42" Round Iron Fire Pit
Assembly Instructions OUTDOOR GAS FIRE PIT DANG ER CARBON MONOXIDE HAZARD This appliance can produce carbon monoxide which has no odor. Using it in an enclosed space can kill you. Never use this appliance in an enclosed space such as a camper, tent, car or home. INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. WARNING For outdoor use only. Installation and service must be performed by a quali ed installer, service agency, or the gas supplier.
PARTS LIST 4 WARNING 5 ASSEMBLY 9 OPERATION 12 MAINTENANCE & STORAGE 14 TROUBLESHOOTING 15
Parts List 1 2 PARTS NAME Guard Thermocouple Floor Ground Wire Ignition Pin Body Glass Stone Protective Cover ELectronic Igniter Control Knob Regulator Gas Valve Corrugated Pipe Injector 12 16 17 Adjustable foot pads Battery(AAA) Part 4 1 11 18 Cover Lid Part 1 18 3 17 4 16 5 15 14 13 6 7 8 MATERIAL Qty 1 Q235 Part(250mm) 1 1 Part Part(200mm) 1 Part(250mm) 1 Part 1 1 Part 1(4kg) Part 1 Part 1 ABS 1 Part(3m) 1 Part 1 Part 1 Part 1 Q235 Num .
WARNING PLEASE READ THE FOLLOWING SAFETY RULES PRIOR TO OPERATION OF THE HEATER General informa WARNING 5
WARNING PLEASE READ THE FOLLOWING SAFETY RULES PRIOR TO OPERATION OF THE HEATER WARNING 6
WARNING PLEASE READ THE FOLLOWING SAFETY RULES PRIOR TO OPERATION OF THE HEATER WARNING IF APPLICABLE: 7
WARNING PLEASE READ THE FOLLOWING SAFETY RULES PRIOR TO OPERATION OF THE HEATER WARNING e SAVE ALL INSTRUCTIONS FOR FURTHER USE t • THE TANKER IS AWAY FORM THE FIREPLACE 60 INCH (SEE THE PICTURE).
ASSEMBLY INSTRUCTIONS Step 1: (1) Open the ccn and turn it upside down, make sure 4 pieces of it being open up. (2) Lift off the carton carefully and be wary of the accessories inside falling away. (3) Take all the packing materials away except for the paper honeycomb board rounding the top of the firebowl. Step 2: (1) Turn the firebowl heads up on a flat ground. (2) Remove all the paper honeycomb board rounding the top of the firebowl. Step 3: Check each part before using the product.
ASSEMBLY INSTRUCTIONS Step 4: Locate the battery, remove the plastic Cove first. Unscrew the rubber cap of the Electric Ignitor, place a AAA battery into the battery case. Make sure the positive pole ("+") towards the cap. Screw the cap back to the battery case tightly. Step 5: Guard Place the glass stone averagely in the fire bowl on the top of the firebowl. DO NOT PLACE GLASS STONE ON THEGUARD. KEEP GUARD CLEAN. NOTICE: * Do not place lava rocks on the screen.
ASSEMBLY INSTRUCTIONS Step 6: DO NOT COVER THE IGNITION SCREEN when placing the glass stone into the fire bowl. Always keep Ignition SCREEN visible. ** Connect the Pressure-Regulating Valve to the gas tank. Step 7: Step 8: Turn the cylinder valve clockwise to close the gas supply on the gas tank. Screw Regulator Coupling clockwise by hand only. Make sure it is fastened.
OPERATION FOR YOUR SAFETY, READ BEFORE LIGHTING Before performing a leak test, make sure that no sparks can occur and you are in a spacious outdoor area. Connect the propane gas tank to the regulator andturn thevalve on the unit to the “off” position. Brush a soap and water mixture on all connections. Make sure the igniter battery has been installed properly. The igniter will not operate otherwise. Before operating, smell around the appliance and next to the ground for gas odors.
OPERATION FOR YOUR SAFETY, READ BEFORE LIGHTING 1. Turn the cylinder valve on the gas tank counter-clockwise to open the gas supply. 2. Close the storing door on the firebowl for the gas tank. 3. Press and hold the Electric Ignitor. Meanwhile, push and turn the Control Knob counter-clockwise to the "LOW" position. Keep pushing the Control Knob to light the burner. 4. After ignition, release the Electric Ignitor. Continue to push and hold the Control Knob for 45 seconds. 5.
MAINTENANCE & STORAGE To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance activities on a regular basis: Before performing any maintenance always disconnect propanegas tank. Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents. Keep the heating item free and clear from combustible materials. Visually inspect burner for obstructions and keep tank enclosure free and clear from debris.
TROUBLESHOOTING Electrode and burners are wet Igniter battery is dead or backwards Burner will not light using igniter Igniter Pin cracked or brokensparks a crack Residue on Igniter Pin No Gas Flow Burner will not light with match Coupling nut and regulator not fully connected Obstruction of gas flow Wipe dry with cloth. Check that the AA battery is inserted correctly in the igniter or replace the battery. Make sure the plastic wrap on the battery has been removed.
TROUBLESHOOTING Out of Gas Sudden drop in gas flow, or a reduced flame height Irregular flame pattern, flame does not run the full length of the burner Flame blow out Flame seems to lose heat when burning in cold weather - temperature below 50°F Excess flow safety device may have been activated Burner ports are clogged or blocked Check for gas in the LP gas tank Turn control knob to OFF, wait 30 seconds and light outdoor fire table.
TROUBLESHOOTING Problem: Burner JUST LIGHT UP FOR SECOND AND WILL AUTOMATICALLY TURN OFF 1. The thermocouple will be under the Pilot Guard on the top of the unit. Please remove the Pilot guard by unscrewing it from the metal bowl with a screw driver . 2. Once the Pilot Guard has been removed, you will have two components exposed; the copper one is your thermocouple. Please unscrew the nut holding the thermocouple in place. 3.
Questions , problems , missing parts ? Before returning to your retailer , our exceptional customer service is available Email us at service@u-pha.com. We will offer you a best solution as soon as possible https://www.facebook.com/UPHA.
