INSTRUCTION MANUAL 4509, 4510, 4512 I g, g I i i PREP SA Persons under age 18 are not permitted to operate or have accessibility to operate this equipment per U.S. Dept. of Labor Employment Standards Administration Fact Sheet No. ESA91-3.
4509/4510/4512 TO INSU RE BOTH SAFE AND TROUBLE-FREE PERFORMANCE WE STRESS THAT ALL PERSONNEL THAT WILL BE INVOLVED WITH YOUR NEW UNIVEX SLICER MUST, READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE ATTEMPTING TO OPERATE THIS UNIT. WE APPRECIATE YOUR COOPERATION AND YOUR BUSINESS. SHOULD THERE BE A QUESTION OR IF WE CAN BE OF FURTHER ASSISTANCE, PLEASE CALL US, 1-603-893-6191.
4509/4510,4312 TABLE QE CONTENTS DESCRIPTION PAGE Table of Contents 1 List of Illustrations 1 Introduction 3 Installation Instruction 3 Safety Warnings 3-4 Operating Instructions 4 Sharpening Instructions 5 Operator's Care of Slicer Cleaning and Lubrication 6-7 Mechanics Maintenance 8 Trouble Shooting Guide 9 Repair Instructions including Disassembly, Replacement, and Reassembly 10 Replacement Parts Lists Keyed to Figure Drawings 13 - 19 Wiring Diagram 12 20 Warranty Informati
509/4510/4512 OVERALL VIEW OF MEAT SLICER MODEL 4509/4510/4512 FIGURE 1 1 FENCE 7 CARRIAGE ARM KNOB 2 KNIFE SHARPENER 8 CARRIAGE ARM 3 KNIFE GUARD 9 GRADUATED KNOB 4 PROTECTIVE GUARD 10 ON-OFF SWITCH 5 LAST SLICE DEVICE 11 CARRIAGE 6 ELECTRIC CORD (NOT SHOWN) 12 SERIAL NAME PLATE (NOT SHOWN) Page 2 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
4509/4510,4512 INSTRUCTION MANUAL INTRODUCTION This manual contains instructions for the Installation, Operation, Care, Maintenance and Repair of the Meat Slicing Machine. Disassembly, Repair, Replacement and Reassembly Instructions are included. A trouble shooting guide is provided. A complete Replacement Parts List with identifying figures is also included to facilitate identification and ordering of replacement parts.
4509/45 10/45 12 the machine is not in use, the slice adjustment knob should be turned fully back to the closed position (beyond "0") so that the knife edge is not exposed. Observe the cleaning instruction on Page 6 for best results and for safety. Also remember to always turn off the slicer and disconnect the electrical supply cord before cleaning. When slicing, always work the carriage using only the carriage arm handle (Figure 1 [8]). Do not hold or push the carriage from any other place.
4509/4510,4512 SHARPENING INSTRUCTIONS This slicer is equipped with a kmfe having a concave or hollowed surface for superior slicing quality. Of course, any knife, however superior, must be sharpened regularly and properly in order to produce not only the highest quality slices, but also to allow it to maintain its productivity. The knife sharpener (Figure 1 [2]) on this machine is a top mounted built-in mechanism, designed for simplicity and ease of use.
4509/451014512 OPERATORS CARE OF SLICER CLEANING Warning: 1. Never touch the knife edge. Always keep your hands, fingers and arms clear of knife. Warning: 2. Turn off slicer and DISCONNECT ELECTRICAL CORD before cleaning. Leave protective guard (Fig. 1 [4]) in place, 3. Turn slice adjustment knob (Figure 1 [9]) to the fully closed position (beyond "O") so that the knife edge is not exposed. 4.
4509/4510,4512 LUBRICATION & FUNCTION ChECK Warning: Turn oft' slicer and DISCONNECT ELECTRICAL CORD before lubricating. Leave protective guard (Fig. i [4]) in place. General lubrication should be performed in accordance with the lubrication instructions in Fig. 2. During this lubrication sequence, be sure to check for free operation and movement of related parts as well as for excessive wear and looseness of various parts. Be sure to check all handles and knobs for tightness.
450914510/4512 MECHANICS MAINTENANCE Every year a mechanic or service technician should perform the following inspection and carry out the respective maintenance as required: Warning FOR SAFETY, TURN OFF SLICER AND DISCONNECT ELECTRICAL CORD. BELT DRIVE This drive features a multi-ribbed high performance belt for long trouble-free service. Inspect belt for proper tension. If worn, replace. If tension requires adjustment, it may be obtained by loosening nut (Fig. 7 [2)) and turning screw (Fig.
4509/4510,4512 TROUBLESHOOTING GUIDE 4509/4510/4512 TROUBLE L Slicer will not operate. POSSIBLE CAUSE 1.1 Electrical service down. 1.2 Burned switch contacts. 1.3 Motor capacitor defective. 1.4 Burned out motor. REMEDY 1.1 Check electrical service. Replace fuse or reset circuit breaker as necessary. 1.2 Replace switch. 1.3 Replace 1,4 Remove, test, repair or replace. 2. Motor straining but will not turn (humming sound). 2.1 Belt tension too tight. 2.1 Readjust belt tension.
