User manual
Table Of Contents
- About This Manual
- 1 VLAN Configuration
- VLAN Overview
- Configuring VLAN
- Creating VLAN
- Creating a VLAN in VLAN Database
- Setting VLAN Name
- Setting VLAN Link Type on Ethernet Interface
- Adding VLAN Member Port
- Adding Ports to a VLAN in Batches
- Setting the Native VLAN for a Trunk or Hybrid Port
- Setting VLAN Filtering on a Port
- Setting Frame Filtering Type of a Port
- Creating VLAN Layer 3 Interface
- VLAN Configuration Example
- Configuring PVLAN
- Configuring QinQ
- Configuring Subnet VLAN
- Configuring Protocol VLAN
- Configuring VLAN Translation
- Configuring SuperVLAN
- VLAN Maintenance and Diagnosis
- 2 SVLAN Configuration
- 3 SVLAN COS Configuration
- 4 ZESR and SVLAN Linkage Networking Configuration
- 5 MAC Address Table Configuration
- Introduction to MAC Address
- Configuring MAC Address Table
- Setting MAC Address Aging Time
- Burning MAC Addresses
- Configuring MAC Address Permanent
- Binding MAC Address to a Port
- Enabling MAC Address Learning
- Limiting MAC Address Count
- Setting MAC Address Learning Protection
- Setting Port Unkown Source MAC Address Filtering
- Setting MAC Address Filtering
- Viewing MAC Address Table
- MAC Address Table Configuration Example
- 6 STP Configuration
- 7 Link Aggregation Configuration
- 8 IGMP Snooping Configuration
- 9 Sflow Configuration
- 10 ZESS Configuration
- 11 Ethernet OAM Configuration
- 12 UDLD Configuration
- 13 LLDP
- 14 L2PT Configuration
- Figures
- Tables
- Glossary
ZXR105900/5200SeriesUserManual(EthernetSwitchingVolume)
LBcanbeusedonlywhenMD,MA,MPandRMEPestablishsuc-
cessfullyandglobalenabledisopened.WhenusingLBfunc-
tion,destinationMPparametercanuseestablishedRMEPID,
RMEPMACaddressormiddleMIPMACaddress.
LBfunctionsupportsSGinterface.
2.ToenableLTfunction,usethefollowingcommand.
LTM(LinktraceMessage):ItisoriginatedbyMEP .Itisusedto
tracktheroutefromMIPtoMIPuntilLTMarriveditsdestination
orMEPcan’tbeforwarded.Itisusedinfaultisolationandroute
discovery.LTM,multicastpacket,whosedestinationaddress
isselectedaccordingtoMDlevelofsendingMEP,isforwarded
toappropriateMDlevelMPbybridgenetwork.LTMpacket
passingmiddleandMIPofMDandMAallsendaLTRtosource
MEPtoensurethepacketarriveshere.DestinationMPcould
beMIP .
CommandFunction
ZXR10#cfmltmmd<1-16>ma<1-32>smep-id
<1-8191>{(dmep-id<1-8191>)|(dmep-mac<xxxx
.xxxx.xxxx>)|(dmip-mac<xxxx.xxxx.xxxx>)}[{[ttl
<1-64>],[timeout<5-10>]]}]
ToenableLTfunction,usethe
followingcommand.
i.LTcanbeusedonlywhenMD,MA,MPandRMEPestablish
successfullyandglobalenabledisopened.
ii.WhenusingLTfunction,destinationMPparametercanuse
establishedRMEPID,RMEPMACaddressormiddleMIP
MACaddress.
iii.LTfunctionsupportsmiddleandbothendsconguredSG
ports.
iv.Ttlparametercan’texceed64hops.IfthemiddleMIP
exceeds64hops,evenifarrivesatthedestination,MPwill
considerthatisnotarrived.
3.ToreadonetimeLTRrouteinformation,usethefollowingcom-
mand.
CommandFunction
ZXR10#cfmltr-readtrans-id<1-4294967295>
ThisreadsonetimeLTRroute
information.Ifreadonetime
arrivingacertainMProute,
thisroutemustbediscovered
successfully.
4.TodisplayMDcongurationinformation,usethefollowing
command.
CommandFunction
ZXR10#showmd{all|(session<1-16>)}
ThisdisplaysMDconguration
information.
5.TodisplayMAcongurationinformation,usethefollowingcom-
mand.
100CondentialandProprietaryInformationofZTECORPORATION