42'' round Concrete Fire Pit
Questions , problems , missing parts ? Before returning to your retailer , our exceptional customer service is available Email us at service@u-pha.com. We will offer you a best solution as soon as possible https://www.facebook.com/UPHA.
WARNINGS 3 DIAGRAM 4 ASSEMBLY 7 OPERATION 9 MAINTENANCE & STORAGE 10 TROUBLESHOOTING 13
WARNING PLEASE READ THE FOLLOWING SAFETY RULES PRIOR TO OPERATION OF THE HEATER DANGER This appliance can produce carbon monoxide which has no odor. Using it in an enclosed space can hurt you. For outdoor use only. Never use in the unventilated or enclosed areas. If you smell gas: Shut off gas to the appliance. Extinguish any open flame. If odour continues , keep away from the appliance and immediately call your gas supplier or fire areas.
WARNING PLEASE READ THE FOLLOWING SAFETY RULES PRIOR TO OPERATION OF THE HEATER The installation of this unit must adhere to local codes or either the National Fuel Gas Code, ANSI Z223. 1/NFPA54, OR CAN/CGA- B149.1, National Gas and Propane Installation Code. This unit is to be used with propane gas only! (sold separately), is not intended for natural gas. Do not use any solid fuel or charcoal for this unit. Do not use any more than 1/4in depth lava rocks/pumice stones/Lava Glas above the burner holes.
WARNING PLEASE READ THE FOLLOWING SAFETY RULES PRIOR TO OPERATION OF THE HEATER Never place hands or fingers onto upper portion of this unit while in use. Keep all electrical cords and fuel supply hose away from heated surfaces. Combustible material should Not be within 72 inches of the top of the unit, and within 48 inches around the entire unit.
DIAGRAM 1 6 2 7 4 3 5 8 Parts List 1 Glass Stones 4 boxes 2 AA Battery 1 Pc 3 PVC Cover 1 Pc 4 Tank Seat 1 Pc 5 Body 1 Pc 6 Steel Pan 1 Pc 7 Burner 1 Pc 8 Control Knob 1 Pc 9 Electric Ignition 1 Pc 9 4
ASSEMBLY INSTRUCTIONS Step 1: Step 2: (1) Open the carton and turn it upside down, make sure 4 pieces of it being open up. (1) Turn the firebowl heads up on a flat ground. (2) Lift off the carton carefully and be wary of the accessories inside falling away. (2) Remove all the paper honeycomb board rounding the top of the firebowl. (3) Take all the packing materials away except for the paper honeycomb board rounding the top of the firebowl. Step 3: Check each part before using the product.
ASSEMBLY INSTRUCTIONS Step 5: Locate the battery, remove the plastic Cove first. Unscrew the rubber cap of the Electric Ignitor, place a AA battery into the battery case. Make sure the positive pole ("+") towards the cap. Screw the cap back to the battery case tightly. - + Step 6: Place the lava rock averagely in the fire bowl on the top of the firebowl. NOTICE: * Do not place lava rocks on the screen. * To ensure proper function, the Guard on the Burner should never have lava rocks covered over it.
ASSEMBLY INSTRUCTIONS Step 7: DO NOT COVER THE IGNITION SCREEN when placing the lava rock into the fire bowl. Always keep Ignition SCREEN visible. ** Connect the Pressure-Regulating Valve to the gas tank. Step 8: Step 8: Turn the cylinder valve clockwise to close the gas supply on the gas tank. Screw Regulator Coupling clockwise by hand only. Make sure it is fastened.
OPERATION FOR YOUR SAFETY, READ BEFORE LIGHTING Before performing a leak test, make sure that no sparks can occur and you are in a spacious outdoor area. Connect the propane gas tank to the regulator andturn thevalve on the unit to the “off” position. Brush a soap and water mixture on all connections. Make sure the igniter battery has been installed properly. The igniter will not operate otherwise. Before operating, smell around the appliance and next to the ground for gas odors.
OPERATION FOR YOUR SAFETY, READ BEFORE LIGHTING 1. Turn the cylinder valve on the gas tank counter-clockwise to open the gas supply. 2. Close the storing door on the firebowl for the gas tank. 3. Press and hold the Electric Ignitor. Meanwhile, push and turn the Control Knob counter-clockwise to the "LOW" position. Keep pushing the Control Knob to light the burner. 4. After ignition, release the Electric Ignitor. Continue to push and hold the Control Knob for 45 seconds. 5.
MAINTENANCE & STORAGE To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance activities on a regular basis: Before performing any maintenance always disconnect propanegas tank. Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents. Keep the heating item free and clear from combustible materials. Visually inspect burner for obstructions and keep tank enclosure free and clear from debris.
TROUBLESHOOTING Electrode and burners are wet Igniter battery is dead or backwards Burner will not light using igniter Igniter Pin cracked or brokensparks a crack Residue on Igniter Pin No Gas Flow Burner will not light with match Coupling nut and regulator not fully connected Obstruction of gas flow Wipe dry with cloth. Check that the AA battery is inserted correctly in the igniter or replace the battery. Make sure the plastic wrap on the battery has been removed.
TROUBLESHOOTING Out of Gas Sudden drop in gas flow, or a reduced flame height Irregular flame pattern, flame does not run the full length of the burner Flame blow out Flame seems to lose heat when burning in cold weather - temperature below 50°F Excess flow safety device may have been activated Burner ports are clogged or blocked Check for gas in the LP gas tank Turn control knob to OFF, wait 30 seconds and light outdoor fire table.
TROUBLESHOOTING Problem: Burner JUST LIGHT UP FOR SECOND AND WILL AUTOMATICALLY TURN OFF 1. The thermocouple will be under the Pilot Guard on the top of the unit. Please remove the Pilot guard by unscrewing it from the metal bowl with a screw driver . 2. Once the Pilot Guard has been removed, you will have two components exposed; the copper one is your thermocouple. Please unscrew the nut holding the thermocouple in place. 3.
