® 2011 NAVIGATION SYSTEM OWNER’S MANUAL For your safety, read carefully and keep in this vehicle.
FOREWORD NISSAN NAVIGATION SYSTEM HELPDESK CONTACT INFORMATION NISSAN CONSUMER AFFAIRS DEPARTMENT For assistance or inquiries about the NISSAN Navigation System, or to order updated map data contact the NISSAN NAVIGATION SYSTEM HELPDESK at: For assistance or inquiries about the NISSAN warranty, service or general questions, contact the NISSAN Consumer Affairs Department at: . ADDRESS: P .O. Box 1588, Orem, UT 84059-992 . E-MAIL: Nissan-Navi-Info@navteq.com . WEB SITE: www.NissanNavigation.
Table of Contents Introduction 1 Getting started 2 Map settings 3 Setting a destination 4 Route guidance 5 Storing a location/route 6 Viewing technical information 7 Other settings 8 General system information 9 Troubleshooting guide 10 Index 11
1 Introduction How to use this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 For safe operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Reference symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Laser product. . . . . . . . . . . . . . . . . . . . . .
HOW TO USE THIS MANUAL This manual uses special words, symbols and icons, organized by function. Please refer to the following items and familiarize yourself with them. Basic operations of the navigation system can be performed in a similar manner for all vehicle models. However, the map screen and setting screen may be different for each model. Set the navigation system as appropriate for your vehicle.
SAFETY INFORMATION This system is primarily designed to help you reach your destination, and it also performs other functions as outlined in this manual. However, you, the driver, must use the system safely and properly. Information concerning road conditions, traffic signs and the availability of services may not always be up-to-date. The system is not a substitute for safe, proper and legal driving. Before using the navigation system, please read the following safety information.
LASER PRODUCT This navigation system is certified as a Class 1 laser product. The navigation system complies with DHHS Rules 21 CFR Chapter 1, Subchapter J. WARNING . Do not disassemble or modify this system. There are no user serviceable parts in this navigation system. . If maintenance, adjustments and operations other than those specified in this manual are attempted, injury due to laser radiation and exposure could occur.
2 Getting started Control buttons and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Start-up screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Menu screen types and how to operate. . . . . . . . . . . . . . . . . . . 2-4 Menu screens and their purposes . . . . . . . . . . . . . . . . . . . . . .
CONTROL BUTTONS AND FUNCTIONS 8
START-UP SCREEN NAV2701 1. The navigation system starts when the ignition switch is turned to the ACC or ON position. NAV2702 2. As the start-up screen is displayed, read the precautions carefully, highlight [OK] and push . INFO: If you do not push for more than 30 seconds, the status screen will be displayed. Push ,
MENU SCREEN TYPES AND HOW TO OPERATE MENU SCREENS AND THEIR PURPOSES Push , , , or to display the corresponding menu screen. How to select a menu item Example: screen 1. Tilt the joystick up and down. An item is highlighted accordingly. 2. To select the preferred menu item, highlight the item and push . INFO: Some items in the menu contain further details, which are displayed on the right side of the screen when the menu item is highlighted.
NAV3061 3. Depending on the item you selected, a detailed menu screen, a character input screen or a setting screen, etc. is displayed. On the screen displayed, make adjustments, input information, etc. accordingly. NAV2704 4. Push to return to the previous screen without applying any changes. Push
USING CONTROLS TO ADJUST VALUES, LEVELS, ETC. Use the joystick to adjust the volume of the voice guidance and the display brightness. How to adjust 1. Highlight the preferred setting item and push . The color of the corresponding adjustment item changes. 2. Use the joystick, and the value or bar indicating levels increases or decreases accordingly. 3. Push or to apply the setting.
NAV2705 MAP MENU SCREEN Current location map screen Push while the current location map screen or a scrolled map screen is displayed to display the menu corresponding to that screen. This menu allows you to quickly use helpful functions, such as setting a destination easily and searching for Points of Interest nearby. To select a menu item, use the method described in “Menu screen types and how to operate”.
. Store Tracking: Allows you to store in the Address Book the route that you have travelled from the starting point to the current location.
NAV2706 Scrolled location map screen If is pushed while a scrolled map screen is displayed, the following options are available. . New Dest: Allows you to set the destination to the location where you pushed . If a destination is already set, the location will be set as the new destination. “SETTING FROM MAP” (page 4-18) . Add to Route: Allows you to set the location where you pushed as the destination or a waypoint. This is available only when the suggested route is already set.
FUNCTIONS DISABLED WHILE DRIVING To ensure safe driving, some functions cannot be operated while driving. The on-screen functions that are not available while driving will be “grayed-out” or muted. Park the vehicle in a safe location and then operate the navigation system.
OPERATING MAPS 5 Suggested route: & Appears in bold yellow during route guidance. 6 & / Direction indicator: Indicates the direction of the map. 7 & Scale indicator: Indicates the scale of the map. 8 & NAV2708 HOW TO VIEW MAP SCREEN 3 & The navigation system displays various information on the map screen. 1 & Vehicle icon: Indicates the current vehicle location and the direction that you are traveling.
MAP SCREEN TYPES Two types of map views are available: Plan View and BirdviewTM. NAV2709 2-12 Getting started NAV2710 TM Plan View Birdview Plan View displays the map in a 2-dimensional environment similar to a road map. BirdviewTM displays the view from an elevated perspective. In BirdviewTM, it is easy to recognize an image of the route because it provides a panoramic view over a long distance.
NAV2711 SWITCHING THE MAP VIEW 1. Push while the current location map screen is displayed. NAV2712 2. Highlight [Map View] and push . NAV2713 3. Highlight the preferred map view and push . The indicator of the selected map view illuminates. “SWITCHING THE MAP VIEW” (page 3-4) 4. Push
INFO: . When you select a map view, a preview of that view is displayed on the right side of the screen. . You can also switch the map view using the following procedure. 1) Push . 2) Highlight [Navigation] and push . 3) Highlight [Map View] and push .
MOVING AROUND WITHIN A MAP You can manually move across the map to view the surrounding areas or a preferred location. 1. Tilt the joystick corresponding to the direction that you want to move across the map. Keep tilting the joystick to continuously move across the map in that direction. Once you start moving on the map, the cross pointer appears. 2. Returning to the current location map screen Push
CHANGING THE SCALE OF A MAP Push ( ) or ). A scale appears on the left side of the ( screen. To view the map in detail, push ( ). To view a wider area, push ). ( The scale will automatically disappear when ) nor ( ) has been pushed for several OUT> ( seconds. INFO: Free zoom Push and hold ( ) or ( smaller steps (free zoom).
