PowerLite Home Cinema 700 Home Theater Projector ® User’s Guide
Important Safety Information WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.
Trademarks Epson and Instant Off are registered trademarks, and Epson Exceed Your Vision is a registered logomark of Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks, SizeWise is a trademark, and Extra Care is a service mark of Epson America, Inc. Pixelworks, DNX, and the DNX logo are trademarks of Pixelworks, Inc. HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.
C Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . 10 Projector Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Projector Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . 12 Remote Control Map. . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Projector Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Displaying and Adjusting the Image . . . . . . . . 39 Selecting an Image Source . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Adjusting the Position of the Image . . . . . . . . . . . . . . . . 41 Adjusting the Image Shape. . . . . . . . . . . . . . . . . . . . . . . 41 Focusing and Zooming the Image . . . . . . . . . . . . . . . . . 42 Selecting the Color Mode . . . . . . . . . . . . . . . . . . . . . . .
5 Maintaining the Projector . . . . . . . . . . . . . . . . . . . 71 Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Cleaning the Projector Case . . . . . . . . . . . . . . . . . . . . . . . . . 72 Cleaning the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Replacing the Air Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
W - Welcome The PowerLite ® Home Cinema 700 lets you enjoy High-Definition, theater-quality images in the relaxing environment of your own home. You can connect it to a wide range of video sources and computers, so you can enjoy perfectly adjusted images from all your movies and games.
Using Your Documentation This book contains all the information you need to set up and use your projector. Please follow these guidelines as you read through it: ■ Warnings must be followed carefully to avoid bodily injury. ■ Cautions must be observed to avoid damage to your equipment. ■ Notes contain important information about your projector. ■ Tips contain additional projection hints.
Projector Parts Kensington lock port Control panel Lens cover Focus and Zoom rings Infrared receiver Adjustable foot SD card slot USB (TypeA) port Ventilation slots USB (TypeB) port Video port Adjustable foot and release lever S-Video port Computer (Component Video) port HDMI port Audio ports AC power inlet Infrared receiver Lamp cover Welcome 11
Mounting bracket holes (M4×9 screws required) Air filter Security cable slot Projector Control Panel Source Search button (searches for connected video sources) Menu button (displays projector menus) Esc button (exits menu items) Power light and button Lamp and Temperature warning lights 12 Welcome Enter button (selects menu items) Help button Volume down button Keystone buttons (correct screen shape) Volume up button
Remote Control Map Power button Search and Source buttons (select image source) A/V Mute button (turns off image) Auto button (resets tracking, sync, and position) Aspect button (changes screen size) Page Up/Down buttons (control PowerPoint® slides; USB cable required) Freeze button (stops image) Color Mode button (changes display mode) Num button (activates number buttons) Help button (displays help menus) E-Zoom +/– buttons (zoom into image) Volume buttons (adjusts volume) Menu button (accesses menu
Projector Dimensions Use the dimensions below to guide you in placing or installing the projector. Center of lens 3.73 in. (94.7 mm) 0.26 in. (6.7 mm) 3.21 in. (81.5 mm) 1.95 in. (49.6 mm); center of lens to mounting bracket holes 12.87 in. (327 mm) 3.64 in. (92.5 mm) 3.62 in. (92 mm) 9.65 in. (245 mm) 0.47 in. (12 mm) 4.53 in. (115 mm) 14 Welcome 5 in. (127 mm) 2.66 in. (67.
Registration and Warranty Your projector comes with a basic warranty that lets you project with confidence. For details, see the warranty brochure included with your projector. In addition, Epson offers free Extra Care Home Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States or Canada, usually via overnight delivery. See the brochure included with your projector for details.
Product Part number Distribution amplifier ELPDA01 Image presentation camera (ELPDC05) DC-10s document camera V12H162020 ELPDC10S Soft carrying case (projector only) Soft shoulder case for projector and notebook Wheeled soft carrying case Molded hard-shell wheeled carrying case Swiss Gear® backpack V12H00160 ELPKS61 ELPKS62 ELPKS58 ELPKS63 You can purchase screens or other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766).
1 1 Setting Up the Projector T his chapter tells you how to unpack the projector and connect it to video equipment, such as a VCR, DVD player, or video camera, and/or to a notebook or desktop computer. You can also connect the projector to a USB storage device or digital camera, or project from an inserted SD card.
Unpacking the Projector After unpacking the projector, make sure you have all these parts: PDF manual and registration CD-ROM Component-to-VGA video adapter Projector Power cord Remote control and batteries Save all packaging in case you need to ship the projector. Always use the original packaging (or the equivalent) when you need to send the projector to another location; see page 79 for instructions.