4509/4510/4512 REPAIR INSTRUCTiONS Including disassembly, replacement, and reassembly. Warning: Always turn off slicer and disconnect electrical cord before doing any maintenance or repair on the slicer. Keep guards on at all times. Keep slice adjustment fully closed so knife edge is not exposed. Keep sharpener assembly also in place so top of knife edge is not exposed. KNIFE REPLACEMENT (Figure 3) Warning: Disconnect electrical power cord.
4509/4510,4512 Honing (deburring) stone (Figure 8 [18) ) is removed by first unscrewing lock screw (Figure 8 [14] ) from button (Figure 8 El 5]). Gently remove button taking care to not lose the small ball bearing and spring (Figure 8 [16 & 17] ) which are inside. Unscrew nut (Figure 8 [13] ) and remove along with washer and honing stone (Figure 8 [18] ). Install new honing stone with the hollowed side toward the inside. Reattach cover and reinstall in the reverse procedures (4. through 1.).
4509/4510,4512 Pivot motor to unwrap belt from motor pulley shaft. Remove drive belt through the knife pulley opening in base casting. Install replacement belt on knife pulley and on motor pulley shaft. DO NOT reinstall knife at this time. Reinstall motor pivot rod. Tighten set screw (Figure 7 [15]). Position the pivot rod collar (End of motor shaft should be 1/16 - 1/8" away from base casting. If not slide motor along rod accordingly.) Tighten collar set screw (Figure 7 [17]),.
4509/4510/4512 HOUSING. KNIFE & FENCE ASSEMBLY FIGURE 3 ILLUS. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 PART NO.
450914510,4512 HOUSING, KNIFE & FENCE ASSEMBLY FIGURE 3 Page 14 PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor
4509/4510/4512 CARRIAGE A1M ASSEMBLY FIGURE 4 ILLUS. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PART NO. DESCRIPTION 6509017 4509053 4510053 4512033 6509080 7510035 4509065 4509054 4509089 4509055 1204004 4509069 1200076 4509056 4509057 6509074 6509073 8512308 6509054 KNOB, CARRIAGE ARM ARM, CARRIAGE 4509 ARM, CARRIAGE 4510 ARM. CARRIAGE 4512 SCREW, ARM ATTACHMENT SCREW SPRING ROD, ARM SPACER BAR, FRAME SCREW, M5-0,8 X 16 BEARING WASHER BUSHING, ARM BUSHING NUT SET SCREW SCREW, HX HD M8-1.
4509/4510,4512 CARRIAGE ASSEMBLY FIGURE 5 ILLUS. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PART NO.
4509/4510/4512 SLICE ADJUSTMENT KNOB ASSEMBLY FIGURE 6 ILLUS. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 PART NO. DESCRIPTION 4509090 6509059 4509044 4509045 1204001 6509074 1204043 4509046 1204005 6509040 4509061 7510021 6509072 4400116 6509098 4512042 KNOB, SLICE ADJ WASHER, SLICE ADJ SPRING, SLICE ADJ GUIDE SCREW SOC HD CAP M6-l.0 X 12 NUT, M6-1.0 STUD, M6-1.0 X 11 SHAFT SCREW, SOC HD CAP M6-1.0 X 20 SCREW, M6-1.
4509/4310,4512 ILLUS. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 PART NO. 4509073 4512043 4509077 4509078 6509115 6509074 1204002 4512044 4509041 1204042 6509074 4509072 4509076 1204020 4509074 7120009 7129011 4400081 4400053 8800210 1012042 6509089 4509060 6509098 4509091 4400237 4400227 MOTOR & ELECTRICAL ASSEMBLY FIGURE 7 DESCRIPTION MOTOR, 115V, 60HZ, 1PH (4509, 4510) MOTOR, 115V, 60HZ, 1PH (4512) MOTOR, 230V, 60HZ, IPH (4509, 4510) MOTOR, 230V, 50HZ, 1PH (4509, 4510) NUT, M5-0.
4509/4510/4512 SHARPENER ASSEMBLY FIGURE 8 ILLUS. NO. PART NO.
450914510,4512 WIRING DIAGRAM MODEL 4509/4510/4512 115V, 60HZ, 1PH 23QV, 60HZ, 1PH 230V, 50HZ, 1PH FIGURE 9 / POWER IN CAPACITOR OHO WHITE WHITE SWITCH BLACKE TWHITE i -1 BLACK o GREEN/YELLOW GREEN CANADA ONLY 115V, 60HZ, 1PH CIRCUI T / BREAKET POWER IN \ CAPACI TOR 2 ÇT1 SWITCH WHITE L GREEN o J WHITE WHITE BLACK BLACK BLACK MOTOR GREEN/YELLOw IMPORTANT Warning: Before making electrical connections, check the specifications on the data plate to assure they agree with those of
