User manual
Table Of Contents
- About This Manual
- 1 VLAN Configuration
- VLAN Overview
- Configuring VLAN
- Creating VLAN
- Creating a VLAN in VLAN Database
- Setting VLAN Name
- Setting VLAN Link Type on Ethernet Interface
- Adding VLAN Member Port
- Adding Ports to a VLAN in Batches
- Setting the Native VLAN for a Trunk or Hybrid Port
- Setting VLAN Filtering on a Port
- Setting Frame Filtering Type of a Port
- Creating VLAN Layer 3 Interface
- VLAN Configuration Example
- Configuring PVLAN
- Configuring QinQ
- Configuring Subnet VLAN
- Configuring Protocol VLAN
- Configuring VLAN Translation
- Configuring SuperVLAN
- VLAN Maintenance and Diagnosis
- 2 SVLAN Configuration
- 3 SVLAN COS Configuration
- 4 ZESR and SVLAN Linkage Networking Configuration
- 5 MAC Address Table Configuration
- Introduction to MAC Address
- Configuring MAC Address Table
- Setting MAC Address Aging Time
- Burning MAC Addresses
- Configuring MAC Address Permanent
- Binding MAC Address to a Port
- Enabling MAC Address Learning
- Limiting MAC Address Count
- Setting MAC Address Learning Protection
- Setting Port Unkown Source MAC Address Filtering
- Setting MAC Address Filtering
- Viewing MAC Address Table
- MAC Address Table Configuration Example
- 6 STP Configuration
- 7 Link Aggregation Configuration
- 8 IGMP Snooping Configuration
- 9 Sflow Configuration
- 10 ZESS Configuration
- 11 Ethernet OAM Configuration
- 12 UDLD Configuration
- 13 LLDP
- 14 L2PT Configuration
- Figures
- Tables
- Glossary
Chapter10ZESSConguration
Parameter
Description
<1-600>
Preforwardvalue,theunitissecond.Whenthedisconnected
portreconnects,waitforpreforwardtimeandopen
automaticallyunlesshasZESRprotocolconguration.The
defaultvalueis10seconds.
<primary-interface-name><s
econdary-interface-name>
TwoportsofZESS.Innormalcases,secondaryportisblock,
whichavoidsformingstorm.
Example1.Createzessnodethatdomainis1,protect-instanceis1,ports
aregei_1/10andgei_1/20.
ZXR10(config)#zessdomain1protect-instance1
primarygei_1/10secondarygei_1/20
2.Thisdeleteszessthatdomainis1.
ZXR10(config)#nozessdomain1
ConfiguringPreupTime
Tocongurepreuptimeofzessnode,usethefollowingcommand.
CommandFunction
ZXR10(config)#zessdomain<1-4>preup<1-600>
Thedefaultpreuptimeis5
seconds.
ParamtersDescription
Parameter
Description
<1-600>
Preupvalue,theunitissecond.AfterZESSdetectsthatlink
recovers,itdoesn’tswitchstatequicklyuntildelayingpreup
time.Thedefaultvalueis5seconds.
ExampleThisexampleshowshowtoconguredomain1preuptimeas10
seconds.
ZXR10(config)#zessdomain1preup10
ConfiguringZESSMode
TocongureZESSmodeasinversionornon-inversionmode,use
thefollowingcommand.
CommandFunction
ZXR10(config)#zessdomain<1-4>mode{revertive|
non_revertive}
ThisconguresZESSmode
asinversionornon-inversion
mode.
ParamtersDescription
CondentialandProprietaryInformationofZTECORPORATION83