Positioning the Projector You can place the projector in a variety of viewing setups. When projecting from the front, place the projector directly in front of the center of the screen, facing the screen squarely. The center of the lens should be about level with the bottom of the screen. note After positioning the projector, you may want to connect a Kensington MicroSaver® anti-theft device to the lock port on the projector. You can purchase this from Epson; see page 15.
You can also install the projector in two other viewing setups: rear projection onto a semi-transparent screen, or rear/ceiling projection. If you project from overhead or the rear of the screen, you’ll need to select the appropriate Projection setting in the projector’s Extended menu to orient the image correctly (see page 62). Keep these considerations in mind as you position the projector: ■ Place the projector on a sturdy, level surface.
16:10 image Diagonal screen size Projection distance (A) Wide to Tele 50 inches (127 cm) 62 to 75 inches (158 to 191 cm) 60 inches (152 cm) 75 to 90 inches (191 to 230 cm) 80 inches (203 cm) 101 to 121 inches (255 to 307 cm) 100 inches (254 cm) 126 to 152 inches (320 to 385 cm) 150 inches (381 cm) 190 to 228 inches (482 to 579 cm) 200 inches (508 cm) 253 to 305 inches (644 to 774 cm) 250 inches (635 cm) 317 to 381 inches (806 to 968 cm) 4:3 image Screen size Projection distance (A) Wide to
4:3 image Screen size Projection distance (A) Wide to Tele 200 inches (508 cm) 287 to 345 inches (729 to 876 cm) 235 inches (597 cm) 338 to 406 inches (857 to 1030 cm) 16:9 image 22 Setting Up the Projector Screen size Projection distance (A) Wide to Tele Offset (B) 27 inches (69 cm) 34 to 41 inches (86 to 104 cm) 0.7 inch (2 cm) 30 inches (76 cm) 38 to 46 inches (96 to 116 cm) 0.8 inch (2 cm) 40 inches (102 cm) 51 to 62 inches (130 to 156 cm) 1.
Connecting to Video Equipment You can connect several video sources to the projector at the same time. Before starting, look at your video equipment to determine its available video output connections: ■ If your video player has an HDMI connector, see “Connecting an HDMI Video Source” on page 24. ■ If your video player has a component video port (three connectors labeled either Y/Cb/Cr or Y/Pb/Pr), see “Connecting a Component Video Source” on page 25.
Connecting an HDMI Video Source note If an HDMI cable was not provided with your video device, you can purchase one from an electronics dealer. For the best image and sound quality, connect your video equipment to the HDMI (High-Definition Multimedia Interface) port, if possible. Connect an HDMI cable to the HDMI connector on your player and the HDMI port on the projector.
Connecting a Component Video Source If your video equipment has component video connectors (three connectors labeled either Y/Cb/Cr or Y/Pb/Pr), you can use the component-to-VGA video adapter that came with your projector and a component video cable, or you can purchase a component-to-VGA video cable from Epson (see page 15) or an electronics dealer. 1. Connect one end of your component video cable to the Y/Cb/Cr (or Y/Pb/Pr) connectors on your player. 2.
Connecting a Composite Video Source note If the video cable was not provided with your video device, you can purchase one from an electronics dealer. 1. If your video cable has an RCA connector, connect it to the yellow video output connector on your player and the yellow Video port on the projector. Video port 2. If you want to play sound through the projector, see page 32 for instructions on connecting an audio cable.
Connecting an S-Video Source 1. Connect the S-Video cable to the S-Video connector on your player and the S-Video port on the projector. S-Video port note If the S-Video cable was not provided with your video device, you can purchase one from Epson; see page 15. 2. If you want to play sound through the projector, see page 32 for instructions on connecting an audio cable.
Connecting an RGB Video Source note You can purchase a VGA computer cable from an electronics dealer. You can connect to an RGB video source using a VGA computer cable. 1. Connect the cable to the RGB video port on your player and the Computer (Component Video) port on the projector. Computer (Component Video) port 2. You may need to change the Input Signal setting in the projector’s Signal menu to RGB (see page 60). 3.
Connecting to a Computer You can connect the projector to a Windows computer using the projector’s TypeB USB port. This lets you carry a lightweight cable with you when you transport the projector. You can also connect the projector to any computer that has a standard video output (monitor) port, including desktop models, PC notebook computers, Macintosh PowerBook® and iBook® computers, and hand-held devices. See page 31 for instructions on connecting using a VGA computer cable.
4. Connect the square end of a USB cable to the projector’s TypeB (square) USB port. USB TypeB port 5. Connect the flat end of the cable to any available USB port on your notebook or desktop computer. Messages appear on your computer screen as the projector is recognized and the software is installed automatically. 6. Follow the instructions on the screen to install the Epson USB Display software. If you see a “Digital Signature Warning,” select Continue or Continue Anyway.
