INSTRUCTION MANUAL DURO series Slicer Persons under age 18 are not permitted to operate or have accessibility to operate this equipment per U.S. Dept. of Labor Employment Standards Administration Fact Sheet No. ESA91-3.
TO INSU RE BOTH SAFE AND TROUBLE-FREE PERFORMANCE WE STRESS THAT ALL PERSONNEL THAT WILL BE INVOLVED WITH YOUR NEW UNIVEX SLICER MUST READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE ATTEMPTING TO OPERATE THIS UNIT. WE APPRECIATE YOUR COOPERATION AND YOUR BUSINESS. SHOULD THERE BE A QUESTION OR IF WE CAN BE OF FURTHER ASSISTANCE, PLEASE CALL US, 1-603-893-6191.
6512 TABLE OF CONTENTS PAGE 'DESCRIPTION Table of Contents 1 List of Illustrations 1 Introduction 3 Installation Instruction 3 Safety Warnings 3 Operating Instructions 4-5 Sharpening Instructions 4-5 Operator's Care of Slicer - Cleaning & Lubrication 5-6 8 Mechanic's Maintenance .,. Trouble Shooting Guide Repair Instructions including Disassembly, Replacement, and Reassembly .
6512 OVERALL VIEW OF MEAT SLICER MODEL 6512 FIGURE 1 i FENCE 8 CARRIAGE ARM 2 KNIFE SHARPENER 9 GRADUATED KNOB 3 KNIFE GUARD 10 ON-OFF SWITCH 4 PROTECTIVE GUARD 11 INDICATOR LIGHT 5 LAST SLICE DEVICE 12 CARRIAGE 6 ELECTRIC CORD (NOT SHOWN) 13 SERIAL NAIVIE PLATE 7 CARRIAGE ARM KNOB (NOT SHOWN) Page 2 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
6512 INSTRUCTION MANUAL INTRODUCTION This manual contains instructìons for the Installation, Operation, Care, Maintenance and Repair of the Meat Slicing Machine. Disassembly, Repair, Replacement and Reassembly Instructions are included. A trouble shooting guide is provìded. A complete Replacement Parts List with identifying figures is also included to facilitate identification and ordering of replacement parts.
512 OPERATION INSTRUCTIONS The Univex slicer is designed to meet the cook's demand for an efficient, sturdy slicer. The Univex slicer will give un.faìling performance over a period of years, when operated and maintained according to instructions contained herein. START/STOP SWITCH The slicer is started by toggling the ON/OFF switch (Figure 1 [10]) to the ON position. A pilot light (Figure 1 [11]) is provided to indicate when the slicer is turned on.
6512 The knife cutting area should be clean and free from food, especially grease. Grease will ruin the ability of a grinding stone to sharpen an edge. The stone simply will not cut. If cleaning is necessary, follow the procedure outlined on Page 5. Loosen sharpener knob assembly (Figure 5 [28]) which bears against sharpener post, then lift sharpener assembly (Figure 1 [2]) and rotate it 1/2 turn (1800). Then force it down over the knife. Tighten sharpener knob assembly (Figure 5 [28]).
6512 Never use detergents or wash the slicer or any of its parts in a dishwashing machine or the clear protective finish will be damaged. Warning 5. Wash body of slicer using warm water and mild soap using a clean soft cloth. Under no circumstances should the slicer be hose rinsed. It is recommended that the cloth be folded over a thin wooden stick when cleaning between the fence and the knife.
6512 LUBRICATION FIGURE 2 A - Apply Petro-Gel (4400408) often as required to maintain light film. B Clean and apply mineral oil weekly.
6512 MECHANICS MAINTENANCE Every year a mechanic or service technician should perform the following inspection and carry out the respective maintenance as required: Warning: FOR SAFETY, TURN OFF SLICER AND DISCONNECT ELECTRICAL CORD. BELT DRIVE - This drive features a multi-ribbed high performance belt for long trouble-free service. Inspect belt for proper tension. If glazed or excessively worn, replace. A tensioning device automatically allows for normal belt wear-in and stretching.
6512 TROUBLESHOOTING GUIDE 6512 TROUBLE i Slicer will not operate. POSSIBLE CAUSE I.i Electrical service down. 1.2 Burned switch contacts. 1.3 Motor capacitor defective. 1 .4 Burned out motor. REMEDY 1 . i Check electrical service. Replace fuse or reset circuit breaker as necessary. 1 . 2 Replace switch. 1.3 Replace 1 .4 Remove, test, repair or replace. 2. Motor straining but will not turn (humming sound). 2.1 Belt tension too tight. 2.1 Readjust belt tension.
