B6TTR-B10TTR – Page.
B6TTR-B10TTR – Page. 44 CONTENTS General Information ..................................................................................................................... 45 Technical Data And Identification ................................................................................................ 45 Installation And Commissioning ................................................................................................... 46 Preliminary Operations:…………………………………………………………………………………..
B6TTR-B10TTR – Page. 45 GENERAL INFORMATION • This manual must be delivered along with the appliance and must accompany it for its entire duration. • These instructions must be kept near the unit in an easily accessible place for easy reference over time. • Installation, commissioning and maintenance of the oven must be performed only by qualified personnel in compliance with these manufacturer instructions and with the latest current standards.
B6TTR-B10TTR – page. 46 INSTALLATION AND COMMISSIONING Preliminary operations: Once the oven has been unpacked, check it thoroughly to detect any damage. If damages due to the transport are found, search in the supply contract for the procedures to be applied in order to claim for economic coverage.
B6TTR-B10TTR – page. 47 If the distance is less or if the oven is positioned next to other units that give off heat (e.g. fryers), appropriate measures must be taken, such as placing protection against radiance . The manufacturer suggests a distance of 500 mm to ease cleaning and service. Make sure that the openings of the unit are not obstructed or covered. Attention: Once the oven has been positioned, make sure that it stands on a perfectly flat surface.
Mistral 6TTR-10TTR – page.
B6TTR-B10TTR – Page. 49 ELECTRICAL CONNECTION The electrical connection must be made only by qualified personnel. It must be in compliance with CEI requirements and specifications. The unit can be connected to the electrical network only if between them there is an omni-polar switch with at least 3 mm opening between contacts for each pole. It must be located in an easily accessible position near the oven.
B6TTR-B10TTR – Page. 50 WATER CONNECTION It is advisable to use softened water with hardness of 5°f. If the water network pressure is not within the range indicated below, a pressure reducer must be installed upstream. A. Water inlet – ¾” B. Inlet water for washing system - ¾” C. Water drain – Ø 30mm Attention: The pressure of the inlet water must be between 1 and 3 Bar, and the temperature must not exceed 30°.
B6TTR-B10TTR – Page. 51 80P CONTROL PANEL 1. 2. 3. 4. 5. Time display and Multi-timer Temperature display and fan speed Climate graphic display (Dry – Steam) Baking programmes display Programming keypad SWITCHING ON AND OFF: Once the oven has been supplied with electric power, press the “Start/Stop” key for 3 seconds. Wait for the start-up operations to finish (the Univex logo goes out on the "Programmes" display, (4).
B6TTR-B10TTR – Page. 52 SETTING THE LANGUAGE: The first thing to do is to set your language, as described below: Scroll through the Main Menu with the “+” key until reaching “Settings”. Enter the Menu with the key Scroll through the Settings Menu again with the “+” key until reaching “Language”. Enter the selection by pressing the confirm by pressing the key. Use the “+” and “-“ keys to select the desired language and key.
B6TTR-B10TTR – Page. 53 MANUAL BAKING MODE: With this programme, you can change the set parameters for a baking cycle in progress. Programmable parameters in manual mode: 1. Baking time in hours and minutes. Multi-timer on cooking programme. 2. Setting fan speed mode and semi-static baking mode. 3. Temperature of the cooking chamber. 4. Climate parameter in percentage (from 10% to 100%) of steam introduced (Steam), displayed in red.
B6TTR-B10TTR – page. 54 Please note that only when the door is closed, will the oven automatically resume baking by the setting of the next timer. If the door is opened, the oven will remain in stand-by mode. If necessary, you can add other timers during the baking programme. Proceed as follows: during the execution of the programme, press the key until the first timer is available. Press key and, through the "+" and "-" keys, set the desired time for the additional timer.