Connecting to the VGA Computer Port You can connect to the projector using a VGA computer cable. 1. Connect one end of a VGA computer cable to the projector’s Computer (Component Video) port and the other end to your computer’s monitor port. note You can purchase a VGA computer cable from an electronics dealer. Computer (Component Video) port caution Don’t try to force a connector to fit a port with a different shape or number of pins. You may damage the port or connector. 2.
Playing Sound Through the Projector You can play sound through the projector’s speaker system. 1. Locate the appropriate cable and connect it to the Audio jacks on the projector. Audio jacks 2. Connect the other end of the cable to the audio output connector(s) on your computer or video equipment. Connecting a Digital Camera or Other USB Device note Use a cable less than 10 feet (3 meters) long and connect the camera or other device directly to the projector.
2. Connect the USB drive or the flat end of the USB cable to the USB TypeA port on the projector, as shown. Indicator light 3. Connect the other end of the cable to your camera or other device, if necessary. The indicator light turns orange and then green when a USB device is connected. 4. If you are not connected to another image source, the Slideshow program appears. If you are connected to another image source, press the Slideshow button on the remote control to start the Slideshow program.
Inserting an SD Card You can use an SD or SDHC™ (SD High Capacity) card to store images or PowerPoint presentation slides converted to .JPG files. This lets you project your files without connecting to a laptop or PC. To place your files on the card, copy them from your computer to the card using a card reader. 1. Follow the instructions beginning on page 35 to turn on the projector. 2.
To remove the card, gently press the inserted SD card. The card pops out so you can remove it. Turning the Projector On and Off Turn on any connected computer or video equipment before starting the projector so it can automatically detect and display the image source. If you turn on the projector first, or have multiple pieces of connected equipment, you may have to select the image source manually (see page 40). Follow these steps to turn on the projector: 1. Open the A/V Mute slide (lens cover).
2. Plug one end of the power cord into the projector, and the other end into an electrical outlet. The Ppower light turns orange. Power light 3. Press the Ppower button on the remote control or on the projector.
The projector beeps once and the Ppower light flashes green as the projector warms up, then an image begins to appear. When the Ppower light stops flashing and remains green, the projector is ready for use. 4. If you are prompted to enter a password, see page 65. warning Never look into the lens when the lamp is on. This can damage your eyes, and is especially dangerous for children. Using the Direct Power On Function The Direct Power On function enables faster setup.
Shutting Down the Projector note Lamp life results will vary depending upon mode selected, environmental conditions, and usage. This projector incorporates Instant Off technology. To turn it off, you can press its Ppower button as described below, unplug it, or turn off a power switch that supplies power to the projector. You don’t have to wait for the projector to cool down first. Turn off this product when not in use to prolong the life of the projector. 1.
2 2 Displaying and Adjusting the Image Follow the guidelines in this chapter for: ■ Selecting an image source ■ Adjusting the image 39
Selecting an Image Source You may need to select the image source if you have multiple image sources connected to the projector (such as a computer or DVD player). Selecting the image source lets you switch between images input from different pieces of connected equipment. If you don’t see the image you want, press the Search button or one of the Source buttons on the remote control, or press the Source Search button on the projector.
Adjusting the Position of the Image If the image is too low on the screen, you can use the front adjustable foot to raise it. 1. Press the foot release lever up and lift the front of the projector. 2. Once the image is positioned where you want it, release the lever to lock the foot in position. 3. If the image is tilted or you need to fine-tune the height of the image, you can turn the projector’s adjustable rear feet.
The projector’s Auto Keystone function detects and corrects vertical keystone distortion up to 11°. It takes about one second after the projector starts for the image to be corrected. If your image is still distorted, do one of the following: ■ Press the appropriate keystone correction button on the projector’s control panel until the shape is evenly rectangular. Keystone correction buttons ■ Select the Keystone setting in the projector’s Settings menu (see page 61).
You can also use the E-Zoom buttons on the remote control to zoom in on a portion of the image. See page 47 for instructions. Selecting the Color Mode The Color Mode adjusts the brightness, contrast, and color for various common viewing environments. Use this setting to quickly obtain a good picture. Press the Color Mode button on the remote control until the option you want is projected in the upper right corner.
Resizing Video Images note You cannot change the aspect ratio when displaying from a computer using the USB TypeB port or from a USB device or SD card using the Slideshow source. You can resize your images by changing the aspect (width to height) ratio (depending on your input signal). Press the Aspect button on the remote control repeatedly to cycle through the available options. Aspect button You can also select the Aspect setting from the projector’s Signal menu. See page 59 for instructions.
