Model # S UBRTG01-1017, UB03EC-1017E Manual Version #02
13 13
INTRODUCTION for must
TRAMPOLINE GUIDELINES 5
24 ft
TRAMPOLINE PARTS LIST FOR UBRTG01-1017 A B C UBRPTR1-1017 2 UBRPTR2-1017 2 UBRPTR3-1017 2 C1 UBRPCT1-1017 2 C2 UBRPCT2-1017 2 TOP RAIL A TOP RAIL B CORNER TUBE D LEG EXTENSION UBRPLE-1017 10 E LEG BASE UBRPL1-1017 4 F JUMPING MAT UBRPM-1017 1 G COVER PADS UBRPP-1017 1 H SPRINGS UBHWD-SP-7.
Frame assembly installation for model UBRTG01-1017 B2 B1 45.3 B2 44.88 B1 44.88 45.3 E D Attach the leg extensions to the leg base and tightly secure together with screws and washers Part #J and K. Continue doing the same to all 4 leg bases. 2. Connect the middle leg supports to the legs. O P Connect Part #P and Part #O together. Once it is attached, connect it to the legs by inserting it between part #D leg extensions.
5. Assemble frame parts B1 and B2 with the 4 legs. Lay out the parts as shown in the figure. Connect the B1 and B2 and place it onto the leg bases as shown in the figure below. A B1 D P B2 D O B2 E N B1 A P Q E P D O E O N E Note: 1. The Part #A goes on the long side of the trampoline - the 17 ft side. 2. Make sure that all screw holes that connects the B rails to the legs are facing the inside of the frame. C1 6. Attach all the corners.
1. Layout the Trampoline Mat inside the frame. 2. Connect all 4 corners spring to corner top rail.
The safety pad has a few sets of strings with S shaped hooks at the end, all around the pad. Attach the S shaped hooks to the V-rings of the mat. Attach the hooks from underneath the how to attach it correctly.
ENCLOSURE PARTS LIST 1017 A PLASTIC CAP ON THE HOLE B UPPER POLE WITH FOAM C LOWER POLE WITH FOAM UBRPPC-814,915,1017 10 UBRPUP-814,915,1017 10 UBRPLP-814,915,1017 10 UBRPFG3-1017 2 UBRPFG1-1017 8 UBRPFG2-1017 6 38.2’’ C1 C2 39.4’’ 26’’ D FIBERGLASS ROAD 39.4’’ 33.
Connect the lower poles to the upper poles, connect it to the straighter part of the upper pole. Secure it together with screws at the point where it connects. Make sure the EPE foams are covering the poles. D2 Connect the fiber glass pieces together, using 5 pcs of fiber glass to make the long line, and 3 pcs to make the short line. Refer to the figure at the left side to see which fiberglass pieces to use when assembling it together.
Insert the fiber glass into the the sleeve of the safety net. Long fiberglass for long side, short for shorter side as explained in the previous step. After inserting the fiber glass into the sleeve of the enclosure net, both the long side and short side, connect the shorter side to the longer side with the corner pieces - Part #J. (This step should be done while the net is laid out on the trampoline jumping mat you will only attach it afterwards to the poles. 9.
11. You can skip step 10 and connect the net to the V-rings with the clips. We always recommend to use the ropes for extra stability. 12. Your trampoline now looks like this. Proceed to Testing the Trampoline section of this manual before jumping on the trampoline.
TESTING THE TRAMPOLINE 17
FUNDAMENTAL BOUNCES TECHNIQUES 18
Ladder UBL3S-42-G Ladder with Flat Steps UBLBFS3-42 Trampoline Shoe Bag UBSHB-3 Trampoline Anchor Kit (Set of 4) UBHWD-AK-4 Deep Fastening Spiraled Anchor Kit- Set Of 4 UBHWD-AKB-4 Trampoline Spring Pull Tool (T-Hook) UBHWD-TH Upper bounce Trampoline Jumping Skate UB-TJB Springs UBHWD-SP-7-15 Economy Trampoline Weather Protection Cover, Fits for 9 x 15 FT. Rectangular Frames -Black UBWCRTG-159-BK 44 Inch Trampoline Pole Foam sleeves, fits for 1.5” Diameter Pole - Set of 12 - Blue UBFS44-1.