B6TTR-B10TTR – Page. 55 4. Setting the oven chamber climate: After setting the temperature value, the legends “Dry” (blue) and “Steam” (red) flash in sequence on display 3. Using the “+” key, you can increase the percentage value of steam injection during the baking cycle. The numerical scale of display 3 will be red Using the “-“ key, you can decrease the percentage value of steam injection during the baking cycle. The numerical scale of display 3 will be blue. Once the desired climate has been set, key.
B6TTR-B10TTR – Page. 56 Once the setting of the desired Steps (max 5) has been completed, the programme can be stored by pressing the operation. key for 3 seconds. The buzzer confirms the performed The next phase consists in naming the programme which has just been stored. The legend “name” appears on the display. Scroll through the letters using the “+” and “-“ keys, moving on to the next one with the key. You will have 16 characters available.
B6TTR-B10TTR – Page. 57 To start execution of the programme, press the key. During execution of the programme, the baking parameters will not be modifiable. You can stop the baking cycle before it's programmed to end simply by pressing the To exit the menu, press the control. key for 3 seconds. key.
B6TTR-B10TTR – Page. 58 before the end of the baking time, add the mozzarella cheese and desired toppings. Condition the tray with extra-virgin olive oil. bake with not perforated Teflon tray 40x60 cm increase the time parameter in minutes accordingly to the desired cooking level. Frozen Croissant do not defrost the croissants for this recipe. Bake 12 croissants per tray on perforated Teflon tray 40x60 cm increase the time parameter in minutes accordingly to the desired cooking level.
B6TTR-B10TTR – Page. 59 “COOL” – “WASH” – “FILL” PROGRAMMES: The “Programmes” mode of the electronic control also contains some non-modifiable programmes. These are stored in the firmware of the control itself and are independent from the 60 programmes available for user customizing. • “COOL” Programme: allows you to cool the oven in a short time by operating the fans also with the oven door open. Once cooled the cooking chamber, press the key for 3 seconds to stop the programme.
B6TTR-B10TTR – Page. 60 CONTACTS FOR THE DETERGENT AND RINSE AIDS TO BE USED: The following products are strongly recommended for optimal results: Detergent: Johnson Diversey Suma Auto Oven Clean D9.10 Rinse aid: Johnson Diversey Suma Auto Oven Rinse D9.
B6TTR-B10TTR – page. 61 IMPORT/EXPORT OF BAKING PROGRAMS: With the ovens of the Series Best For it is possible to export the stored programs and import new ones through external storage units, such as USB memory sticks. The USB connection to the oven occurs through the appropriate adapter card connected to the serial port on the right side of the oven. Once the connection has been made, the electronic control recognizes the peripheral device automatically and enables the appropriate management menus.
B6TTR-B10TTR – page. 62 CUSTOMIZED PROGRAMS MANAGING MODE: . The normal menu now also contains With the USB memory stick connected, press the key the Programs Management menu. The options of the normal menu will work normally. To access the programs management menu, select this option and press the key . The items described here below are disabled if the “Lock Programs” option is activated in the oven parameters.
B6TTR-B10TTR – page. 63 program, press the key for 3 seconds. The program is than exported. The display shows the writing “******” during this operation. He end of this procedure will be underlined also by an acoustic signal. Repeat the same procedure for all programs to be exported. To exit the menu “Export” press the key . The message “Operation execution error” appears in case of incorrect access to the USB memory stick.
B6TTR-B10TTR – page. 64 VISION CONTROL PANEL Once the electrical connection is completed (see page 49), at the first power supply wait about a will light indicating the minute to load the software. When the operation is completed the button possibility to turn on the control panel. Press and hold the button for 3 seconds to turn on the oven. Note: the software loading operation occurs every time the machine is re-powered after a prolonged interruption of electrical supply.
B6TTR-B10TTR – page. 65 SETTINGS MENU Access and set up of the main system settings. By pressing the icon the User enters the following screen: User’s language setting Language: Date: Time: Colour: Date setting Time setting HACCP: USB: Working parameters: Information: With the arrows and It allows to choose the background image of the display and the colours to be used in the climate bar report of all performed registrations when the machine is used.