3 3 Presenting With the Remote Control The projector includes a number of tools to enhance your presentation. All of them can be accessed using the remote control, which lets you operate the projector from anywhere in the room—up to 19.7 feet (6 meters) away.
Using the Remote Control note If a button is pressed for longer than 30 seconds, the remote control stops operating to conserve battery power. When you release the button, normal operation resumes. Using the remote control under bright fluorescent lamps or in direct sunlight may affect projector response. Make sure batteries are installed as described on page 78. Follow these tips for using the remote control: ■ Point the remote control at the front or back of the projector, or at the screen.
You can also set the Lens Cover Timer setting to automatically turn off the projector after 30 minutes to protect the projector if the A/V Mute slide is closed for a long time. See page 62 for instructions. Stopping Action Press the Freeze button on the remote control to stop the action in your video or computer image. The image freezes but the sound continues. note To restart the action, press the Freeze button again. The Freeze function pauses the image, not the sound.
Controlling the Volume To change the volume, press the or button on the remote control or on the projector’s control panel. note To temporarily shut off the sound and picture, press the A/V Mute button or close the A/V Mute slide. Volume buttons You can also adjust the volume using the projector’s menu system. See page 61.
To control presentation slides using the remote control’s Page Up or Page Down buttons, select Page Up/Down as the USB Type B setting on the Extended menu (see page 62). Then you can control your presentation using those buttons. Page up or down to change slides in PowerPoint Right-click Left-click If you want to use the remote control like a wireless mouse, select Wireless Mouse as the USB Type B setting on the Extended menu (see page 62).
Presenting a Slideshow You can use your projector’s Slideshow feature whenever you insert an SD card or connect a USB device that contains .JPG image files. This lets you quickly and easily display individual images, or start a slideshow of all the images in a folder. You can control your slideshow using the projector remote control. note You can project .JPG files in resolutions up to 8176 × 6144, with pixel counts incrementing in multiples of 8. If the .
If you are not connected to another image source, the Slideshow program appears automatically. 3. If you inserted an SD card and connected a USB device at the same time, you see a screen like this: Press the arrow buttons on the remote control to highlight the device you want to present from, then press the Enter button. 4. If you need to select a subfolder on your device, press the arrow buttons to highlight the folder and press Enter. 5.
note To display a slideshow from a folder that is not open, highlight the folder and press the Esc button on the remote control. Then select Slideshow from the menu that appears and press Enter. To begin a slideshow from a particular image, use the arrow buttons to highlight that image, press Enter, then press Enter again. 6. To display a slideshow of all the images in the current folder, use the arrow buttons to highlight Slideshow on the bottom of the Slideshow screen and press Enter.
2. Highlight the options you want to use, and press Enter. Option Available settings Display order Name order displays files in name order Date order displays files in date order Sort order In Ascending sorts the files first to last In Descending sorts the files last to first Continuous play On displays a slideshow continuously Off displays a slideshow one time through Screen switching time No does not switch file display automatically 1Sec. to 60Sec.
Presenting With the Remote Control
4 4 Fine-Tuning the Projector You can use the projector’s on-screen menus to adjust the image, sound, and other features.
Using the Menu System You can use the remote control or the projector’s control panel to access the menus and change settings. Follow these steps: 1. To display the menu screen, press the Menu button on the remote control or on the projector. You see a menu screen similar to the one below: Options Menu list The menus are listed on the left and the options available for the highlighted menu are shown on the right. 2.
Restoring the Default Settings You can use the Reset option on any menu to restore the factory-default settings for the settings in that menu. To restore all the projector settings to their factory-default values, select the Reset menu, highlight Reset All, press Enter, and select Yes to confirm. note When you select Reset All in the Reset menu, it does not reset the Input Signal, User’s Logo, Language, or Lamp Hours settings.
note 2. Adjust the desired options as needed: The available settings vary depending on the input source selected. The Brightness setting changes the opacity of the projector’s LCD panels. You can also change the lamp’s brightness. Select Brightness Control in the Settings menu, then choose High or Low (the default setting is High). ■ Color Mode Lets you quickly adjust the color and brightness for various environments. You can save a different setting for each source.
Adjusting Signal Settings Although the projector normally detects and optimizes the input signal automatically, you can use the Signal menu to make manual adjustments. In addition to changing the position of the projected image, you can correct tracking and sync for computer images, or change the aspect ratio. 1. Press the Menu button and select the Signal menu. You see a screen similar to one of those below. (The settings will be different depending on the source you are projecting from.
