LED 1 3 LED 1 4 LED 1 5 LED 2 ... 57 LED 15 58 LED 15 59 LED 15 60 LED 15 Value 000~255 000~255 000~255 000~255 000~255 ... 000~255 000~255 000~255 000~255 Description red (0~100%) green (0~100%) blue (0~100%) white (0~100%) red (0~100%) ... red (0~100%) green (0~100%) blue (0~100%) white (0~100%) Master dimmer Channel 1 controls the intensity of the currently projected colour.
4. INSTRUCTIONS Auto & custom program • Channel 8 selects the current auto- & custom-program [1-10]. • If auto- & custom-program are activated, you can chose the desired step- and transition-time with channels 2 and 3. • Channel 8 has priority over channels 2-7. Dimmer-speed • Channel 10 is for selecting the dimmer-mode and dimmer-speed. • If channel 10 is not used, RGBW and master-dimmer are linear. • The dimmer-modes 1, 2, 3 and 4 describe the different speeds of non-linear dimmer-curves.
5. APPENDIX SERVICE / SETTINGS Problem(s) Possible solution(s) Clean the appliance regularly to avoid such faults. This appliance is convection cooled, which means that the surface must be keep clean and clear of foreign objects to make adequate cooling possible. One or more LEDs don‘t light up An LED may be defect which leads to an open circuit. Therefor, all LEDs of a single module fail. This does not mean all LEDs are damaged. The circuit is switched in line.
5. APPENDIX Problem(s) Possible Solution(s) Only use DMX-cable. Signal loss Install an end-plug with 120 ohm capacity. Important! Keep DMX-cables away from power cables and black light. COLOR-CON Controller doesn‘t function or doesn‘t function properly StandAlone The display only shows: #### Make sure the connection to the appliance is in order. This appliance must be operated in the correct mode to have CONTACT with the COLOR-CON controller.
Contact FEIMEX Ltd. Unit 107 The Workstation 43 Lyndhurst Terrace Central Hong Kong T +49 (0)40 468 991 790 office@feimex.com www.feimex.com FX500 – LED Bar 4in1 | IP65 FX500 – Specifications Optical system Optics fixed optical systems Beam angle 30° LED light sources LEDs 15 x 4 in 1 multicolour LEDs Colours 15 x red, 15 x green, 15 x blue, 15 x white Driver current 350 mA Service life of LEDs ~ 50.
CONTACT FEIMEX Ltd. Unit 701 The Workstation 43 Lyndhurst Terrace Central Hong Kong T +49 (0)40 468 991 790 office@feimex.com www.feimex.