B6TTR-B10TTR – page. 66 WORKING MODES: Chef Mode – in this menu it is possible to select various recipes setted and loaded in the Factory, or downloaded from our website and loaded in the Vision Panel with the USB key. 4 recipes per page will be visualized. Scroll the pages with the Slider and select the desired recipe with the arrow buttons Confirm with the button and . . Recipes Mode – in this menu it is possible to select various recipes saved by the User. 4 recipes per page will be visualized.
B6TTR-B10TTR – page. 67 Washing – in every working mode it is possible to access the Washing menu. This option includes 4 washing programs ,which determinates the intensity of the cleaning cycle, 1 rinsing program and 1 refilling program. Select the icon to access the following screen: Go on the desired program and press . Start the washing cycle by pressing the button . The Refilling option manages the substitution of the detergent and rinse agent.
Mistral 6TTR-10TTR – page. 68 MANUAL PROGRAMMING: Select the Manual menu . Following screen appears: – with this baking mode it is possible to divide the program to be saved into different baking steps. It will be possible to set time, temperature, fan speed and climate in an independent way for each step of the program, for a total of 10 steps for each program. Press the button . The number corresponding to the Step to be programmed will light.
B6TTR-B10TTR – page. 69 Elimination of a Step: If a Step in a program is not necessary it will be possible to cancel it with this simple operation: 7. Enter the Step mode 8. After that enter the Setting mode 9. Scrol the Steps until reaching the one to be cancelled 10. Keep the button presed for 3 seconds 11. this Step will be cancelled and the numerical sequence of the other steps that compose the program will be automatically up-dated. 12.
B6TTR-B10TTR – page. 70 screen the chosen program will appear together with the starting time. Press the button start the countdown, at whose end the program will start. It is possible to interrupt every time the delayed start by pressing the button Press the button to . until coming back to the main screen Home.
B6TTR-B10TTR – page. 71 Fan Speed parameter– it manages the set up of the desired fan speed for the baking mode to be used: 5 – high speed 4 – medium speed 3 – low speed 2 – medium speed, semi-static 1 – low speed, semi-static The semi-static mode stops the fans once the set-point temperature is reached and reactivates them at every starting of the heating elements, so that the temparature in the baking chamber remains constant.
B6TTR-B10TTR – page. 72 MULTI-TIMER MODE Multi-Timer: in this mode it is possible to find 10 programmable timers that will act only and exclusively on a single baking program. It is very useful to bake different products at the same temperature and climate but with different baking times. The oven will reach the set temperature and climate, than the timers will independently regulate the different baking cycles.
B6TTR-B10TTR – page. 73 Fig. 1 – Set the desired timers (max 59 minutes each),confirming each value with the button . After having set the desired timers, scroll the remaining ones with the arrows buttons until the parameter Temperature is visualized . After that, save all settings with the button . When the program will start with the button , the timers will start counting (Fig. 2). The timer of a different colour will be the first to end and will correspond to the tray number to be pulled out.
B6TTR-B10TTR – page. 74 By scrolling with the Slider we access also to other parameters, underlined in this screen: With the icon Timer Manual Steam it is possibleto modify just in time the steam injections seconds in the baking chamber. Confirm the modification with the button . The icon Manual Steam acts like a real button to manually inject steam when the baking program is running, accordingly to the User’s needs. Press the selected icon and change the parameters with the new desired values.
B6TTR-B10TTR – page. 75 EXECUTION OF A CHEF PROGRAM Entering the menu screen n. 1 appears with the list of available recipes. Scroll the recipes with the arrow buttons and the pages with the Slider. Select the desired recipe and press the button . After that, screen n. 2 will appear, which suggests the two main parameters to proceed with the real baking cycle. 1 Press on 2 Cooking degree: the Chef recipes are developed for a minimum baking suitable for the product to be baked (baking degree to 0).
B6TTR-B10TTR – page. 76 EXECUTION OF A RECIPE PROGRAM Entering this menu, it is possible to find all the recipes saved by the User with the programming in the manual mode. Scroll the recipes with the arrow button and the pages with the Slider. Select the desired recipe and press the button . Start the program by pressing the button . At the end of the cycle it will be possible to extend the baking time if necessary , as explained for the execution in manual mode.
