Installation and Operation Manual
Table Of Contents
- Uponor Smatrix Wave PULSE
- Table of contents
- 1 Copyright and disclaimer
- 2 Preface
- 3 Uponor Smatrix Wave PULSE system description
- 3.1 System overview
- 3.2 Example of a system
- 3.3 Uponor Smatrix Wave PULSE components
- 3.4 Accessories
- 3.5 Functions
- 4 Install Uponor Smatrix Wave PULSE
- 5 Install Uponor Smatrix Wave PULSE room controller
- 5.1 Placement of room controller
- 5.2 Connect optional slave module
- 5.3 Attach room controller to the wall
- 5.4 Install room controller antenna
- 5.5 Install communication module
- 5.6 Connect actuators to room controller
- 5.7 Connect electrical underfloor heating
- 5.8 Connect input to room controller GPI
- 5.9 Connect output to room controller relays
- 5.10 Connect room controller to AC power
- 5.11 Test actuators
- 6 Install Uponor Smatrix Wave room thermostat
- 6.1 Uponor Smatrix Wave T-161
- 6.2 Uponor Smatrix Wave T-163
- 6.6 Uponor Smatrix Wave T-169
- 9 Install Uponor Smatrix Wave relay module
- 9.1 Placement of relay module
- 9.2 Attach relay module to the wall
- 9.3 Connect output to relay module
- 9.4 Register relay module to room controller
- 9.5 Use relay module to connect fan coils
- 9.6 Use relay module for time delayed two stage additional cooling (requires communication module)
- 10 Install another Uponor Smatrix room controller in the system
- 11 Finishing installation
- 12 Operate Uponor Smatrix Wave PULSE room controller
- 12.1 Principle of operation
- 12.2 Normal operation without optional scheduling programs
- 12.3 Operation with scheduling programs
- 12.4 Run mode
- 12.5 Room controller LEDs
- 12.6 Reset the controller
- 12.7 Unregister room controller channels
- 13 Operate Uponor Smatrix PULSE communication module
- 14 Operate Uponor Smatrix Wave thermostats
- 16 Maintenance
- 17 Troubleshooting
- 17.1 General
- Fluctuating floor temperature
- The room is too cold (or too warm in cooling mode)
- Thermostat setpoint is too low
- The temperature displayed on the thermostat changes after the thermostat is moved
- Installation report and room controller/channel numbering on the thermostat label doesn't match
- Installation report and room controller/channel numbering on the thermostatic head label doesn't match
- White indicator cannot be seen in window of an actuator
- Setpoint temperature displayed in the room information menu is lower than the temperature set on the thermostat
- ECO mode
- The room is too warm (or too cold in cooling mode)
- The floor is cold
- All rooms are cold (or warm in cooling mode)
- Disturbing noise from the pump at the same time every week
- No communication
- Communication failure between the room controllers
- 17.2 Troubleshooting after installation
- 17.3 Digital thermostat alarms/problems
- 17.4 Analogue thermostat alarms/problems
- 17.5 Thermostatic head alarms/problems
- The text “bAt” is shown in the display
- The text “POS” is shown in the display
- The display is off
- Radio transmission icon is displayed but the signals are received only when the thermostatic head is close to the antenna
- No radio transmission icon is displayed on thermostatic head screen when buttons are pressed
- 17.6 Communication module alarms/problems
- Alarms shown in Uponor Smatrix PULSE app
- The communication module has lost communication with Uponor cloud services
- The communication module has re-established communication with Uponor cloud services
- Software update failed
- Thermostatic head valve position error
- Floor temperature limit reached
- Faulty temperature sensor
- Faulty external temperature sensor
- Faulty relative humidity sensor
- Faulty Comfort/ECO switch
- Relative humidity sensor limit
- Faulty outdoor temperature sensor
- Faulty heating/cooling supply sensor
- External heating/cooling switch lost
- General systems alarm
- High supply temperature
- Low supply temperature
- Thermostat tamper alarm
- Low average temperature
- Relay module lost
- The communication module does not start
- Bad Wi-Fi connection
- Alarms shown in Uponor Smatrix PULSE app
- 17.7 Room controller alarms/problems
- 17.8 Contact the installer
- 17.9 Installer instructions
- 17.1 General
- 18 Technical data
10.5 Room controller LEDs
If the Uponor Smatrix PULSE app (requires communication module)
is not used, it is recommended to occasionally check the power LED
on the room controller for alarms. The power LED flashes
continuously for general alarms. Determine which thermostats are
issuing alarms by removing the cover. If a channel LED is indicating
an error, check the function and batteries of the registered
thermostat.
The room controller power LED is on (green) during normal
operation.
All the channel LEDs are off when there is no current or waiting
actuator activity. The LEDs turn on when the corresponding actuators
are activated or start flashing when they are awaiting activation.
Up to eight actuators in six rooms can be in the opening process at
the same time. If a slave module is installed, the LEDs of the seventh
and subsequent actuators flash while they are waiting for the
previous actuators to be fully open.
AB
CD0000117
Item Description
A Power LED
B Channel LEDs
Run mode
Power LED Status
Green, fixed Room controller is powered on
Red,
flashing
A problem has occurred, such as
• Loss of radio transmission from a thermostat for
more than 1 hours
Channel
LED
Status
Red, fixed Activated actuator
Red,
flashing
• Channel waiting its turn to be activated
•
Thermostat communication error or low battery
indication
• Tamper alarm (public thermostat)
Off No heating, or cooling, demand
Registration mode
Power LED Status
Red, fixed Room controller is in thermostat registration mode
Red,
flashing
Selector pointing at system device channel
Red,
flashing
slowly
Room controller is in system device registration mode
Channel
LED
Status
Red, fixed Thermostat registered but with communication errors
Green, fixed Thermostat registered and communication is OK
Red,
flashing
Selector pointing at channel
Green,
flashing
Channel selected to be registered
Off Selector not pointing at channel, nor registered
Forced mode
Channel
LED
Status
Red, fixed Activated actuator
Red,
flashing
Selector pointing at channel
Off Selector not pointing at channel, nor activated
54
|
Uponor Smatrix Wave PULSE
|
Installation and operation manual