Installation and Operation Manual
Table Of Contents
- Uponor Smatrix Wave PULSE
- Table of contents
- 1 Copyright and disclaimer
- 2 Preface
- 3 Uponor Smatrix Wave PULSE system description
- 3.1 System overview
- 3.2 Example of a system
- 3.3 Uponor Smatrix Wave PULSE components
- 3.4 Accessories
- 3.5 Functions
- 4 Install Uponor Smatrix Wave PULSE
- 5 Install Uponor Smatrix Wave PULSE room controller
- 5.1 Placement of room controller
- 5.2 Connect optional slave module
- 5.3 Attach room controller to the wall
- 5.4 Install room controller antenna
- 5.5 Install communication module
- 5.6 Connect actuators to room controller
- 5.7 Connect electrical underfloor heating
- 5.8 Connect input to room controller GPI
- 5.9 Connect output to room controller relays
- 5.10 Connect room controller to AC power
- 5.11 Test actuators
- 6 Install Uponor Smatrix Wave room thermostat
- 6.1 Uponor Smatrix Wave T-161
- 6.2 Uponor Smatrix Wave T-163
- 6.6 Uponor Smatrix Wave T-169
- 9 Install Uponor Smatrix Wave relay module
- 9.1 Placement of relay module
- 9.2 Attach relay module to the wall
- 9.3 Connect output to relay module
- 9.4 Register relay module to room controller
- 9.5 Use relay module to connect fan coils
- 9.6 Use relay module for time delayed two stage additional cooling (requires communication module)
- 10 Install another Uponor Smatrix room controller in the system
- 11 Finishing installation
- 12 Operate Uponor Smatrix Wave PULSE room controller
- 12.1 Principle of operation
- 12.2 Normal operation without optional scheduling programs
- 12.3 Operation with scheduling programs
- 12.4 Run mode
- 12.5 Room controller LEDs
- 12.6 Reset the controller
- 12.7 Unregister room controller channels
- 13 Operate Uponor Smatrix PULSE communication module
- 14 Operate Uponor Smatrix Wave thermostats
- 16 Maintenance
- 17 Troubleshooting
- 17.1 General
- Fluctuating floor temperature
- The room is too cold (or too warm in cooling mode)
- Thermostat setpoint is too low
- The temperature displayed on the thermostat changes after the thermostat is moved
- Installation report and room controller/channel numbering on the thermostat label doesn't match
- Installation report and room controller/channel numbering on the thermostatic head label doesn't match
- White indicator cannot be seen in window of an actuator
- Setpoint temperature displayed in the room information menu is lower than the temperature set on the thermostat
- ECO mode
- The room is too warm (or too cold in cooling mode)
- The floor is cold
- All rooms are cold (or warm in cooling mode)
- Disturbing noise from the pump at the same time every week
- No communication
- Communication failure between the room controllers
- 17.2 Troubleshooting after installation
- 17.3 Digital thermostat alarms/problems
- 17.4 Analogue thermostat alarms/problems
- 17.5 Thermostatic head alarms/problems
- The text “bAt” is shown in the display
- The text “POS” is shown in the display
- The display is off
- Radio transmission icon is displayed but the signals are received only when the thermostatic head is close to the antenna
- No radio transmission icon is displayed on thermostatic head screen when buttons are pressed
- 17.6 Communication module alarms/problems
- Alarms shown in Uponor Smatrix PULSE app
- The communication module has lost communication with Uponor cloud services
- The communication module has re-established communication with Uponor cloud services
- Software update failed
- Thermostatic head valve position error
- Floor temperature limit reached
- Faulty temperature sensor
- Faulty external temperature sensor
- Faulty relative humidity sensor
- Faulty Comfort/ECO switch
- Relative humidity sensor limit
- Faulty outdoor temperature sensor
- Faulty heating/cooling supply sensor
- External heating/cooling switch lost
- General systems alarm
- High supply temperature
- Low supply temperature
- Thermostat tamper alarm
- Low average temperature
- Relay module lost
- The communication module does not start
- Bad Wi-Fi connection
- Alarms shown in Uponor Smatrix PULSE app
- 17.7 Room controller alarms/problems
- 17.8 Contact the installer
- 17.9 Installer instructions
- 17.1 General
- 18 Technical data
6HOHFWFKDQQHO
6,
8VHEXWWRQVRU!WRPRYHWKHSRLQWHU/('IODVKHVUHGWRFKDQQHO
/RFNVHOHFWHGFKDQQHO
6,
3UHVVWKH2.EXWWRQWRVHOHFWWKHFKDQQHOIRUUHJLVWUDWLRQ7KH/('
IRUWKHVHOHFWHGFKDQQHOVWDUWVIODVKLQJJUHHQ
/RFDWHVXEURRPFRQWUROOHU
1RWH
7KHURRPFRQWUROOHUZLOOWLPHRXWDIWHUDERXWPLQXWHV
RILQDFWLYLW\DQGUHYHUWWRQRUPDORSHUDWLRQ7KHWLPHUZLOO
EHUHVHWZKHQDEXWWRQLVSUHVVHGRULIDGHYLFHKDVEHHQ
UHJLVWHUHGWRLW
/RFDWHWKHVXEURRPFRQWUROOHUDQGORFNFKDQQHOLQV\VWHPGHYLFH
UHJLVWUDWLRQPRGHVHHVWHSVWKURXJK
5HJLVWHUVXEURRPFRQWUROOHU
6,
$
%
1RWH
7KHURRPFRQWUROOHUZLOOWLPHRXWDIWHUDERXWPLQXWHV
RILQDFWLYLW\DQGUHYHUWWRQRUPDORSHUDWLRQ7KHWLPHUZLOO
EHUHVHWZKHQDEXWWRQLVSUHVVHGRULIDGHYLFHKDVEHHQ
UHJLVWHUHGWRLW
3UHVVWKH2.EXWWRQRQWKHVXEURRPFRQWUROOHU$
&KDQQHO/('RQERWKWKHPDVWHU%DQGVXE$URRPFRQWUROOHUV
WXUQVIL[HGJUHHQDQGWKHUHJLVWUDWLRQLVFRPSOHWH
7KHQH[WVXEURRPFRQWUROOHUFDQEHUHJLVWHUHGZLWKLQPLQXWHV
ZLWKRXWWKHQHHGWRDFWLYDWHFKDQQHORQWKHPDVWHUURRPFRQWUROOHU
DJDLQ%XWLIUHJLVWUDWLRQIHHGEDFNIURPWKHPDVWHUURRPFRQWUROOHULV
UHTXHVWHGWKHIXOOSURFHVVFDQVWDUWIURPWKHEHJLQQLQJDJDLQZLWKRXW
RYHUZULWLQJWKHILUVWVXEURRPFRQWUROOHUUHJLVWUDWLRQ
([LWUHJLVWUDWLRQPRGH
V
6,
3UHVVDQGKROGWKH2.EXWWRQRQWKHURRPFRQWUROOHUXQWLOWKHJUHHQ
/('VWXUQRIIWRHQGUHJLVWUDWLRQDQGUHWXUQWRUXQPRGH
7RXQUHJLVWHUDOUHDG\UHJLVWHUHGVXEURRPFRQWUROOHUVHHUnregister
room controller channels, Page 77
8SRQRU6PDWUL[:DYH38/6(
_
,QVWDOODWLRQDQGRSHUDWLRQPDQXDO
_
51