■ note You can also use the remote control’s Auto button to automatically reset the projector’s Tracking, Sync, and Position settings. See page 89 for details. Tracking Adjust this value to eliminate vertical stripes in computer images. ■ Sync Adjust this value if computer images appear blurry or flicker. ■ Position If the image is slightly cut off on one or more sides, it may not be centered exactly. Select this setting and use the arrow buttons to center it.
Customizing Projector Features You can use the Settings menu to lock the buttons on the projector, adjust audio volume, and customize several other features. ■ Keystone Adjusts the shape of the image if the projector has been tilted upward or downward. If you notice that lines or edge look jagged after adjustment, decrease the Sharpness setting (see page 57). ■ Auto Keystone Automatically compensates for keystone distortion when the projector is tilted upward or downward.
Customizing Power and Operation You can use the Extended menu to customize the way the projector displays images, enable Direct Power On, turn sleep mode on or off, and customize other projector operations. ■ Display Messages: Lets you turn screen messages on or off. Display Background: Sets the screen background to Black, Blue, or Logo when no image signal is available. Startup Screen: Enables or disables display of the startup (User’s Logo) screen when the projector is turned on.
Sleep Mode: Enable if you want the projector to turn off automatically if it is idle and no signal is received for 1 to 30 minutes (you can adjust the amount of time using the next setting). Sleep Mode Timer: When Sleep Mode is on, you can set the period of time before the projector turns off automatically, from 1 to 30 minutes. Lens Cover Timer: Enabled by default to turn the projector’s power off automatically when the A/V Mute slide is closed for more than 30 minutes.
caution If you lose the remote control, you will not be able to enter the password. Keep the remote control in a safe place at all times. Also, it’s a good idea to write down your password. ■ Disable the projector’s buttons; this is useful, for example, in a classroom when you want to ensure that no one touches the projector’s buttons while you’re using the remote control. See page 68. ■ Secure the projector to prevent theft using a cable locking system. See page 69.
5. Hold down the Num button and use the numeric keypad to enter a four digit password. Hold down 6. When you see a confirmation message, reenter the password. 7. Press the Menu button, then press Enter to exit the screen. 8. Turn off and unplug the projector. Starting the Projector With a Password When the password function is enabled, you see this screen when you plug in and turn on the projector: note If you leave the projector plugged in, the Password screen will not appear.
If projection does not begin, check the following: ■ If the password is not correct, you see a message prompting you to re-enter the password. If you enter an incorrect password three times in succession, you see an error code with the message The projector’s operation will be locked and the projector switches to standby mode. Write down the error code, then disconnect the projector’s power cord from the electrical outlet, reconnect it, and turn the projector back on.
Capturing the Image Start by displaying the image you want to use from either a computer or video source, such as a DVD player or digital camera. Then follow these steps to capture the image and transfer it to the projector: 1. Press the Menu button on the remote control, highlight the Extended menu, and press Enter. note When you choose an image for the user’s logo, it erases any previously used image. You can save an image up to 300 × 400 pixels in size.
Choosing When to Display the Image After your image is saved, you can set it to display as the startup screen, the screen you see when there’s no signal, or the screen you see when you press the A/V Mute button (see page 46). 1. Press the Menu button, highlight the Extended menu, and press Enter. 2. Select Display and press Enter. 3. Choose from these display options: note You can lock these settings to prevent them from being changed without a password (see page 64).
5. Press the Menu button to exit. To disable the Control Panel Lock function, select Off in the Control Panel Lock menu. Or press and hold the Enter button on the projector’s control panel for seven seconds. A message is displayed and the lock is released. Using Security Locking The projector includes two security locking points to prevent its theft when installed or used in public locations: ■ Security cable attachment.
Fine-Tuning the Projector
5 5 Maintaining the Projector Y our projector needs little maintenance. All you have to do on a regular basis is clean the lens, and check that the air filter and vents are clean. A clogged air filter or vent can block ventilation needed to cool the projector. warning Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp cover. Dangerous electrical voltages in the projector can injure you severely.
Cleaning the Lens Clean the lens whenever you notice dirt or dust on the surface. caution To remove dirt or smears on the lens, use a commercially available cloth for cleaning glasses. Do not rub the lens with harsh materials or subject the lens to shocks, or you may damage it. Cleaning the Projector Case Do not use wax, alcohol, benzene, paint thinner, or other chemical detergents. These can damage the case. Before cleaning, turn off the projector and unplug the power cord.
You can remove the air filter to clean both sides If the filter is too dirty or broken, replace the filter as described below. Replacing the Air Filter You need to replace the air filter if: ■ You cannot remove the dust from it ■ The air filter is damaged or torn ■ You repeatedly see a projected message telling you to clean or replace it Contact your dealer or call Epson at 800-GO-EPSON (800-463-7766) to obtain a new air filter. Request part number V13H134A13. 1.