STORING YOUR HOME LOCATION/ ADDRESS HOW TO STORE YOUR HOME If your home location is already stored in the Address Book, it can be easily retrieved to set the route to your home. The procedure to store your home location is the same as for storing any other location. “4. Setting a destination” As an example, the procedure for storing your home location by searching for a destination by address is described here. NAI0410 1. Push . NAV2714 2. Highlight [Address Book] and push .
NAV2715 3. Highlight [Home Location (Add New)] and push . 2-18 Getting started NAV3023 4. A confirmation message is displayed. Confirm the contents of the message, highlight [Yes] and push . NAV3048 5. Highlight [Street Address] and push . A character input screen is displayed.
NAV3062 6. Enter the address of your home, highlight [OK] and push . The map screen is displayed. “SETTING A STREET ADDRESS” (page 4-3) NAV3050 NAV3051 7. Using the joystick, adjust your home location if necessary. 9. A message is displayed and your home location is stored. 8. After adjusting the location, push . 10. Push
CHARACTER (letter and number) INPUT SCREEN You will have to enter alphanumeric characters when setting a destination, searching for a facility or editing the stored locations, etc. NAV3063 1. Use the joystick to highlight a character on the displayed keyboard. 2-20 Getting started NAV3064 2. Push . The highlighted character is entered.
NAV3065 3. Push or highlight [ ], and push to delete the last character entered. Push and hold to delete all the characters entered. ] and push to Highlight [ enter a space. NAV3066 4. After finishing the entry, highlight [OK] and push . INFO: You can push to return to the previous screen, but only after deleting all the characters entered.
PHONE NUMBER INPUT SCREEN You can enter a phone number as a search method to look for a point of interest. INFO: Only the locations included in the database in the map DVD-ROM can be searched by the phone number. NAV2723 1. Use the joystick to highlight a number on the displayed keyboard. 2-22 Getting started NAV2724 2. Push . The highlighted number is entered.
NAV2725 3. Push or highlight [ ], and push to delete the last number entered. Push and hold to delete all the numbers entered. NAV2726 4. After finishing the entry, highlight [Map] and push . INFO: You can push to return to the previous screen, but only after deleting all the numbers entered.
4 If the entire list cannot be displayed on the & screen, the system displays the total number of items in the list and the entry number of the selected item. Tilt the joystick upward or downward to scroll the list. 5 Highlight & and push to sort the list by shortest distance. 6 Highlight & and push to sort the list in the original order. 7 When & the list is sorted by the shortest distance, you can confirm the selected location in the preview on the right side of the screen.
SETTING A DESTINATION SEARCHING FOR A DESTINATION As an example, the method for setting an airport as the destination using [Points of Interest] is described here. NAI0410 1. Push . NAV2728 2. Highlight [Points of Interest] and push .
NAV2729 3. Highlight [Travel] and push . NAV2730 4. From the category list, highlight [AIRPORT] and push . The character input screen is displayed. NAV3067 5. Highlight [OK] and push . A list screen is displayed. INFO: You can enter the city name and facility name to narrow down your search.
NAV2732 6. Highlight the preferred airport from the list and push . NAV2733 INFO: By selecting [By Distance], you can sort the list by the shortest distance. The position of the selected location is displayed in the preview on the right side of the screen. NAV2734 7. The selected destination is displayed at the center of the map. Highlight [OK] after confirming the location of the displayed destination, and push .
NAV2735 INFO: Even after setting a destination, you can adjust the location of the destination, store the route, etc. if necessary. “OPERATIONS AFTER SETTING A DESTINATION” (page 4-45) 2-28 Getting started NAV2736 STARTING ROUTE GUIDANCE After setting the destination and performing route calculation, the suggested route is displayed. 1. Highlight [Start] and push . NAV2737 2. Once route guidance is started, the system navigates you through the guide points using visual and voice guidance.
NAV2738 3. When approaching a guide point, the system automatically changes to the split screen and shows an enlarged view of the intersection in the left screen. NAV2739 4. When arriving at the destination, route guidance automatically ends.
DELETING A ROUTE To delete a route already set, use the following procedure. If you delete a route, the destination is also deleted. NAI0411 1. Push . 2-30 Getting started NAV2740 2. Highlight [Cancel Route Guidance] and push .
SETTING THE VOICE GUIDANCE TURNING VOICE GUIDANCE ON/OFF You can activate or deactivate voice guidance and adjust the volume. NAV2741 3. A confirmation message is displayed. Highlight [Yes] and push . NAI0413 1. Push . INFO: If a route is cancelled, [Cancel Route Guidance] changes to [Resume Route Guidance]. Highlight [Resume Route Guidance] and push to reactivate the cancelled route. This is available only until a new route is set.
ADJUSTING VOICE GUIDANCE VOLUME You can adjust the volume of voice guidance. NAV3052 2. Highlight [Guidance Voice] and push . The indicator illuminates if voice guidance is activated. 2-32 Getting started NAI0413 1. Push .
NAV3053 2. Highlight [Guidance Volume] and push . NAV3054 3. Adjust the voice guidance volume using the joystick.
MEMO 2-34 Getting started
3 Map settings Map types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Plan View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 BirdviewTM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Switching the map view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Available views . . . . . .
MAP TYPES Two types of map views are available: Plan View and BirdviewTM. PLAN VIEW Plan View displays the map in a 2-dimensional environment similar to a road map. NAV2708 Screen information 1 & 3 & Vehicle icon: Indicates the current vehicle location and the direction that you are traveling. 2 & Guide point: Indicates a guide point on the route. 3-2 Map settings GPS indicator: Indicates the GPS reception condition of signals from the satellites.
tion and start route guidance. 5 Suggested route: & Appears in bold yellow during route guidance. 6 & / Direction indicator: Indicates the direction of the map. 7 & Scale indicator: Indicates the scale of the map. 8 & Arrow: Indicates the distance to the next guide point and the turning direction at that guide point. NAV2746 BIRDVIEW TM TM Birdview displays the map from an elevated perspective.
SWITCHING THE MAP VIEW The map view can be changed between Plan View and BirdviewTM. The map can also be displayed in the split screen mode. NAV2711 1. Push while the current location map screen is displayed. 3-4 Map settings NAV2712 2. Highlight [Map View] and push .
