INSTRUCTION MANUAL Persons under age 18 are not permitted to operate or have accessibility to operate this equipment per U.S. Dept. of Labor Employment Standards Administration Fact Sheet No. ESA91-3.
TO INSURE SAFE BOTH AND TROUBLE-FREE PERFORMANCE WE STRESS THAT ALL PERSONNEL THAT WILL BE INVOLVED WITH YOUR NEW UNIVEX SLICER MUST READ INSTRUCTIONS AND UNDERSTAND BEFORE THESE ATTEMPTING TO OPERATE THIS UNIT. WE APPRECIATE YOUR COOPERATION AND YOUR BUSINESS.
8512 TABLE OF CONTENTS DESCRIPTION PAGE Table of Contonts List of Illustrations Introduction Installation Instructions 3 3 Safy Warnings 3 Operating Instructions Sharponing Instructions Operator's Care of Slicer - Cleaning Instructions Lubrication Instructions Trouble Shooting Guide Repair Instructions Including Disassembly, Replacemontand Reassembly Replacemmt Parts Warranty Information 4 4-5 s -6 7 S 9-Il 12-23 Back Cover LIST OF ILLUSTRATIONS ILLUSTRATIONS Figure Figure Figure 1 2 3 Figu
OVERALL VIEW OF MEAT SLICER 8512 MODEL 8512 Figure 1 I INDICATOR LIGHT 9 CARRIAGE ARM 2 ON-OFF SWITCH 10 ELECTRIC CORD 3 FENCE li CARRIAGEARMKNOB 4 KNiFE SHARPENER 12 ALTFO CLUTCH LEVER 5 KNIFE GUARD 13 PROTECTIVE GUARD 6 CARRIAGE 14 GRADUATED KNOB 7 ADJUSTMENT SPACER 15 8 SERIAL NAME PLATE (ON REAR) LAST SLICE DEVICE Page 2 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
INSTRUCTION MANUAL 8512 INTRODUCTION This manual contains instructions f'or the Installation, Operation, Care, Maintenance and Repair of the Meat Slicing Machine. Disassembly, Repair, Replacement and Reassembly Instructions are included. Atrouble shooting guide is provided. A complete Replacement Parts List with identifying figures is also included to facilitate identification and ordering of replacement parts.
OPERATION INSTRUCTIONS 8512 The Univex slicer is desigueci to me the cook's demand for an efliciont, sturdy slicer. The Univex slicer will give unfinling performance over a period of years, whon operated and maintained according to instrurtions contained herein. START/STOP SWITCH The slicer is started by pulling the ON/OFF switth (Figure 1 [2)) out to the ON position. A pilot light (Figure I [1)) is provided to indicate what the slicer is turned on.
8512 Warning; The following sharpening procedure wilt provide high quality sharpening results and should also be followed for safoty considerations: L WARNING: Keep away from the knife edge. Complotely close the slice adjustment (beyond "0") so that the knife edge is not exposed. The knife cutting area should be clean and free from food, especially grease. Grease will ruin the ability of a grinding stone to sharpen an edge. The stone simply will not cut.
CautIon; 4. 8512 Remove carriage assembly (Figure 1 [6])whith may be washed in a sink. Use care in washing the sharply pointed prongs on the last slice feed grip, (Figure 1 [8J). Wash this area thoroughly. A small bristle brush is recommended. Use only warm water and mild soap. Rinse carriage assembly with warm water and dry thoroughly using a clean soft cloth. Never use dotergents nor wash the slicer or any of its parts is a dishwashing mathine or the clear protective finish will be damaged.
8512 LUBRICATION INSTRUCTIONS A = Clean and apply mineral oil weekly. C= 140 WTUSDAoìI. B = Apply Petro-Gel (4400408) often as required to maintain light film. D = Lubricated for life.
8512 TROUBLESHOOTING GUIDE TROUBLE 1. Slicer will not operate. POSSIBLE CAUSE REMEDY 1.1 Electrical service down. 1.1 Check electrical service. Replace fuse or react circuit breaker as necessary. 1.2 Burned switch contacts. 1.2 Clean or replace. 1.3 Motor capacitor defective. 1.3 Replace 1.4 Burned out motor. 1.4 Remove, test, repair or replace. 2. Motor running, blade not turning, (carriage) still operating). 2.1 Broken gear 2.1 Replace gear 3 Carriage not operating (blade is operating).
REPAIR INSTRUCTIONS 8512 (including disassembly, replacement and reassembly) KNIFE (Removal) (Figure 3) I. WARNING Disconnect electrical power cord. Remove carriage assembly (Fig. 6). Remove knife guard knob (Fig. 3 [35]) and carefully remove knife guard. Loosen sharpener lock pin (Fig. 7 [26]), lift and relock in up position. WARNING Using caution to avoid the sharp knife edge, remove the four screws (Fig. 3 [15]).
Remove lama by turning counter-clockwise, 8512 Push knife support assembly from bottom and remove. 2, GEAR REPLACEMENT A. With knìfe support assembly removed, theck gear (Fig. 3 [7)) for wear. If worn, replace. B. Remove snap ring (Fig. 3 [6)). C. Pry gear off of shaft. D. Replace gear in reverse procedures. 3. BEARING REPLACEMENT Remove tapered bushing (Fig. 3 [12)). Press shaft (Fig. 3 [5)) from top of blade support assembly. C, Remove shim washers (7120040) if presont. D.
