Wireless Starter Kit 802.11g 54Mbps Router 802.11g 54Mbps USB Adapter Installation Guide Guide d'installation Installationsanleitung Guida all'installazione rapida Guía breve de instalación Beknopte installatiegids R24.0496.00 Downloaded from www.Manualslib.
Downloaded from www.Manualslib.
English 802.11g 54Mbps Router Installation .......................................................... 1 802.11g 54Mbps USB Adapter Installation................................................. 5 Troubleshooting and Support.................................................................... 9 Downloaded from www.Manualslib.
Downloaded from www.Manualslib.
USR5470 Package Contents USR5462 802.11g 54Mbps Router 19VAC Power Supply Installation Guide One (1) Ethernet cable USR5422 54Mbps USB Adapter Installation CD-ROM 802.11g 54Mbps Router Installation Prepare for Installation Note: It is important that you have your serial number written down before you install the 802.11g 54Mbps Router. You can find your serial number on the bottom label of the 802.11g 54Mbps Router.
Step Two: Connect your 802.11g 54Mbps Router to your computer and connect the power supply Connect one end of the supplied Ethernet cable to your computer’s Ethernet adapter. Connect the other end to one of the LAN ports on the 802.11g 54Mbps Router. Turn on your cable or DSL modem. Connect the included power adapter to the power socket on the 802.11g 54Mbps Router. Plug the power adapter into a standard power outlet. Turn on your computer.
1. Launch a Web browser. In the location or address line of your Web browser, type http://192.168.2.1 to access the Web User Interface. After the connection is established, you will see the Web User Interface. The default password is admin. Click Login. When you access the Web User Interface, click the Setup Wizard. Note: If you are prompted to connect to the Internet, you may need to select Try Again or Connect, depending on your Internet browser. 2. 3. Select your Time Zone and then click Next.
Note: Refer to the “Configuring the 802.11g 54Mbps Router” section in the User Guide on the Installation CD-ROM for more detailed configuration information. Contact your ISP if you have any questions about your WAN type or your connection information. The installation procedure for the 802.11g 54Mbps Router is now complete. Proceed to the Installation procedure for the 802.11g 54Mbps USB Adapter.
802.11g 54Mbps USB Adapter Installation Prepare for Installation ATTENTION: You must install your software and drivers before you physically connect the 802.11g 54Mbps USB Adapter. Model Number Serial Number USR5422 Note: For the most updated information, visit: http://www.usr.com/support Turn on your desktop or laptop computer. Type your password if you are prompted to do so. Note: Be sure to find out what letter your CD-ROM drive uses before you begin installing your new product.
your preferred language. Read the license agreement and click Yes. Select the 802.11g 54Mbps USB Adapter and then click Software. Click Wireless USB Adapter Utility and Drivers. Follow the on-screen instructions to finish the installation procedure. If you are prompted, restart your computer and continue to follow the on-screen instructions. Step Two: Install the 802.11g 54Mbps USB Adapter to your computer. When you are prompted, insert the 802.
*Note: You may receive a “Digital Signature Not Found” or “Windows Logo testing” screen. Click Yes or Continue Anyway. U.S. Robotics has thoroughly tested this driver in conjunction with the supported hardware and has verified compatibility with Windows 2000, Me, and XP. Because U.S. Robotics wants its customers to take full advantage of the network adapter’s functionality, it has made the drivers available. Note: If you are prompted at any time for your Windows Operating System CD-ROM, remove the U.S.
Congratulations! You have finished installing the 802.11g 54Mbps USB Adapter and the 802.11g 54Mbps Router. You should now have shared Internet access through the 802.11g 54Mbps Router. For troubleshooting and technical support information, refer to the Troubleshooting section in this Guide or to the User Guide on the U.S. Robotics Installation CD-ROM. Register your products • At the Installation CD-ROM interface, click the Support link. Click Product Registration and then click http://www.usr.
Troubleshooting and Support If you have any difficulties connecting to the 802.11g 54Mbps Router, check the following top three issues and see if they apply to your situation. • If you are attempting to create a wireless connection but cannot connect to the 802.11g 54Mbps Router, make sure each wireless card is set to Infrastructure mode. If the wireless cards are set to 802.11g Ad hoc mode, you will not be able to connect to the 802.11g 54Mbps Router.
Direct connection to the Internet and click OK. I am no longer able to access the Internet through the 802.11g 54Mbps Router. Possible Solution: Make sure that the power cord and all the Ethernet cables are connected correctly. This includes the cables connecting the 802.11g 54Mbps Router, the modem, and all the computers. Possible Solution: Make sure that your computer is using an IP address that is within the default range of 192.168.2.xxx. Make sure the address of the subnet mask is 255.255.255.0.
My computer does not recognise the wireless function of the 802.11g 54Mbps Router after I changed the settings. Possible Solution: Ensure that you are connecting to the correct 802.11g 54Mbps Router by verifying the correct MAC address. Ensure that the correct passphrase and encryption option is being used. If you changed the settings in the configuration of the 802.11g 54Mbps Router, you must also change the settings of every Wireless adapter attached to this network.
Try performing the ping procedure to make sure you can connect with different areas of the wireless network and the internet. If at any time during the ping procedure you do not receive a return message for a successful ping, this means that you cannot connect to that IP address. After you have made the corrections, continue with the ping procedure. 1 Click Windows Start and then click Run. In the Run dialog box, Windows 98 and Me users should type command and click OK.
different letter, type that letter in place of “D”) and click OK. I accidentally clicked Cancel during the installation procedure. Possible Solution: Remove and reinsert the U.S. Robotics Installation CD-ROM into your CD-ROM drive. Repeat the installation procedure of the software before you install any hardware. My computer does not recognise the 802.11g 54Mbps USB Adapter. Possible Solution: The 802.11g 54Mbps USB Adapter may not be properly connected. Make sure the 802.
Are You Still Having Problems? 1. Go to the User Guide on the Installation CD-ROM. More configuration and troubleshooting information is available in the User Guide on the Installation CD-ROM. 2. Go to the Support section of the U.S. Robotics Web site at www.usr.com Many of the most common difficulties users experience have been addressed in the FAQ and Troubleshooting Web pages for your specific product. The product number for the 802.11g 54Mbps USB Adapter is 5422. The product number for the 802.
Downloaded from www.Manualslib.
Printed in China Downloaded from www.Manualslib.