B6TTR-B10TTR – page. 77 USB – import/export mode of baking programs. In the “Settings” menu , it is possible to enable or disable completely the section that belongs to the USB mode; it is also possible to protect the access recipes management with a password. Reed the paragraph “Enabling USB menu” in the next chapter for all possible options. The control is supplied with USB menu enabled by the Factory. To manage the recipes procedure act as follow: Insert the USB key in its housing above the display.
B6TTR-B10TTR – page. 78 PROCEDURE TO DOWNLOAD THE RECIPES FROM BESTFOR WEBSITE Enter the website: www.bestfor.it Enter the reserved area: Recipe Area Access the reserved area: Access the reserved area Insert the product code and the serial number to be found on the oven. Download the desired recipes files (recipes .ppf, images .Jpg, or Pdf). Now it is possible to up-load the Chef recipes (file .ppf) in the folder Univex\Recipes, the images in the folder Univex\Images, the Pdf files in the folder Univex\PDF
B6TTR-B10TTR – page. 79 6. Attach photo: Option that allows, in case it is wished, to associate a picture to the selected recipe so to identify the recipe itself (in 1:1 format with optimal advised dimensions 100KB – max 600KB). to match pictures and recipes, proceed as showed (example in Chef mode): In the Chef mode, select the recipe to which we want to match a picture (fig. 1). After that, enter the menu , select the writing (fig.
B6TTR-B10TTR – page. 80 In Recipes mode, access the menu . The here under indicated screen appears: In comparison with Chef mode, in this menu it is possible also to export the recipes saved by the User. The under menu “Export” allows to export all recipes in the folder of the Vision panel, or only the selected one. The acoustic signal will inform about operation success.
B6TTR-B10TTR – page. 81 ENABLING USB MENU As mentioned at the beginning in the previous chapter, follow this procedure to: 3. Enable or disable the USB menu 4.
B6TTR-B10TTR – page. 82 The User enters the USB section setting menu. The next screen is the following: Enabling: it allows to enable or disable the USB section in the Vision control. Select the desired option and confirm with the button is disabled, the button . In case the menu disappears from the menus Chef and Recipes. Password: it allows to protect with a password the access to the USB menu, if enabled. .
B6TTR-B10TTR – page. 83 Research –very useful mode to filter the desired recipe when there are many recipes saved, both imported or saved by the User. . Following screen will appear: Access the menu Use the arrow buttons to move through the lines and the Slider to scroll the specific letters. Confirm every digit with the button with the button . At the end press the button OK in the keyboard and confirm always . Now the display will show the filtered recipes.
B6TTR-B10TTR – page. 84 ROUTINE AND SPECIAL MAINTENANCE The unit must be checked regularly by a specialized technician. The oven is equipped with a thermal switch with manual reset which intervenes in case of overheating. To reset the thermal switch (after it has turned on), unscrew the plug on the lower left part of the oven back, then press the button to perform the reset. If the switch trips continuously, contact a specialized technician for a thorough check.
N K M J 2R 1 5JK defghijgke)glmnlofohp)efqfor 5JMS 1 2 2 1 5JKS 1 2 2 1 6JM2J1 2Ls t 6RM2u1 2 2 2 1 S4M23 TM 2c v 2T 1 JL 2w 2x s LM 2L1 1 UM 2U1y t2 s 1 cM 2c x 2 z 2s cK 2c x 2 z 2 1 2 JK 2L 2y1 5JM Q P O LM cK JK V:? V:W V:?@ V:?X V:[ V:?Z V:?Y V:\ V]:*^_`a:_&]`]**^b:aV_ V:B V:X S4M JL 6RM 6JM )EFG "$& - ((0#F! );!0#&+ 0# &<#+(0$-&?B !"#$%#! &'& !"#$(! TM cM UM H , 0