Replacing the Lamp note Turn off this product when not in use to prolong the life of the projector. The life span of the projection lamp is about 3000 hours if Brightness Control in the Settings menu is set to High (default), and 4000 hours if Brightness Control is set to Low. See page 77 to check the lamp usage. It is time to replace the lamp when: warning Let the lamp cool fully before replacing it. ■ The projected image gets darker or starts to deteriorate.
3. Loosen the lamp cover screw (you cannot remove it). Then slide the lamp cover off. 4. Loosen the two screws holding the lamp in place (you can’t remove them). Loosen, but don’t remove these screws note 5. Hold the lamp as shown and pull it straight out. The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.
6. Gently insert the new lamp. (If it doesn’t fit easily, make sure it is facing the right way.) Then tighten its screws. 7. Replace the lamp cover, then tighten its screw. note Tighten the lamp cover securely so you do not receive a lamp cover error when you turn the projector back on. 8. Reset the lamp timer as described in the next section. Resetting the Lamp Timer After you replace the lamp, you need to reset the lamp timer using the projector’s menu system.
2. Select the Reset menu and press Enter. You see this screen: 3. Select Reset Lamp Hours and press Enter. 4. When you see the prompt, select Yes and press Enter. 5. When you’re finished, press Menu to exit. Checking Lamp Usage To check the number of hours the lamp has been used, press the Menu button and highlight the Info menu. You see a screen like this: note The information displayed depends on the input signal currently selected.
Replacing the Remote Control Batteries caution Replace the batteries in the remote control as described below: When replacing batteries, take the following precautions: 1. Turn the remote control over. 2. Press in on the catch on the battery cover as you lift the cover off. ■ Replace the batteries as soon as they run out. If the batteries leak, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash immediately. ■ Do not expose batteries to heat or flame.
Transporting the Projector The projector contains many glass and precision parts. When hand-carrying the projector, use an optional carrying case. note Follow these guidelines to prevent damage when transporting it: ■ When shipping the projector for repairs, use the original packaging material if possible. If you do not have the original packaging, use equivalent materials, placing plenty of cushioning around the projector.
Maintaining the Projector
6 6 Solving Problems This chapter helps you solve problems with your projector and tells you how to contact technical support for problems you can’t solve yourself.
Using On-Screen Help If the image doesn’t look right or your audio isn’t working, you can get help by pressing the ? Help button on the projector or the remote control. 1. Press the ? Help button on the remote control or on the projector. You see the Help menu: 2. Use the arrow buttons on the remote control or the projector to highlight menu items. 3. Press the Enter button on the remote control or the projector to select the menu item and read the solutions. 4.
Checking Projector Status If your projector isn’t working correctly, first turn it off and unplug it. Then plug the power cord back in and turn on the projector. If this doesn’t solve the problem, check the lights on top of the projector. What To Do When the Lights Come On or Flash The lights on top of the projector indicate the projector’s status.
Error light(s) status Error light(s) status Description P Green or orange It’s time to replace the lamp. See page 74 for instructions. If you continue to use the lamp after the replacement warning, there is an increased possibility that the lamp may break. Flashing orange Off P Red Off Flashing orange P Red Off Red Rapid cooling is in progress. Although this is not an abnormal condition, projection will stop automatically if the temperature rises higher.
Solving Projector Operation Problems The power doesn’t turn on. ■ If the projector doesn’t turn on when you press the Ppower button, make sure the power cord is connected to the projector and plugged into a working electrical outlet. ■ The power cord may be defective. Disconnect the cord from the outlet and contact Epson as described on page 92. ■ If you’re using the Direct Power On function and you immediately plug the power cord back in after unplugging it, the power may not turn back on.
■ The attached computer may be in sleep mode or displaying a black screen saver. Try pressing a key on the computer. ■ If you are projecting from a DVD player or other video source, make sure you turn it on and press its Play button. ■ If you are projecting from a composite or S-Video video source, make sure the Video Signal setting is correct (see page 59). ■ You can also try resetting all of the menu settings (see page 57).
If you’re using Mac OS X: 1. Open System Preferences. 2. Click Display or Displays. 3. Select VGA Display or Color LCD. 4. Click Arrangement or Arrange. 5. Select Mirror Displays. The message Not Supported is displayed. ■ Make sure the correct input signal is selected in the Signal menu (see page 59). ■ Make sure your computer’s resolution and frequency or refresh rate is supported by the projector (see page 98). If necessary, change your computer’s settings.