AVAILABLE VIEWS . Plan View: Switches to Plan View. . BirdviewTM: Switches to BirdviewTM. . Split (Plan View): Changes to the split screen mode and both halves display maps in Plan View. . Split (BirdviewTM): Changes to the split screen mode and the left half displays the map in Plan View and the right half displays the map in BirdviewTM. INFO: NAV2747 3. Highlight the preferred map view and push . The indicator of the selected map view illuminates. 4.
NAV2748 NAV2750 Split (Plan View) INFO: You can also set the map view using the following procedure. 1) Push . 2) Highlight [Navigation] and push . 3) Highlight [Map View] and push .
MOVING A MAP The operations for moving across the map are different between Plan View and BirdviewTM. PLAN VIEW Tilt the joystick corresponding to the direction that you want to move across the map. Keep tilting the joystick to continuously move across the map in that direction. Once you start moving across the map, the cross pointer appears.
BIRDVIEWTM The joystick allows movement in the following ways. Keep tilting the joystick to continuously move across the map in that direction. 1 Rotates the map clockwise. & 2 Rotates the map counterclockwise. & 3 Moves the cross pointer on the map upward. & 4 Moves the cross pointer on the map down& ward. Once you start moving on the map, the cross pointer appears.
RETURNING TO THE CURRENT VEHICLE LOCATION Push
MAP SCROLLING INFORMATION Information about the location, on which the center of the cross pointer is placed by scrolling on the map, can be set to be displayed. 1. Push . NAV3055 2. Highlight [Navigation] and push . 3-10 Map settings NAV2752 3. Highlight [Map Scrolling Information] and push .
NAV2753 4. Highlight the preferred information item and push . The indicator of the selected information item illuminates. Available information items: . Address Book Icons . Destination/Waypoint Icons . Latitude/Longitude Info NAV2754 5. Push
CHANGING THE SCALE OF A MAP Push ( ) or ). A scale appears on the left side of the ( screen. To view the map in detail, push ). ( To view a wider area, push ). ( The scale will automatically disappear when ) nor neither ( ) has been pushed for ( several seconds. INFO: Free zoom Push and hold ( ) or ( smaller steps (free zoom).
MAP SCALE The following scales are available depending on the map view. . In Plan View: Widest (1/51,200,000) to the most detailed (1/5,000) . In BirdviewTM: Widest (1/20,480,000) to the most detailed (viewpoint height at 1/25,000) Scale level of the Plan View display Map scale Actual distance 1:51.2 million 400 miles (640 km) 1:5.12 million 32 miles (64 km) 1:1.
Scale level of the BirdviewTM display Map scale Distance between grids 1:20.48 million 160 miles (256 km) 1:5.12 million 32 miles (64 km) 1:2.56 million 16 miles (32 km) 1:1.
OTHER SETTINGS FOR THE MAP SCREEN Other settings are also available for the map screen, such as changing the map direction, splitting the screen, etc. SETTINGS OF HEADING/LONG RANGE MAP VIEW You can change the map direction (orientation) in Plan View or change the position of the vehicle icon to view a wider area in the traveling direction. These settings are available only in the Plan View or Split (Plan View) mode. NAV4173 1. Push while the current location map screen is displayed. NAV4174 2.
Available map orientations NAV2760 3. Highlight the preferred map orientation and push . The indicator of the selected map orientation illuminates. . North Up: North is set at the top of the map. . Heading Up: The traveling direction is set at the top of the map. . Long Range Map View: The vehicle icon is located slightly lower than the center of the screen. This offers a wider view in the traveling direction. . BirdviewTM Angle: This changes the BirdviewTM angle.
CHANGING THE BIRDVIEWTM ANGLE This changes the BirdviewTM angle. This setting is available only in the BirdviewTM or Split (BirdviewTM) mode. NAV2763 NAV2764 Long Range Map View INFO: If the map orientation is switched, the icon displayed in the lower left corner is also switched. : North Up INFO: You can also set the orientation of the map using the following procedure. 1) Push . 2) Highlight [Navigation] and push . 3) Highlight [Heading] and push .
NAV4173 1. Push while the current location map screen is displayed. NAV2765 NAV4174 2. Highlight [Heading] and push . 3. Highlight [Birdview . TM Angle] and push INFO: This setting is available only when the map view is set to the BirdviewTM or Split (BirdviewTM) mode.
NAV2764 INFO: NAV2766 TM 4. Adjust the Birdview angle by moving the ] or [ ]. cursor in the direction of [ 5. Push
CHANGING THE SCALE OF THE LEFT SCREEN When the split screen is displayed, you can change the scale of the left screen. NAV2711 1. Push while the current location map screen is displayed. 3-20 Map settings NAV2712 2. Highlight [Map View] and push .
NAV2767 3. Highlight [Change Map Scale for Left] and push . INFO: [Change Map Scale for Left] is displayed only when the map view is in the Split (Plan View) or Split (BirdviewTM) mode. NAV2768 4. Highlight [Map Scale] and push . Adjust the map scale by moving the cursor in the direction of [+] or [−]. Use the joystick to adjust the scale of the map. After finishing the setup, push or to apply the scale setting. 5. Push
MAP ICONS Some landmarks in the surrounding area can be displayed as icons on the screen. DISPLAYING LANDMARK ICONS This allows you to display or hide the landmark icons by type. Landmark icons that can be displayed . Restaurant . Gas Station . Hotel . ATM . Rest Area 3-22 Map settings NAV2711 1. Push while the current location map screen is displayed. NAV2769 2. Highlight [Landmark Icons] and push .
NAV2770 3. Highlight the preferred icon and push . The icon display setting toggles on and off each time you push . The indicator of the selected icon illuminates. NAV2771 4. Push
MAP SYMBOLS This navigation system uses symbols to display facilities.
NAI0417 Map settings 3-25
Road color The road types are differentiated by colors.
4 Setting a destination Destination screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Basic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Setting a street address/residence as the destination. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Setting a Street Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DESTINATION SCREEN There are several methods you can use to set your destination. Understand the advantages of each method and select the best method for finding and setting your destination. BASIC OPERATION 1. Push . 2. Highlight the preferred destination setting method and push . NOTE: There may be a case that you cannot search by pointing at “Street Address”, “Intersection” and “Point of Interest (POI)”. This is because the map DVDROM data of Nunavut in Canada is undeveloped.
