User Guide
36 l uponorengineering.com
ow
1
70% GREATER
29% LARGER I.D.
1
When comparing 1" F1960 EP with F2159 plastic ttings.
Uponor ProPEX cold-expansion fitting Standard insert (crimp) fitting
ASTM F1960 brass ASTM F1960 EP ASTM F1807 brass ASTM F2159 plastic
A
Flow path
½"
0.112 sq. inches
2.8 gpm @ 8 ft./sec.
4.2 gpm @ 12 ft./sec.
0.116 sq. inches
2.9 gpm @ 8 ft./sec.
4.4 gpm @ 12 ft./sec.
0.096 sq. inches
2.4 gpm @ 8 ft./sec.
3.6 gpm @ 12 ft./sec.
0.078 sq. inches
1.9 gpm @ 8 ft./sec.
2.9 gpm @ 12 ft./sec.
¾"
0.278 sq. inches
6.9 gpm @ 8 ft./sec.
10.4 gpm @ 12 ft./sec.
0.273 sq. inches
6.8 gpm @ 8 ft./sec.
10.2 gpm @ 12 ft./sec.
0.221 sq. inches
5.5 gpm @ 8 ft./sec.
8.3 gpm @ 12 ft.sec.
0.166 sq. inches
4.1 gpm @ 8 ft./sec.
6.2 gpm @ 12 ft./sec.
1"
0.496 sq. inches
12.4 gpm @ 8 ft./sec.
18.6 gpm @ 12 ft./sec.
0.488 sq. inches
12.2 gpm @ 8 ft./sec.
18.2 gpm @ 12 ft./sec.
0.396 sq. inches
9.9 gpm @ 8 ft./sec.
14.8 gpm @ 12 ft./sec.
0.292 sq. inches
7.3 gpm @ 8 ft./sec.
10.9 gpm @ 12 ft./sec.
1¼"
0.724 sq. inches
21.8 gpm @ 8 ft./sec.
32.6 gpm @ 12 ft./sec.
0.739 sq. inches
18.4 gpm @ 8 ft./sec.
27.6 gpm @ 12 ft./sec.
0.595 sq. inches
14.8 gpm @ 8 ft./sec.
22.2 gpm @ 12 ft./sec.
Not available
1½"
0.923 sq. inches
23.0 gpm @ 8 ft./sec.
34.5 gpm @ 12 ft./sec.
0.923 sq. inches
23.0 gpm @ 8 ft./sec.
34.5 gpm @ 12 ft./sec.
0.817 sq. inches
20.4 gpm @ 8 ft./sec.
30.6 gpm @ 12 ft./sec.
Not available
2"
1.877 sq. inches
47.1 gpm @ 8 ft./sec.
70.6 gpm @ 12 ft./sec.
1.730 sq. inches
43.1 gpm @ 8 ft./sec.
64.7 gpm @ 12 ft./sec.
1.463 sq. inches
36.5 gpm @ 8 ft./sec.
54.7 gpm @ 12 ft./sec.
Not available
2½"
3.110 sq. inches
77.6 gpm @ 8 ft./sec.
116.3 gpm @ 12 ft./sec.
2.688 sq. inches
67.0 gpm @ 8 ft./sec.
100.6 gpm @ 12 ft./sec.
Not available Not available
3"
4.562 sq. inches
113.8 gpm @ 8 ft./sec.
170.6 gpm @ 12 ft./sec.
3.871 sq. inches
96.5 gpm @ 8 ft./sec.
144.8 gpm @ 12 ft./sec.
Not available Not available
B
Minimum
internal
diameter
½" 0.378" 0.385" 0.350" 0.315"
¾" 0.595" 0.590" 0.530" 0.460"
1" 0.795" 0.788" 0.710" 0.610"
1¼" 0.960" 0.970" 0.870" Not available
1½" 1.084" 1.084" 1.020" Not available
2" 1.550" 1.484" 1.365" Not available
2½" 1.990" 1.850" Not available Not available
3" 2.410" 2.220" Not available Not available
Table 4-2: Uponor ProPEX ttings vs. standard insert (crimp) ttings
Note: Refer to Table C-1 in Appendix C for an equivalent length comparison.
NOTES:
1. RADIUS ALL CORNERS .005 - .015, UNLESS OTHERWISE SPECIFIED
2. REGRIND NOT ALLOWED
AC
A
B
C
D
WIRSBO COMPANY
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
SCALE
SIZE
CAD FILE:
PART NO.
A
SHEET
OF
REV.
APPROVALS DATE
DRAWN BY
APPROVED BY
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
TOLERANCES ARE:
MATERIAL
ACUDEL 22000
BK937
DO NOT SCALE DRAWING
2
3
456
7
8
A
B
C
D
2
3
4
5
6
7
8
5925 148TH STREET WEST
APPLE VALLEY, MN 55124
PHONE (952) 891 - 2000
FAX (952) 891 - 1246
P4755050
AC
P4755050
ALP 07/21/05
REVISIONS
LETTER
ECO #DATE
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
UPONOR WIRSBO. ANY REPRODUCTION
IN PART OR WHOLE WITHOUT THE
WRITTEN PERMISSION OF UPONOR
WIRSBO IS PROHIBITED.
ANGLES
±
1
∞
.X
±.06
.XX
±.01
.XXX
±.005
SURFACE FINISH UNLESS
OTHERWISE SPECIFIED:
125
250
250
MACH./ MOLDED
OTHER
DRILLED
SSC EP TEE,
1/2" PEX x 1/2" PEX x 1/2" PEX
-
AA NO PRINT
AB APV20650 08/10/05
AC APV20718 09/06/06
LDH 09/11/06
2x R.050
3x P1110502-AA
SECTION A-A
3x .04
2.3 REF
ÿ .485
±.010
BACK SIDE MARKINGS
DETAIL
"Supplier ID"
"Country
of Origin"
"Date Code"
A - Flow
path
B - Internal
diameter
ASTM F1807/F2159
insert tting
ProPEX ASTM F1960
and CAN/CSA B137.5
expansion tting
BB