User manual

33
HEFEKUCHEN/
Sweet
For preparation of sweet yeast
dough
BACKPULVER/
Baking powder
For cakes and biscuits baked with
baking powder
KONFITÜRE/Jam For boiling jams and marmalades
We recommend to buy a second
bread pan (see Technical Service)
which is used only for jam, as the
chemical process during boiling of
jam may affect the coating in that
way, that bread may stick in such
bread pan used for jam.
TEIG/Dough For the preparation of yeast dough -
e.g. dough for pizza, without baking
function
VOLLKORN
SCHNELL/
Wholemeal fast
To prepare wholemeal bread in
short time, due to the short rising
time, the bread remains quite solid
BACKEN/Bake To bake separately prepared
yeast or cake dough (by hand or
in the program-me TEIG). This
programmeis not fitted for special
preparations such as choux pastry
mixture or short-crust pastry).
TEIG SCHNELL/
Dough fast
For the fast preparation of yeast
dough - e. g. dough for pizza,
without baking function
In some programs (BASIS, WEISSBROT, VOLLKORN, HE-
FEKUCHEN und BACKPULVER) several beeps during the
second kneading phase remind you to add more ingredients
such as nuts, seeds, dried fruit etc. Just open the lid, add
the ingredients and close the lid again.
BRÄUNUNG/CRUST
To select the browning degree of the crust: HELL/LIGHT,
MITTEL/MEDIUM or DUNKEL/DARK,
available in all programs except TEIG, KONFITÜRE and
TEIG SCHNELL. The respective setting is indicated by an
arrow in the LCD display.
STUFE/SIZE
This enables the following setting in the various programs:
ST. I / SIZE I = for a small bread weight, approx. 750-
1.000 g
ST II / SIZE II = for a larger bread weigh, approx. 1.000-
1.200 g
Please note, that this option is only available in the pro-
grams BASIS, VOLLKORN, HEFEKUCHEN. The respective
setting is indicated by an arrow in the LCD display. Please
note also our recommendations in the recipes.
PAUSE FUNCTION
The button PAUSE allows to interrupt the program, e. g. for
removal of the kneading blade or to brush the surface etc.
Press the button PAUSE for 1 second in order to interrupt
the programme. The display starts to blink. Now you can
open the breadmaker e.g. to remove the kneading blade.
Then close the lid and press the button PAUSE again for
about 1 second. The display stops blinking and the pro-
gramme is continued.
Attention: Do not interrupt the programme for more than
5 minutes. In case of longer interruptions the rising of the
dough may be disturbed.
As long as the PAUSE function is activated (blinking dis-
play) the START/STOP button is without function and the
programme cannot be stopped completely.
LIGHT
The interior of the breadmaker TOP
EDITION is fitted with a lighting,
which allows to follow the actual
state of the programme without ope-
ning the lid. Just press the button
LICHT and the light turns on. To
switch off the light just press the
button again. After 1 minute the
light is automatically switched off.
EIGENPROGRAMM/USER PROGRAM
In addition to the other numerous programs provided by
the BACKMEISTER
®
you can also program your own USER
PROGRAM. You can change the basic time and program
phase settings as programmed at the factory or leave out
various program phases. This allows you to develop your
own individual program for baking bread or preparing
dough. Below you will find a sample recipe.
First you should become familiar with the following infor-
mation on the basic programming and use of the USER
PROGRAM.
USER PROGRAM
The program features the following options
Browning programmable
Timer programmable
Loaf size I and II not programmable
The default program is the same as for the BASIC program.
Phase Preset Programmable time frame
Total time 3:00 hours
Knead 1 10 minutes 6-14 minutes
Rise 1 20 minutes 20-60 minutes
Knead 2 15 minutes 5-20 minutes
Rise 2 25 minutes 5-120 minutes
Rise 3 45 minutes 0-120 minutes
Bake 45 minutes 0-80 minutes
Keep warm 60 minutes 0-60 minutes
The times can be programmed as shown in the table.
Proceed as follows:
Select the USER PROGRAM with the Menu button.
Select the desired phase with the ABSCHNITT button.
Knead 1 and the programmed time 0:10 for this phase
appear on the display.
The time can be changed by means of the ZEITWAHL but-
ton. Press it repeatedly until the desired time appears on
the display (past OFF, if necessary).
Confirm the change with the ABSCHNITT button. Press
this button again and the next program phase and the pro-
grammed time will appear on the display: Rise 1 = and
0:20.
If the maximum programmable time for the respective pro-
gram phase is exceeded by pressing the ZEITWAHL button,
O will appear on the display if this is possible according
to the above table. This phase is then skipped during the
program.
Every programmed setting must be confirmed by pressing
the ABSCHNITT button, so you can continue programming
the next program phase.
Once you have programmed all phases to suit your pre-
ferences, conclude the programming by pressing the AB-
SCHNITT button and then the START/STOP button. The
programmed time for the user program appears on the dis-
play. The program then starts either immediately or after
the time set via the timer function.