SETTING A STREET ADDRESS/ RESIDENCE AS THE DESTINATION . Others — Phone Number: Searches for a destination by the telephone number. — Nearby Places: Searches for a business/location near your vehicle. — Previous Starting Point: Sets the previous starting point as the destination. — Stored Route: Selects a stored route. — Freeway Entrance/Exit: Searches for a destination from a freeway entrance/exit. — Intersection: Searches for a destination from intersections.
NAV3069 NAV3068 INFO: Character input screen for Street Address 1 Region: & The region previously entered is automatically displayed. It can be changed. 2 City: & By default, all cities in the region are available. Route calculation conditions can be narrowed down by entering the name of the city. 4-4 Setting a destination 3 Street: & Enter the name of a street. 4 House No. : & A house number can be entered. & Symbols/A-Z: 5 Symbol keys are displayed by highlighting [Symbols] and pushing .
NAV3070 4. Enter the name of the street. After finishing the entry, highlight [OK] and push . A list of cities is displayed. NAV2829 5. Highlight the correct city of the destination from the list and push . INFO: If the list of cities is too long, choose a city by selecting , highlight [City] and push . NAV2830 6. The selected destination is displayed at the center of the map. Highlight [OK] after confirming the location of the displayed destination, and push .
NAV2831 INFO: Even after setting a destination, you can adjust the location of the destination, store the route, etc. “OPERATIONS AFTER SETTING A DESTINATION” (page 4-45) 4-6 Setting a destination NAV3071 Changing the region 1. From the Street Address destination entry screen, highlight [Region] and push to change the region. NAV3072 2. Highlight the preferred region and push . A character input screen is displayed.
NAV3073 Specifying a city 1. From the Street Address destination entry screen, highlight [City] and push to narrow down the route calculation conditions by entering the name of the city. NAV3074 2. Enter the name of the city, highlight [OK] and push . A list screen is displayed. NAV2836 3. Highlight the city of the destination from the list and push . INFO: . . Highlight [All Cities] and push to include all cities in the region as the route calculation condition.
NAV2787 SETTING A CITY CENTER 1. Push . 2. Highlight [Others] and push . NAV2837 3. H i g h l i g h t [ C i t y C e n t e r ] a n d p u s h . A character input screen is displayed. NAV3075 INFO: Character input screen for City Center 1 Region: & The region previously entered is automatically displayed. It can be changed. 2 City: & By default, all cities in the region are available. Route calculation conditions can be narrowed down by entering the name of the city.
3 Symbols/A-Z: & Symbol keys are displayed by highlighting [Symbols] and pushing . Alphabet keys are displayed by highlighting [A-Z] and pushing . NAV3076 4. Highlight [City] and push to narrow down the route calculation conditions by entering the name of the city. Enter the name of the city, highlight [OK] and push . A list screen is displayed. NAV2840 5. Highlight the preferred destination from the list and push .
NAV2841 INFO: By selecting [By Distance], you can sort the list by the nearest distance. 4-10 Setting a destination NAV2842 6. The selected destination is displayed at the center of the map. Highlight [OK] after confirming the location of the displayed destination, and push . The system sets the destination to the selected location and starts calculating a route. NAV2843 INFO: Even after setting a destination, you can adjust the location of the destination, store the route, etc.
NAV3077 Changing the region 1. From the City Center destination entry screen, highlight [Region] and push to change the region. NAV3078 2. Highlight the preferred region and push . A character input screen is displayed.
NAV2787 SETTING AN INTERSECTION 1. Push . 2. Highlight [Others] and push . 4-12 Setting a destination NAV2846 3. H i g h l i g h t [ I n t e r s e c t i o n ] a n d p u s h . A character input screen is displayed.
5 Symbols/A-Z: & Symbol keys are displayed by highlighting [Symbols] and pushing . Alphabet keys are displayed by highlighting [A-Z] and pushing . NAV3079 INFO: Character input screen for Intersection 1 Region: & The region previously entered is automatically displayed. It can be changed. 2 City: & 3 1st Street: & Enter the name of the 1st street of the destination intersection. 4 2nd Street: & Enter the name of the 2nd street of the destination intersection.
NAV3080 4. Enter the name of the 1st street. After finishing the entry, highlight [OK] and push . A list screen is displayed. 4-14 Setting a destination NAV2849 5. Highlight a street as the 1st street from the list and push . NAV3081 6. Enter the name of the 2nd street. After finishing the entry, highlight [OK] and push . A list screen is displayed.
NAV2851 7. Highlight a street as the 2nd street from the list and push . NAV2852 8. The selected destination is displayed at the center of the map. Highlight [OK] after confirming the location of the displayed destination, and push . The system sets the destination to the selected location and starts calculating a route. NAV2853 INFO: Even after setting a destination, you can adjust the location of the destination, store the route, etc.
NAV3082 Changing the region 1. From the Intersection destination entry screen, highlight [Region] and push to change the region. 4-16 Setting a destination NAV3083 2. Highlight the preferred region and push . A character input screen is displayed. NAV3084 Specifying a city 1. From the Intersection destination entry screen, highlight [City] and push to narrow down the route calculation conditions by entering the name of the city.
NAV3085 2. Enter the name of the city, highlight [OK] and push . A list screen is displayed. NAV2858 3. Highlight the city of the destination from the list and push . A character input screen is displayed. INFO: . . Highlight [All Cities] and push to include all cities in the region as the route calculation condition. Highlight [Last 5 Cities] and push to display 5 cities recently set as destinations.
SETTING FROM MAP This allows you to search for a destination by scrolling the map, and then have the system calculate a route to the destination. NAV2859 1. Scroll the map, place the cross pointer over the preferred location, and push . NAV2860 2. Highlight [New Dest] and push . INFO: INFO: . . 4-18 Setting a destination Adjust the map scale to search for a location more effectively.
NAV2861 3. The system sets the destination to the selected location and starts calculating a route. NAV2862 INFO: If you set the destination on a freeway, a confirmation message is displayed.
SETTING A STORED LOCATION AS THE DESTINATION The following setting methods are available when setting the destination to your home or any location stored in the Address Book. . Setting your home This allows you to set your home as the destination and have the system calculate a route. It is useful especially when you are searching for a route to return to your home. “STORING A LOCATION” (page 6-2) .
NAV2775 3. Highlight [Home Location] and push . NAV2776 4. A confirmation message is displayed, and the system sets your home as the destination. NAV2777 5. Your home is displayed at the center of the map, and the system starts calculating a route. INFO: If you have not stored your home yet, the system will automatically display a screen for storing it.
