OPERATORS MANUAL SRM60+ MIXER Persons under the age of 18 are not permitted to operate or have accessibility to operate this equipment per U.S. Department of Labor Employment Standards Administration Fact Sheet No. ESA91-3.
Welcome to Univex Thank you for purchasing this Univex Product. Your new SRM60+ mixer has been designed with advanced performance and safety features that make it an excellent addition to your food preparation equipment. Like all Univex mixers, slicers, meat grinders and accessories, this mixer is engineered to provide years of reliable service.
TABLE OF CONTENTS DESCRIPTION PAGE TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 LIST OF ILLUSTRATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 CHOOSING THE RIGHT LOCATION FOR YOUR MIXER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 USER FRIENDLY SWING RING™ SAFETY GUARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OVERALL VIEW OF FOOD MIXER FIGURE 1 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. BOWL BOWL RING BEATER HEAD SHAFT INGREDIENT CHUTE MAGNET SWING RING™ SAFETY GUARD PTO HUB #12 THUMB SCREW LOWER MOUNTING BRACKET UPPER MOUNTING BRACKET 11. 12. 13. 14. 15. 16. 17. 18. 19. 20.
CHOOSING THE RIGHT LOCATION FOR YOUR NEW MIXER When selecting the best location for the mixer, it is helpful to consider the following: • Where is the best location for the operator, both for saving steps and easy viewing? • Is this a good location for product flow as in: • Easy to get ingredients to the mixer? • Destination of the mix after mixing? • Is there existing electrical service at this location? • Does this location provide easy access for cleaning and service? • Check to be sure that your mixer w
To remove the guard, simply reverse the installation procedure. Grip the two halves of the guard and pull it open. Use an upward motion to release each half of the guard from the bracket. To open the guard for access to the bowl, first turn the mixer off by pushing the red “Stop” pushbutton (Figure 1 [15]). Pull open the two halves of the guard and swing one or both guards outward. It is not necessary to remove them.
USING THE BOWL LIFT The mixer will not operate unless the bowl is in the “up” position. Raise the bowl by turning the bowl lift handle (Figure 1 [16]) clockwise. To lower the bowl, turn the bowl lift handle counter-clockwise. If your mixer is equipped with the power lift option (instead of the handle), turn the power bowl lift switch clockwise to raise the bowl and counter-clockwise to lower the bowl. It is necessary to lower the bowl to change the agitator. This also makes the bowl accessible for filling.
USING THE INGREDIENTS CHUTE The ingredients chute provided with your mixer enables you to add ingredients to the bowl while the mixer is running and without opening the Swing Ring™ Safety Guard. The chute may be installed on the front or side of either half of the guard. Once the chute is properly installed, it can remain in place permanently, if desired. INGREDIENTS CHUTE INSTALLATION Slide the bottom of the chute between horizontal safety guard rings and engage the chute onto the safety guard.
USING THE POWER TAKE-OFF (PTO) The Power Take-Off (PTO) hub (Figure 1 [7]) accommodates #12 tapered attachments such as a vegetable slicer and shredder, or a meat and food chopper. The mixers speed control lever also controls the PTO drive speed. Before installing attachments, turn the mixer off and disconnect the electrical power supply. Remove the PTO cap and loosen the thumb screw (Figure 1 [8]) on the PTO hub. Insert the attachment with a slight twist until it is firmly in place.
CLEANING YOUR MIXER Consistent use of the following procedures will ensure that your mixer is in optimum operating condition. • Warning: disconnect the electrical power supply before cleaning. • Wash the body of the mixer, the bowl support, and the beater shaft with warm water and mild soap. • Avoid excess water in the area of the safety switches that protrude from the housing where the Swing Ring™ Safety Guard is mounted. • Do not rinse the mixer with a hose. • Do not use abrasive pads to wash the mixer.
TROUBLE-SHOOTING GUIDE TROUBLE 1. Mixer will not operate 2. Mixer runs but agitator will not turn. 3. Agitator stalls during mixing POSSIBLE CAUSE 1.1 Electrical service down. 1.2 Burned switch contacts. 1.3 Timer not turned on. 1.4 Motor capacitor defective (1PH only) 1.5 Burned out motor. 1.6 Magnetic starter tripped due to overload. 1.7 Safety Ring not mounted and closed. 1.8 Bowl not raised. 2.1 Shifting speed with the mixer not running. 2.2 Broken or slipping belt. 2.
Beaters, Agitators, Bowls, and Accessories Available for the SRM60+ Mixer Figure 3 Part numbers (size in quarts) A. Batter Beater 1061083 (60) H. Bowl Dolly Optional 1061971 (60) 1030971 (30 for 60) Optional 1061096 (30 for 60) B. Wire Whip 1061095 (60) I. 30 for 60 Dolly Adapter Optional 1030972 (30) Optional 1061182 (30 for 60) C. Dough Hook 1061089 (60) J. Splash/Extension Ring Optional 1061298 (60) 1061299 (30 for 60) Optional 1061090 (30 for 60) D. Pastry Knife K.
Table of Mixing capacity and Recommended Agitators Figure 4 MODEL SRM 60+ Bowl capacity Attachment Hub Size Motor 72 qt. #12 3 Hp 68.1 L 40 lb. 12 qt. 18 qt. (oil) 18.2 kg. 11.4 L. 17 L.
WIRING DIAGRAM (208-240V, 60HZ, 1PH) (220-240V, 50HZ, 1PH) FIGURE 5A IMPORTANT: Before making any electrical connections, check the specifications on the data plate, (located on the rear access panel Figure 1 [17]), to make sure that they agree with those of your electrical service. WARNING: Whenever maintenance is being performed, or whenever the top cover or rear access panel have been removed, DISCONNECT THE ELECTRICAL POWER SUPPLY and place a tag on it indicating that the mixer is being worked on.
WIRING DIAGRAM (208-240V, 60HZ, 3PH) (220V, 50HZ, 3PH) (200V, 50/60HZ, 3PH) FIGURE 5B IMPORTANT: Before making any electrical connections, check the specifications on the data plate, (located on the rear access panel Figure 1 [17]), to make sure that they agree with those of your electrical service.
WIRING DIAGRAM (460V, 60HZ, 3PH) (380V, 50HZ, 3PH) FIGURE 5C IMPORTANT: Before making any electrical connections, check the specifications on the data plate, (located on the rear access panel Figure 1 [17]), to make sure that they agree with those of your electrical service. WARNING: Whenever maintenance is being performed, or whenever the top cover or rear access panel have been removed, DISCONNECT THE ELECTRICAL POWER SUPPLY and place a tag on it indicating that the mixer is being worked on.
Warranty The Univex SRM60+ mixer carries a two-Year, on-site, parts and labor warranty against any defects in materials or workmanship. The two-year period begins on the date of purchase by the end user and remains in full effect provided the unit is used properly in accordance with our instructions. Any Work to be performed under this warranty must be performed between the hours of 8:00 a.m. and 5:00 p.m. local time, Monday through Friday. Univex will not cover overtime charges of any kind.