ELECTRICAL ASSEMBLY 8512 I. WARNING DISCONNECT ELECTRICAL SUPPLY Remove four rubber feet (Fig. 2 [241) and 4 extonsion legs (Fig. 2 [52 J). Remove bottom cover (Fig. 2 [19)). Remove casing cover (fig. 8 [22)). Distharge capacitors by jumping across terminals with electrically protected screwdriver. Remove reduction gear rod (Fig. 2 [34)) by removing two bolts (Fig. 2 [38)) and removing set screw at reduction gear md. Remove switth shaft (Fig. 8 [16)) by loosming nut (Fig. 8 [iS)) near switth md.
8512 BASE ASSEMBLY Figure 2 ILLUS.NO. PART NO, 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47. 48. 8512300A 6509098 8512823 8512826 8512827 8512828 8512824 8512829 8512818 8512819 6509028 6509040 8512817 1012167 8512814' 8512812 8512811 8512813 8512853 8512816 8512805 8512808 8512855 8512803A 8512516 8512803 6509143 DESCRIPTION SUPPORT, CARRIAGE, ALSO FIG.
BASE ASSEMBLY Figure 2 (CONT.) ILLUS.NO. PARTNO. 49. 50. 51. 52 53 54 55 8512865 8512867 8512637 8512248 8512866 8512869 8512871 DESCRIPTION 8512 QTY.
8512 CASTING and BLADE ASSEMBLY Figure 3 ILLUS.NO. PART NO. 8512736 8512203 8512215 8512216 8512729 8512218 8512220 8512730 8512731 1030019 8512225 8512226 8512227 Il. 86 12009* 8512229 8512228 is: 8512234 8512861 8512237 6509080 6509081 8512214 7510084 8512209 8512208 34, 35..
CASTING and BLADE ASSEMBLY 8512 Figure 3 Page 15 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
MEAT DEFLECTOR 8512 Figure 3A ILLUSNO. PART NO. 1. 2 3 4 5 6 7 8 8512030 7512156 7510342 7510346 7510343 7510344 7510345 7510347 DESCRIPTION PROTECTIVE GUARD DEFLECTOR CLIP. SPRING SCREW PAN HD MS X 10MM POST SPRING PLUNGER POST, HEADED QTY.
ARM ASSEMBLY Figure 4 ILLUS.NO. PART NO. 2. 3. 4. 5* 6. 7. 8. 9. lo. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 7510038 8512314 8512313 8512312 8512301 8512300 8512316 8512318 8512317 9512299 1053510 8512308 6509031 6509028 6509042 8512319 6509044 6509045 6509046 8512325 8512326 DESCRIPTION RUBBER SHOCK ABSORBER SPRING, DAMPER SCREW, SOC HD CAP M8-1.25 X 30MM ROD, ROUND GUIDE BUSHING 8512 QTY. 2 2 2 ARM SU000RT BAR, FRAME WASHER, EXTERNAL TOOTH SCREW BUSHING, ECCENTRIC SCREW, CAP M6-1.
8512 SLICE CONTROL ASSEMBLY Figure 5 ILLUS.NO. PART NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. * 7510067 8512527 8512526 8512525 7510065 7512076 8512839 6509028 6509071 8512511 8512512 7510073 8512326 6509131 7510061 8512518 6509046 * 8512501 8512502 8512503 8512504 8512510 6509086 8512507 8512506 8512508 8512505 8512529 8512530 8512500 DESCRIPTION BOLT, SOC HD CAP M6-1.
8512 CARRIAGE ASSEMBLY Figure 6 ILLUS NO. PART NO, 2 3 4 5 6 7 8 9 10" 11 12 13 14 15 16 17 18 19 20 8512432 8512437 8512448 8512433 8512925 8512924 8512926 6509153 8512428 8512427 8512425 8512438 8512434 RESERVED 8512431 8512927 6509038 6509058 6509059 8512439 DESCRIPTION QTY.
8512 SHARPENER ASSEMBLY Figure 7 ILLUS NO. PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 7510151 6509153 6509151 6509150 6509149 6509125 6509137 6509138 7510120 8512728 6509147 6509127 6509128 6509129 6509130 6509131 6509134 6509133 6509135 6509136 6509132 6509143 6509144 6509142 6509141 6509128 6509 126A 7510150 DESCRIPTION SHARPENER ASSEMBLY WITH COVER KNOB, COVER COVER, SHARPENER NUT, COVER SPACER SPACER.
8512 SHARPENER ASSEMBLY Figure 7 PART OF ILLUS IN FIG.
8512 ELECTRICAL ASSEMBLY 115v,60hz iph 220v, 50hz, iph Figure 8 ILLUS.NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14, 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28 29 PART NO.
8512 ELECTRICAL ASSEMBLY Figure 8 Page 23 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
8512 SCHEMATIC 115V, 60HZ, 1PH 100V. 50/60HZ, IPH Figure 9 CAPAC TOR RELAY II OREEN / YELLOW BLACK PILOT LIGHT CAPAC I TOR 3OMO. 450V ISV SWITCH 3OMFO. 450V o o I) o I GREEN WH I TE TO 115V. 50HZ.
8512 SCHEMATIC 220V, 50HZ, 1PH FIGURE 10 CARAO TOR IOMFD, 500V o GREEN / YELLOW BLACK P LOT L GHT SWITCH I ORE EN WHITE BLACK o H BLACK - TO 220V. 50HZ.