NAV2774 SETTING FROM ADDRESS BOOK 1. Push . 2. Highlight [Address Book] and push . A list screen is displayed. 4-22 Setting a destination NAV2778 3. Highlight the preferred location from the list and push . NAV2779 INFO: Selecting [Sort List] displays a list of various sort functions. To use the sort functions, stored locations must be set in advance.
NAV2781 NAV2780 1 Sort by number: & The Address Book entries are displayed in ascending numerical order. 2 Sort by name: & The Address Book entries are displayed in alphabetic order. 3 Sort by icon: & 4. The selected destination is displayed at the center of the map. Highlight [OK] after confirming the location of the displayed destination, and push . The system sets the destination to the selected location and starts calculating a route.
NAV2782 INFO: Even after setting a destination, you can adjust the location of the destination, store the route, etc. “OPERATIONS AFTER SETTING A DESTINATION” (page 4-45) 4-24 Setting a destination NAV2783 SETTING A PREVIOUS DESTINATION 1. Push . 2. Highlight [Previous Destinations] and push . NAV2784 3. Highlight the preferred destination from the list and push .
NAV2785 4. The selected destination is displayed at the center of the map. Highlight [OK] after confirming the location of the displayed destination, and push . The system sets the destination to the selected location and starts calculating a route. NAV2786 INFO: Even after setting a destination, you can adjust the location of the destination, store the route, etc. “OPERATIONS AFTER SETTING A DESTINATION” (page 4-45) NAV2787 SETTING THE PREVIOUS STARTING POINT 1. Push . 2.
NAV2788 3. Highlight [Previous Starting Point] and push . 4-26 Setting a destination NAV2789 4. The starting point of the route of the previous route guidance is displayed at the center of the map. Highlight [OK] after confirming the location of the displayed destination, and push . The system sets the destination to the selected location and starts calculating a route. NAV2790 INFO: Even after setting a destination, you can adjust the location of the destination, store the route, etc.
NAV2787 SETTING FROM STORED ROUTES 1. Push . NAV2791 3. Highlight [Stored Routes] and push . A list screen is displayed. NAV2792 4. Highlight the preferred route from the list and push . The route to the destination is set. 2. Highlight [Others] and push . INFO: The stored route includes only locations (destination and waypoints) and route calculation conditions, not the route itself.
SETTING A FACILITY AS THE DESTINATION When you are setting the destination to a facility, the following methods are available. . Setting a Point of Interest This allows you to find a facility by type, and then have the system calculate a route to that destination. Specify the region and city of the destination to find it more quickly. . Setting a Freeway Entrance/Exit This allows you to set the destination to an entrance or exit of a freeway, and then have the system calculate a route. .
NAV2794 4. Highlight the subcategory and push . A character input screen is displayed.
6 Symbols/A-Z: & Symbol keys are displayed by highlighting [Symbols] and pushing . Alphabet keys are displayed by highlighting [A-Z] and pushing . NAV3086 INFO: Character input screen for Points of Interest 1 Region: & The region previously entered is automatically displayed. It can be changed. 2 City: & By default, all cities in the region are available. Route calculation conditions can be narrowed down by entering the name of the city.
NAV3087 5. Highlight [Name] and push . Enter the name of the destination facility. NAV3088 6. After finishing the entry, highlight [OK] and push . A list screen is displayed. NAV2798 7. Highlight the preferred destination facility from the list and push . INFO: If the list of a POI names is too long, enter more characters to further reduce the number of matches.
NAV2799 INFO: By selecting [By Distance], you can sort the list by the nearest distance. The position of the selected location is displayed in the preview on the right side of the screen. 4-32 Setting a destination NAV2800 8. The selected destination is displayed at the center of the map. Highlight [OK] after confirming the location of the displayed destination, and push . The system sets the destination to the selected location and starts calculating a route.
NAV3089 Changing the region 1. From the Point of Interest destination entry screen, highlight [Region] and push to change the region. NAV3090 2. Highlight the preferred region and push . A character input screen is displayed. NAV3091 Specifying a city 1. From the Point of Interest destination entry screen, highlight [City] and push to narrow down the route calculation conditions by entering the name of the city.
NAV3092 2. Enter the name of the city, highlight [OK] and push . INFO: . . Highlight [All Cities] and push to include all cities in the region as the route calculation condition. Highlight [Last 5 Cities] and push to display 5 cities recently set as destinations. 4-34 Setting a destination NAV2806 3. Highlight the city of the destination facility from the list, and push . A character input screen is displayed.
Category list Restaurant Shopping Restaurant all African, American, Austrian, Balkan, Barbecue/Southern, Belgian, Bistro, Bohemian, Brewpub, British isles, Cajun/Caribbean, Californian, Canadian, Chinese, Continental, Dutch, East European, Fast food, Filipino, French, German, Greek, Grill, Hawaiian/Polynesian, Hungarian, Indian, Indonesian/ Malaysian, International, Italian, Japanese, Jewish/Kosher, Korean, Latin American, Maltese, Mexican, Middle Eastern, Oriental, Other, Pizza, Polish, Portuguese, Russ
Airport Border crossing Bus station Commuter rail station Ferry terminal Hotel Travel Automobile club Rental car agency Rest area Ski resort Tourist attraction Tourist information Train station Auto service & maintenance 4-36 Setting a destination Hotel all America Inn & Suites, Amerihost (Cendant), Amerisuites, Baymont Inn & Suites, Best Western, Candlewood Suites, Clarion, Country Hearth Inn, Country Inn Suites (Carlson Group), Courtyard by Marriott, Crossland Motel, Crowne Plaza, Days Inn, Double Tr
Banking ATM Bank Hospital Community City hall, Community center, Convention/Exhibition center, Court house, Historical monument, Hospital, Library, Marina, Museum, Police station, Park/Recreation area, School, Sports center, Sports complex, Performing arts, Higher education Leisure Amusement park, Bowling center, Casino, Movie theater, Convention/Exhibition center, Golf course, Historical monument, Ice skating rink, Marina, Museum, Nightlife, Park/Recreation area, Ski resort, Sports center, Sports comp
NAV2787 SETTING A FREEWAY ENTRANCE/ EXIT 1. Push . 2. Highlight [Others] and push . 4-38 Setting a destination NAV2807 3. Highlight [Freeway Entrance/Exit] and push . A character input screen is displayed. NAV3093 4. Select a region and enter the name of the freeway. 5. After finishing the entry, highlight [OK] and push .