■ If you’re projecting an image from a computer with dual display activated, turn dual display off. The image isn’t square, but keystone-shaped. If the image isn’t evenly rectangular, adjust its shape as described on page 41. The image contains static or noise. ■ If you’re using a computer cable longer than 6 feet (1.8 meters), or an extension cable, the image quality may be reduced. ■ Keep your computer and video cables away from the power cord as much as possible to prevent interference.
■ If the projector is angled sharply toward the screen, it may not be possible to focus the entire image. Move the projector to position it more directly in front of the screen. ■ Lower the projection angle to reduce the amount of keystone correction required. ■ Make sure the projector is within the proper range (projection distance) from the screen (see page 19). ■ Make sure the lens is not fogged by condensation.
3. Adjust the Sync setting to increase the image sharpness. The image is too light or dark, or colors are incorrect. note Because of the different technologies used, your projected image may not exactly match the colors on your notebook or computer monitor. ■ Press the Color Mode button or select a different Color Mode option in the Image menu. See page 43 for details on the available options. ■ If you’re displaying video, adjust the Color Adjustment and Color Mode settings on the Image menu.
■ If your presentation includes computer audio, make sure the volume control on your computer is not turned all the way down or muted. In Windows, you may be able to check this by clicking the volume control in your Windows system tray (lower right corner of the screen). On a Mac, you may be able to adjust the volume from your menu bar (top right corner of the screen) or via the volume control function keys.
Where To Get Help Epson provides these technical support services: Internet Support Visit Epson’s support website for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions. Speak to a Support Representative To use the Epson PrivateLine Support service, call (800) 637-7661 and enter the PIN on the included Epson PrivateLine Support card. This is the fastest way of speaking to a live representative, and it’s free.
Before you call for support, please have the following information ready: ■ Product name (PowerLite Home Cinema 700) ■ Product serial number (located on the projector) ■ Proof of purchase (such as a store receipt) and date of purchase ■ Computer or video configuration ■ Description of the problem Purchase Supplies and Accessories You can purchase screens and other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766).
Solving Problems
A A Technical Specifications General Type of display Epson poly-silicon TFT active matrix Resolution (native format) 1280 × 800 pixels (WXGA) Color reproduction 16.
Noise level 28 dB in Low Brightness mode 35 dB in High Brightness mode Keystone correction Manual: ±30° vertical Auto Keystone: 0 to 11° vertical Projection Lamp note Lamp life results will vary depending upon mode selected, environmental conditions, and usage. Turn off this product when not in use to prolong the life of the projector. Type UHE (Ultra High Efficiency) Power consumption 170 W Lamp life Approx. 3000 hours (High Brightness mode) Approx.
Environmental Temperature Humidity (non-condensing) Operating altitude Operating: 41 to 95 °F (5 to 35 °C) Storage: 14 to 140 °F (–10 to 60 °C) Operating: 20 to 80% RH 0 to 7500 ft (0 to 2286 m); over 4921 ft (1500 m), enable High Altitude mode in the Extended menu (see page 62) Safety and Approvals United States FCC 47CFR Part 15B Class B (DoC) UL60950-1 First Edition (cTUVus Mark) Canada ICES-003 Class B CSA C22.2 No. 60950-1 Pixelworks™ DNX™ ICs are used in this projector.
Compatible Video Formats These projectors support the high definition video and computer display formats listed here. To project images output from a computer, the computer’s video card must be set at a refresh rate (vertical frequency) that’s compatible with the projector. Some images are automatically resized using Epson’s SizeWize™ technology to display in the projector’s native format.
Computer, component video, composite video, and S-Video Mode Refresh rate (Hz) Resolution WXGA1—60 WXGA2—60 60 60 1280 × 768 1360 × 768 WSXGA60 WSXGA75 WSXGA85 60 75 85 1440 × 900 1440 × 900 1440 × 900 SXGA+60 SXGA+75 SXGA+85 60 75 85 1400 × 1050 1400 × 1050 1400 ×1050 UXGA—60 60 1600 × 1200 WSXGA+—60** 60 1680 × 1050 iMAC VGA iMAC SVGA iMAC XGA MAC13 MAC16 MAC19 MAC19-60 MAC21 117 95 75 67 75 75 60 75 640 × 480 (640 × 360*) 800 × 600 (800 × 450*) 1024 × 768 (1024 × 576*) 640 × 480 832 ×
HDMI signals Mode Refresh rate (Hz) Resolution VGA 60 640 × 480 (640 × 360*) SVGA 60 800 × 600 XGA 60 1024 × 768 SXGA SXGA 60 60 1280 × 960 1280 × 1024 SXGA+ 60 1400 × 1050 UXGA 60 1600 × 1200 SDTV (480i) SDTV (576i) SDTV (480p) SDTV (576p) HDTV (720p) HDTV (1080i) HDTV (1080p) 60 50 60 50 60/50 60/50 60/50 720 × 480 (720 × 360*) 720 × 576 (720 × 432*) 720 × 480 (720 × 360*) 720 × 576 (720 × 432*) 1280 × 720 1920 × 1080 1920 × 1080 * Letterbox signal 100 Technical Specifications
B B Notices T his appendix includes safety instructions and other important information about your projector. Important Safety Instructions Follow these safety instructions when setting up and using the projector: ■ Do not look into the lens when the projector is on. The bright light can damage your eyes. ■ Do not place the projector on an unstable cart, stand, or table. ■ Do not operate the projector on its side, or while tilted to one side.
