USB 9640 5-Channel LED PAR Introduction Thank you very much for purchasing the USB 9640, our 5-channel LED Par that can work in AUTO, AUDIO and DMX mode. To assure the reliable performance it is designed for, please read the instructions in this manual thoroughly and carefully before application.
USB 9640 5-Channel LED PAR Unpacking The USB 9640 has been thoroughly tested and shipped in perfect operating condition. Check the shipping carton carefully for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for damage and be sure all accessories necessary to operate the fixture have arrived intact. In case damage has been found or parts are missing, please contact the sales person for further instructions.
USB 9640 5-Channel LED PAR Panel review 1. LED indicator 2. Dipswitches 3. Microphone 5. Power input 6. DMX in 7. DMX out 4. Fuse Installation and operation Mounting The fixture can be mounted overhead by a clamp or against a flat surface by the bracket it has. When you mount overhead, you can connect its bracket with the clamp through the center hole. Verify the structure can hold 10 times the weight of all installed fixtures. Always use a safety cable or chain as a assistant attachment.
USB 9640 5-Channel LED PAR AC power The fixture’s mains lead may require a grounding-type cord cap that fits your power distribution cable or outlet. Consult a qualified electrician if you have any doubts about proper installation. WARNING: For protection from dangerous electric shock, the fixture must be grounded (earthed). The AC mains power supply shall have overload and ground-fault protection.
USB 9640 5-Channel LED PAR Connection of DMX Connect the provided DMX XLR cable to the female 3-pin XLR output of your controller and the other side to the male 3-pin XLR input of the fixture (please refer to the figure “Installation and Operation” below). You must chain multiple fixtures together through serial linking, never split your DMX connections unless you are using a splitter/signal amplifier.
USB 9640 5-Channel LED PAR Operation Instructions Brief function chart Switch #1 Function DXM #3 #4 #5 #6 #7 #8 #9 #10 Set DMX address (see DMX address chart for details) Slave Master #2 X X X X X X Fade Choose program via Choose speed via and switch switch Auto program Auto chart for details) Sound 1~3 (See choose 4~6 （ See 1 X X X 1 1 X 0 0 0 X 0 0 speed choose chart for details） X X X X X 1 0 Notes: In sound active mode: No fade; Run to sound; Choos
USB 9640 5-Channel LED PAR Modes Auto mode When dipswitches #9 & #10 are both set at OFF, the fixture works in Auto mode.
USB 9640 5-Channel LED PAR When dipswitch #10 is set at ON, the fixture works in DMX mode. By various combining the Dipswitches #1 to #9 you can set the address ranging from 1 to 512. At this moment, the fixtures can be controlled by DMX controller or another fixture that has been designated as Auto or Sound Active mode with 5 channels receiving the data controlling the Red, Green, Blue, brightness and strobe rate output of the fixture respectively.
USB 9640 5-Channel LED PAR Maintenance and cleaning Please refer to the following points during the normal inspection: A. Be sure all screws and fasteners are securely tightened at all times. Lose screws may cause unexpected damage or injury. B. Electric power supply cables must not show any damage or frayed spots.
USB 9640 5-Channel LED PAR Appendix DMX address chart #9 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 #8 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 #7 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 #6 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 32 64 96 128 160 192 224 256 288 320 352 384 416 448 480 SWITCH SET 0 = OFF 1 = ON #1 #2 #3 #4 #5 0 0 0 0 0 1 0 0 0 0 1 33 65 97 129 161 193 225 257 289 321 353 385 417 449 481 0 1 0 0 0 2 34 66