NAV2809 6. Highlight the freeway of the destination from the list, and push . NAV2810 7. Highlight [Entrance] or [Exit] and push . A list screen is displayed. NAV2811 8. Select the preferred destination from the list. The position of the selected location is displayed in the preview on the right side of the screen. Then, push .
NAV2812 INFO: By selecting [By Distance], you can sort the list by the nearest distance. 4-40 Setting a destination NAV2813 9. The selected destination is displayed at the center of the map. Highlight [OK] after confirming the location of the displayed destination, and push . The system sets the destination to the selected location and starts calculating a route. NAV2814 INFO: Even after setting a destination, you can adjust the location of the destination, store the route, etc.
NAV2787 SETTING BY PHONE NUMBER INFO: . If the area code of the specified telephone number does not exist in the map data, the system will not search for the location. . Only the locations included in the database in the map DVD-ROM can be searched by the phone number. Personal phone numbers cannot be used to search for a location. NAV2815 3. Highlight [Phone Number] and push . The telephone number input screen is displayed. NAV2816 4. Enter the telephone number including the area code. 5.
NAV2817 6. The selected destination is displayed at the center of the map. Highlight [OK] after confirming the location of the displayed destination, and push . The system sets the destination to the selected location and starts calculating a route. 4-42 Setting a destination NAV2818 INFO: Even after setting a destination, you can adjust the location of the destination, store the route, etc. “OPERATIONS AFTER SETTING A DESTINATION” (page 4-45) NAV2787 SETTING A NEARBY PLACE 1. Push . 2.
NAV2819 3. Highlight [Nearby Places] and push . NAV2820 4. Highlight the preferred destination Points of Interest and push . A list screen is displayed. INFO: NAV2821 5. Highlight the preferred destination from the list, and push . The position of the selected location is displayed in the preview on the right side of the screen. If there are any particular Points of Interest that you intend to use frequently, you can store them in the list of nearby Points of Interest.
NAV2822 INFO: If the suggested route is already set, by highlighting [Show Along Route] and pushing , the system displays only the Points of Interest located along the route. 4-44 Setting a destination NAV2823 6. The system sets the destination to the selected location and starts calculating a route. INFO: If the route is already set, the selected location becomes a waypoint.
OPERATIONS AFTER SETTING A DESTINATION The following operations are available after you set a destination. INFO: The menu will not be displayed if you select, [Stored Route] or [Nearby Places] from the Destination menu. NAV2863 AVAILABLE SETTING ITEMS . OK: Sets the destination. If the route is already set, the location becomes the new destination, and the route is recalculated. . Alter Location: Displays a map screen where you can adjust the location of the destination. .
ADJUSTING THE LOCATION OF THE DESTINATION You can adjust the location of the destination by moving the cross pointer across the map. NAV2864 1. Set the destination using an appropriate method. 2. Highlight [Alter Location] and push . 4-46 Setting a destination NAV2865 3. Adjust the location by moving the cross pointer across the map and push . The location of the destination is modified.
ADDING ADDITIONAL DESTINATIONS TO A ROUTE Even after the route is already set, you can add a searched location as a new destination or waypoint to that route. If the route has not been set, [Add to Route] cannot be selected. NAV2866 1. Set the destination using an appropriate method. NAV2867 3. Highlight [Destination] or [Waypoint] and push . 2. Highlight [Add to Route] and push .
VIEWING INFORMATION ABOUT THE SEARCHED LOCATION Information (street address and phone number) about Points of Interest stored in the map DVDROM data can be displayed. NAV2868 1. Set the destination using an appropriate method. 2. Highlight [POI Info] and push . 4-48 Setting a destination NAV2869 3. Information about the location is displayed. 4. Push or highlight [Back], and push to return to the previous screen.
STORING A LOCATION A searched location can be stored in the Address Book. Then it can be easily retrieved and set as a destination (or waypoint). NAV2870 1. Set the destination using an appropriate method. 2. Highlight [Store Location] and push . NAV2871 3. The location is stored in the Address Book. The corresponding icon is displayed at the set location on the map.
MEMO 4-50 Setting a destination
5 Route guidance Procedures after setting a destination . . . . . . . . . . . . . . . . . . . . . 5-2 Available items after setting a destination . . . . . . . . . . . . . 5-2 Starting route guidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Selecting a route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Confirming a route. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PROCEDURES AFTER SETTING A DESTINATION After you set a destination using an appropriate method and select [OK], the system starts calculating a route to the destination. Select the preferred setting item and push . INFO: If you have not performed any operations on the system for several seconds, [Start] is automatically selected, and the system starts route guidance. NAV2872 AVAILABLE ITEMS AFTER SETTING A DESTINATION . Start: Starts route guidance to the selected destination.
NAV2873 NAV2874 NAV2875 STARTING ROUTE GUIDANCE SELECTING A ROUTE Available route conditions 1. Highlight [Start] and push . Route guidance starts. 1. Highlight [More Routes] and push . 1 Short. Time (Blue): & 2. Highlight the preferred route condition and push . 2 Min. FWY (Red): & 3. Push to return to the previous screen. Prioritizes by the shortest time. Minimizes the use of freeways. 3 Short. Dist. (Green): & Prioritizes by the shortest distance. INFO: .
NAV2876 CONFIRMING A ROUTE 1. Highlight [Route Info] and push . 2. Highlight the preferred information item and push . 3. Push to return to the previous screen. 5-4 Route guidance NAV2877 Available information . Preview: Allows you to confirm the route by scrolling on the map manually. “USING ROUTE PREVIEW” (page 527) . Simulation: Allows you to view a simulation of the route.
ADDING A DESTINATION OR WAYPOINT Before starting route guidance, you can add destinations and/or waypoints. A total of 6 destinations or waypoints can be set. NAV2878 1. Highlight [Add Way Pt.] and push . NAV2879 2. Set additional destinations or waypoints and push . INFO: The method of searching for a location is the same as the one for a destination. “4.
NAV2880 3. The selected location is displayed at the center of the map. Highlight [Add to Route] after confirming the location and push . INFO: You can modify the location by selecting [Alter Location]. The method of adjusting a location is the same as the one for a destination. “ADJUSTING THE LOCATION OF THE DESTINATION” (page 4-46) 5-6 Route guidance NAV2881 4. Highlight [Destination] or [Waypoint] and push .
