User manual
Table Of Contents
- About This Manual
- 1 VLAN Configuration
- VLAN Overview
- Configuring VLAN
- Creating VLAN
- Creating a VLAN in VLAN Database
- Setting VLAN Name
- Setting VLAN Link Type on Ethernet Interface
- Adding VLAN Member Port
- Adding Ports to a VLAN in Batches
- Setting the Native VLAN for a Trunk or Hybrid Port
- Setting VLAN Filtering on a Port
- Setting Frame Filtering Type of a Port
- Creating VLAN Layer 3 Interface
- VLAN Configuration Example
- Configuring PVLAN
- Configuring QinQ
- Configuring Subnet VLAN
- Configuring Protocol VLAN
- Configuring VLAN Translation
- Configuring SuperVLAN
- VLAN Maintenance and Diagnosis
- 2 SVLAN Configuration
- 3 SVLAN COS Configuration
- 4 ZESR and SVLAN Linkage Networking Configuration
- 5 MAC Address Table Configuration
- Introduction to MAC Address
- Configuring MAC Address Table
- Setting MAC Address Aging Time
- Burning MAC Addresses
- Configuring MAC Address Permanent
- Binding MAC Address to a Port
- Enabling MAC Address Learning
- Limiting MAC Address Count
- Setting MAC Address Learning Protection
- Setting Port Unkown Source MAC Address Filtering
- Setting MAC Address Filtering
- Viewing MAC Address Table
- MAC Address Table Configuration Example
- 6 STP Configuration
- 7 Link Aggregation Configuration
- 8 IGMP Snooping Configuration
- 9 Sflow Configuration
- 10 ZESS Configuration
- 11 Ethernet OAM Configuration
- 12 UDLD Configuration
- 13 LLDP
- 14 L2PT Configuration
- Figures
- Tables
- Glossary
Chapter11EthernetOAMConguration
Step
CommandFunction
18
ZXR10(config-md-ma)#assignmip<1-64>interface
<interfacename>
ThisassignsMIPtoport.
theportcanbesamartgroup.
WhenassigningportforMIP ,
theMEPthatlevelishigher
thanorequaltocurrentMIP
levelcan’texistontheportin
thesamevlansamelevel.
19
ZXR10(config-md-ma)#noassignmep<1-8191>Thiscancelstheassignment
ofMEPtoport.
20
ZXR10(config-md-ma)#noassignmip<1-64>Thiscancelstheassignment
ofMIPtoport.
21
ZXR10(config-md-ma)#mep<1-8191>state{enable|dis
able}
ThissetsMEPmanagement
enabled.
22
ZXR10(config-md-ma)#mep<1-8191>alarm-lowest-pri
<1-5>
ThissetsMEPalarmpriority.
Theveprioritiesfromlow
tohighareRDIalarm,MAC
alarm,RMEPCCMfailure
alarm,ERRCCMalarmand
XCONalarm.
23
ZXR10(config-md-ma)#mep<1-8191>priority<0-7>ThissetsMEPpriority.
24
ZXR10(config-md-ma)#mep<1-8191>ccm-send
{enable|disable}
ThissetsCCpacketsending
enabled.
OAMboardneedn’tenabled,
CCwillbesentautomatically
aslongasglobalenabled.
25
ZXR10(config-md-ma)#mep<1-8191>ccm-check{en
able|disable}
ThischecksCCpacket.
CFMFunctionConfiguration
1.ToenableLBfunction,usethefollowingcommand.
LB(LoopBack)meansaMEPsendsadesignatedMPunicast
CFMPDUforfaultafrmationandisolation.AMPresponses
LBMandsendsunicastpackettoLBMinitiatorMEP .
WhenMPloopresponserreceivesaLBM,checkitsvalidity
rst,ifinvalidthendiscard.IfLBMsourceaddressismulti-
castaddress(notaloneMACaddress)ordestinationaddress
andreceivingMPMACaren’tmatching,MPdiscardsthisLBM
packet.Iftestsucceeds,receivingMPsendsaLBRtoMEPthat
lauchesLBMbytakingLBMsourceaddressasdestinationad-
dress.WhenaLBRisreceivedbyMHF ,ignorethisLBRforthe
reasonthatMIPhasn’ttheentitythatreceivingLBR.
CommandFunction
ZXR10#cfmlbmmd<1-16>ma<1-32>smep-id
<1-8191>{(dmep-id<1-8191>)|(dmep-mac<xxxx.x
xxx.xxxx>)|(dmip-mac<xxxx.xxxx.xxxx>)}[{[repeat
<1-200>],[size<1-400>],[timeout<1-10>]}]
ThisenablesLBfunction.
CondentialandProprietaryInformationofZTECORPORATION99