6512 REPAIR INSTRUCTIONS Including disassembly, replacement, and reassembly. Warning: Always turn off slicer and disconnect electrical cord before doing any maintenance or repair on the slicer. Keep guards on at all times. Keep slice adjustment fishy closed so knife edge is not exposed. Keep sharpener assembly also in place so top of knife edge is not exposed. KNIFE REPLACEMENT (FIgure 3) Warning: Disconnect electrical power cord.
6512 Reinstall pulley insert and shims that may have been present Apply liberal coating of Petro-Gel to the seal/insert interface. Reinstall knife, knife guard and sharpener in the reverse procedure outlined above. SHARPENING STONES I. Warning: Disconnect electrical cord. Unscrew sharpener knob assembly (Figure 5 [28] ). Lift up sharpening assembly (Figure 1 [2] ) and remove from slicer. Using an open end wrench, unscrew cover knob (Figure 5 [1]).
6512 Install replacement belt on knife pulley and on motor pulley shaft. DO NOT reinstall knife at this time. Reinstall motor pivot bolt. li. Reinstall spring and nuts on motor adjustment rod (Figure 3 [26] ) and tighten. It is important to make sure that the belt ìs aligned on both pulleys. Belt tension is correct when the spring is compressed to an overall length of 7/8. Connect electrìcal power cord and operate slicer to check that belt and pulley are running true.
6512 KNIFE, PULLEY AND MOTOR ASSEMBLIES FIGURE 3 ILLUS. NO. PART NO. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 6512020 6512021 6512043 6512022 6512044 6512023 6512045 6512024 6512025 6512026 6509014 8512228 1204003 8512229 6512027 6512055 6509005 6509103 6509104 1200076 1200060 6509041 1204006 6512046 6512028 6512029 6512050 6512053 6512051 1204008 6512030 1204005 6509017 6509016 8512871 QTY.
6512 KNIFE, PULLEY AND MOTOR ASSEMBLY FIGURE 3 Page 14 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
6512 FENCE, FENCE ADJUST, CARRIAGE, CARRIAGE ARM CARRIAGE ARM SUPPORT AND FEED GRIP ASSEMBLY FIGURE 4 ILLUS. NO. PART NO. DESCRIPTION QTY. FENCE MOUNTING BRACKET AND SHAFT ASSEMBLY INCLUDES NO. 1 THRU 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 6509076 6512031 6509083 SHAFT, FENCE ARM BRACKET, FENCE MOUNTING SET SCREW, M6-1.0 X 12 CUP POINT 6509081 6509082 7510080 8512234 8512206 6512033 6509024 6509038 6509037 NUT, ACORNM8-1.
6512 FENCE, FENCE ADJUST, CARRIAGE, CARRIAGE ARM CARRIAGE ARM SUPPORT AND FEED GRIP ASSEMBLY FIGURE 4 (CONT.) ILLUS. NO. PART NO. 38 39 40 41 42 6509073 6509074 6509067 6509072 6509070 DESCRIPTION QTY. SET SCREW, M6-I.0 X 20 FLAT POINT NUT, M6-1.OHEX SCREW, M6-1.0 X 18 HEX SOCKET HD NUT, M8-1.
6512 FENCE, FENCE ADJUST, CARRIAGE, CARRIAGE ARM CARRIAGE ARM SUPPORT AND FEED GRIP ASSEMBLY FIGURE 4 Page 17 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
6512 SHARPENER ASSEMBLY FIGURE 5 ILLUS. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 PART NO.
6512 BASE & SLICE ADJUSTMENT KNOB ASSEMBLY FIGURE 6 QTY. ILLUS. NO. PART NO. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 19 20 1012042 4400053 8800210 6509090 6509091 6509088 6509089 7120009 6512042 6509093 7120011 4400081 4400338 4400409 LIGHT, 125V LIGHT,230V KNOB, SLICE ADJ WASHER. SLICE ADJ NUT, SLICE ADJ STRAIN RELIEF ELECTRIC CORD, 115V ELECTRIC CORD, 230V HOLDER, CAM INSERT INSERT, CAM CAM, SLICE ADJ SET SCREW, M6-1.0 X 14, CUP POINT SWITCH, 115V, 220.
6512 WIRING DIAGRAM MODEL 6512 115V, 60HZ, 1PH, 230V, 50/60HZ, 1PH FIGURE 7 PILOT / POWER IN LIGHT C APA CIT OP N H-Q WHITE WHITE BLACK BLACK SWITCH BLACK BLACK L___ GREEN/YELLOW GREEN GANADA ONLY CIRCUIT PILOT / POWER IN ERE AK ET LIGHT CAPACITOR H-O o N BLACK BLACK 2 WHITE WHITE SWITCH BLACK BLACK WHITE BLACK GREEN BLACK GREEN/YELLOW IMPORTANT Warning: Before making electrical connections, check the specifications on the data plate to assure they agree with those of