ABOUT ROUTE GUIDANCE After setting the route, select [Start] to begin route guidance. Throughout route guidance, the system navigates you through the guide points using visual and voice guidance. CAUTION The navigation system’s visual and voice guidance is for reference purposes only. The contents of the guidance may be inappropriate depending on the situation. When driving along the suggested route, follow all traffic regulations (e.g., oneway traffic).
GUIDANCE SCREENS AND PREVIEW MODE Route guidance displays map screens and various information according to the situation. NAV2882 When route guidance starts, the Small Turn Arrow on Map is displayed in the upper left corner of the map screen. This arrow indicates the turning direction at the next guide point (corner or intersection). The distance is also displayed. At the top of the screen, the distance to the next guide point and the name of the next street to turn on to are displayed.
NAV2884 NAV2885 Junction guidance Turn list While driving on a freeway, when the vehicle is approximately 1 mile (approximately 2 km) from a junction, the system automatically switches to the split screen and displays an enlarged view of the junction (3D) in the left screen. After passing the junction, the system automatically returns to the full screen mode. To switch to the full screen mode while the enlarged junction view is displayed, push
ROUTE SETTING During route guidance, you can modify the route conditions or confirm the route information. Set the appropriate route condition according to your purpose. BASIC OPERATION 1. Push . 2. Highlight the preferred setting item and push . 3. Push
. Route Information: Allows you to confirm the route by the route information or simulation. “CONFIRMING A ROUTE” (page 526) . Guidance Settings: You can set various guidance information to be displayed during route guidance and activate or deactivate route and/or voice guidance.
SETTING CONDITIONS FOR THE ROUTE CALCULATION . Route Priority Settings Allows you to set the priority for the route calculation. . Detailed Route Priorities Allows you to set detailed route conditions. “DETAILED ROUTE PRIORITIES” (page 5-13) ROUTE PRIORITY SETTINGS The route can be recalculated after changing the route calculation conditions anywhere along the route. Basic operation 1. Push . 2. Highlight [Route Priority] and push . 3. Highlight the preferred condition and push .
DETAILED ROUTE PRIORITIES Detailed conditions can be set for the route calculation. Basic operation 1. Push . 2. Highlight [Route Priority] and push . 3. Highlight [Detailed Route Priorities] and push . 4. Highlight the preferred condition and push . The indicator for the selected condition illuminates. 5. When the current location map screen or route setting screen is displayed, the system recalculates a route with the set conditions. NAV2888 Available setting items .
INFO: . The recalculated route may not be the shortest route because the system prioritizes easy-to-drive roads for safety reasons. . If you set the route conditions from [Route Priority], all sections in the route are subject to the same route conditions even though you have set different route conditions for different sections in [Edit Route]. . If [Use Time Restricted Roads] is deactivated, the system calculates a route without any consideration of the regulations concerning the time or day of the week.
CHANGE/EDIT ROUTE You can calculate a detour for a section of the route, edit the route or store the route. BASIC OPERATION 1. Push . 2. Highlight [Change/Edit Route] and push . 3. Highlight the preferred setting item and push . 4. Push
. Store Current Route: A calculated route can be stored. A maximum of 5 routes can be stored. Stored routes can be easily retrieved and set as the suggested route.
INFO: NAV2890 SETTING A DETOUR ROUTE 1. Highlight [Detour] and push . NAV2891 . When the vehicle has deviated from the suggested route, [Detour] cannot be selected. . If the system cannot calculate a detour with the specified conditions, it displays the previous suggested route. . If the vehicle is traveling very fast, the detour route may start from a location that the vehicle has already passed. 2. Highlight a detour distance and push .
NAV2892 RECALCULATE ROUTE 1. Highlight [Recalculate Route] and push . 5-18 Route guidance NAV2893 2. A message is displayed, and the route is recalculated. NAV2894 3. Set the route conditions. After finishing the setting, highlight [Start] and push .
NAV2895 EDITING A ROUTE 1. Highlight [Edit Route] and push . 2. Highlight the preferred condition and push . 3. Push to return to the previous screen. Push
“Changing route calculation conditions” (page 5-24) 5 Allows you to add a destination. & “Setting a destination or waypoint” (page 5-20) Setting a destination or waypoint You can add a destination or waypoint to the route already set. A total of 6 destinations or waypoints can be set. Adding a destination or waypoint 6 Allows you to add a waypoint. & “Setting a destination or waypoint” (page 5-20) NAV2897 1. Highlight [Destination] or [Waypoint] and push .
NAV2898 2. Set a destination or waypoint. The method of searching for a destination or waypoint is the same as the one for a destination. “4. Setting a destination” NAV2899 3. The selected location is displayed at the center of the map. Highlight [Add to Route] after confirming the location and push . INFO: Even after setting a destination/waypoint, you can adjust the destination/waypoint location, store the route, etc. “OPERATIONS AFTER SETTING A DESTINATION” (page 4-45) NAV2900 4.
Editing/deleting a destination or waypoint You can modify or delete the destination or waypoint already set. INFO: If you modify or delete a location when a suggested route is already set, the prior suggested route will be recalculated accordingly. NAV2901 1. Highlight a destination or waypoint that is already set and push . 5-22 Route guidance NAV2902 2. Highlight [Alter Locn.] to modify the location and push .
NAV2903 3. Highlight [Delete] and push to delete the location. NAV2904 4. A confirmation message is displayed. Confirm the contents of the message, highlight [Yes] and push . The destination or waypoint is deleted from the route. INFO: If the destination is deleted, the final waypoint of the route becomes the destination.
Changing route calculation conditions Each section of the route between waypoints can have different route calculation conditions. After setting these conditions, you can recalculate the entire route. NAV2905 1. Highlight the preferred section of the route to the destination or waypoint and push . NAV2906 2. Highlight the preferred condition and push .
INFO: . The recalculated route may not be the shortest route because the system prioritizes easy-to-drive roads for safety reasons. . If you set the route conditions from [Route Priority], all sections in the route are subject to the same route conditions even though you have set different route conditions for different sections in [Edit Route]. NAV2907 3. The system automatically recalculates a route according to the conditions set.
CONFIRMING A ROUTE When the suggested route is displayed after calculation, you can confirm the route information or simulate the suggested route. BASIC OPERATION 1. Push . 2. Highlight [Route Information] and push . 3. Highlight the preferred item and push . NAV2909 Available items . Turn list: Displays the details of the suggested route. “USING TURN LIST” (page 5-27) .