Notices ■ Never push objects of any kind through the cabinet slots. ■ Do not use or store the projector or remote control in a hot location, such as near a heater, in direct sunlight, or in a closed vehicle. ■ Do not block the slots and openings in the projector case. They provide ventilation and prevent the projector from overheating. Do not operate the projector on a sofa, rug, or other soft surface, or set it on top of loose papers, which could block vents underneath your projector.
■ Use the type of power source indicated on the projector. Use of a different power source may result in fire or electric shock. If you are not sure of the power available, consult your dealer or power company. ■ If you use the projector in a country other than where you purchased it, use the correct power cord for that country. ■ Do not overload wall outlets, extension cords, or power strips. Do not insert the plug into a dusty outlet. This can cause fire or electric shock.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.
Index A C A/V Mute button, 46 display settings, 62, 68 A/V Mute slide closing, 46, 63, 79 opening, 35, 46, 85 Accessories, 15 to 16 Air filter cleaning, 72 to 73 ordering, 15 replacing, 73 Altitude, 63, 84, 97 Anti-theft device, 15, 19, 69 Aspect ratio, 44, 60, 95 Audio cable, 32 connecting equipment, 32 controlling volume, 48 problems, troubleshooting, 90 to 91 turning off (using A/V Mute), 46 Auto Iris setting, 58 Auto Keystone setting, 42, 61 Auto Setup setting, 59 Cables audio, 32 component-to-VGA, 1
Contrast ratio, 95 Contrast setting, 58 Control Panel Lock setting, 61, 68 to 69, 85 Custom screen, see User’s Logo D Dark Wall color mode, 43 Default settings, restoring, 57 Digital camera, connecting, 32 to 33 Dimensions, projector, 96 Direct Power On, 37 Distance from projector to screen, 20 to 22, 95 Documentation, 10 DVD player, connecting, 23 to 28 Dynamic color mode, 43 E Electrical specifications, 96 Environmental specifications, 97 Epson accessories, 15 to 16 presentation tips, 10 PrivateLine Sup
L N Lamp number of hours used, 77 ordering, 15 replacing, 74 to 77 specifications, 96 status light, 74, 83 to 84 Lamp timer, resetting, 76 to 77 Language setting, 63 Laptop computer connecting to, 29 to 31 display problems, 85 to 86 selecting source, 40 Lens Cover Timer setting, 47, 63 Lens, cleaning, 72 Light output specifications, 95 Lights, status, 83 to 84 Living Room color mode, 43 Locking buttons, 68 to 69 projector, 69 Logo, saving on projector, 66 to 68 No Signal message, 86 to 87 Noise level, 96
Projector cleaning, 72 disabling buttons, 68 to 69 distance from screen, 20 to 22, 95 installing, 19 to 22 lamp specifications, 96 options, 15 to 16 password protection, 64 to 66 positioning, 19 to 22 resolution, 95 security features, 63 to 69 specifications, 95 to 97 transporting, 79 troubleshooting, 81 to 93 turning off, 38 turning on, 35 to 37 unpacking, 18 viewing information about, 77 R Raising image, 41 Rear-screen projection, 19 to 22, 62 Registration, 15 Remote control A/V Mute button, 46 as wirele
Startup screen creating, 66 to 68 settings, 68 user’s logo, see User’s Logo Status lights, 83 to 84 Support, see Technical support S-Video cable, 15, 27 Switching picture source, 40 Sync, adjusting, 60, 89 to 90 T Technical support, 10, 92 to 93 Temperature requirements, 97 status light, 83 to 84 Temperature, color, 58 Theatre color mode, 43 Through aspect setting, 44 Tint setting, 58 Tracking, adjusting, 60, 89 to 90 Transporting projector, 79 Troubleshooting blank screen, 85 to 86 cut-off image, 87 to 88