NAV2910 USING TURN LIST 1. You can confirm the information (e.g., intersections) on the route to the destination by scrolling the screen using the joystick. 2. Push
NAV2912 CONFIRMING BY SIMULATION 1. Highlight the preferred key and push . : Pauses the simulation. : Resumes the simulation. : Ends the simulation. 5-28 Route guidance 2. Push to cancel the simulation and return to the current location map screen. INFO: During simulation, you can change the map scale by pushing ( ) or ).
ROUTE GUIDANCE SETTINGS You can set various guidance information to be displayed during route guidance and activate or deactivate route and/or voice guidance. BASIC OPERATION 1. Push . 2. Highlight [Guidance Settings] and push . 3. Highlight the preferred item and push . 4. Push to return to the previous screen. Push
. Set Average Speeds: Allows you to set an average vehicle speed for each type of road, which is reflected in the calculation of the required time to the destination.
NAV2914 VISUAL GUIDANCE SETTINGS 1. Highlight [Guidance Screen Default] and push . 2. The indicator of the selected type of guidance illuminates. NAV2915 Intersection Map: Enlarged intersection view INFO: Push
VOICE GUIDANCE SETTINGS You can set how many times voice guidance is repeated. NAV2917 1. Highlight [Voice Announcements] and push . NAV2918 2. Highlight [Twice] or [Three Times] and push . The indicator for the selected number of repetitions illuminates. 3. Push
SET AVERAGE SPEEDS You can calculate the required time to the destination based on the set vehicle speeds. Basic operation 1. Highlight [Set Average Speeds] and push . 2. Highlight the preferred item and push . 3. Use the joystick to make an adjustment. The speed can be increased/decreased by 5 MPH (5 km/h). 4. After finishing the setting, push or to activate the setting. 5. Push to return to the previous screen. Push
. Reset: Sets the average vehicle speeds to the default values.
DELETING/REACTIVATING A ROUTE You can delete a route already set at any time. If you delete a route, the destination and waypoints are also deleted. It is also possible to reactivate the route that you deleted. NAV2920 DELETING A ROUTE 1. Push . 2. Highlight [Cancel Route Guidance] and push . NAV2921 3. A confirmation message is displayed. Highlight [Yes] and push . The route is deleted along with the destination and waypoints.
NAV2922 REACTIVATING A ROUTE 1. Push . 2. Highlight [Resume Route Guidance] and push . NAV2923 3. A confirmation message is displayed. Highlight [Yes] and push . The route you have deleted is reactivated. INFO: If you set a new route, the deleted route cannot be reactivated.
6 Storing a location/route Storing a location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Storing a location by searching . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Storing the current vehicle location. . . . . . . . . . . . . . . . . . . . . 6-5 Storing a location by moving the map . . . . . . . . . . . . . . . . . 6-6 Avoid area settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 Storing a route . .
STORING A LOCATION Locations that you often visit can be stored in the Address Book. The stored locations can be easily retrieved to set them as a destination or waypoint. INFO: . The Address Book can store up to 100 locations. . New information placed in the same storage position will overwrite the old data. STORING A LOCATION BY SEARCHING After you have searched for a location as previously described, you can store the location for future use. 1. Push . NAV3055 2.
NAV2930 3. Highlight [Address Book] and push . NAV2931 4. Highlight [Stored Location] and push . NAV2932 5. Highlight [Home Location (Add New)] or [None (Add New)] and push .
NAV2933 6. Highlight the appropriate method to search for a location and push . “4. Setting a destination” NAV2934 7. When your preferred location is displayed at the center of the map, confirm the location and push . A message is displayed, and the location is stored in the Address Book. INFO: You can adjust a location by selecting [Alter Location] using the same method as the one for a destination.
NAV2924 STORING THE CURRENT VEHICLE LOCATION 1. Push at the current vehicle location. NAV2925 2. Highlight [Store Location] and push . A message is displayed, and the current vehicle location is stored in the Address Book. NAV2926 3. Push
NAV2927 STORING A LOCATION BY MOVING THE MAP 1. Move to the preferred location on the map and push . NAV2928 2. Highlight [Store Location] and push . A message is displayed, and the location is stored in the Address Book. INFO: The location is stored in the first available position number in the Address Book list. 6-6 Storing a location/route NAV2929 3. Push
AVOID AREA SETTINGS An Avoid Area can be stored. The Avoid Area is an area that you want to exclude from a route, such as a road that is always congested. Once you store Avoid Areas, the system avoids those areas when calculating a route. Up to 10 Avoid Areas can be stored. 1. Push . NAV3055 2. Highlight [Navigation] and push . NAV2936 3. Highlight [Avoid Area Settings] and push . INFO: You can also access and store an Avoid Area from the Address Book.
NAV2937 4. Highlight [None (Add New)] and push . INFO: A maximum of 5 Avoid Areas can be stored. “DELETING A STORED ITEM” (page 6-28) NAV2938 5. Highlight the appropriate method to search for a location and push . “4. Setting a destination” NAV2939 6. Set the following items for the searched location. Available setting items . Rename . Alter Location . Resize Area . FWY . Delete 7. After finishing the setting, highlight [OK] and push .
NAV4175 Rename 1. A character input screen is displayed. 2. Enter the preferred name. NAI0419 3. Highlight [OK] and push . Alter Location 1. Using the joystick, adjust the location of the Avoid Area. 2. After adjusting the location, push .
Resize Area Select the range from 5 available levels. After selecting the range, push . INFO: Push ( ) or ) to change the scale of the map.
INFO: If you set an Avoid Area at the current vehicle location, the system will not provide route guidance. NAV2942 FWY If you want to include freeways in the Avoid Area, push to illuminate this indicator. NAV2943 The Avoid Area is displayed in green if it includes a freeway or in blue if it does not include freeways.
STORING A ROUTE A calculated route can be stored. A maximum of 5 routes can be stored. Stored routes can be easily retrieved and set as the suggested route. INFO: Stored route includes only locations (destination and waypoints) and route calculation conditions, not the route itself. 1. Push . NAV2944 2. Highlight [Change/Edit Route] and push . 6-12 Storing a location/route NAV2945 3. Highlight [Store Current Route] and push .
INFO: . The route is stored in the first available position number in the store current route list. . A maximum of 5 routes can be stored. “DELETING A STORED ITEM” (page 6-28) . If you have not set any waypoints on the route, the route cannot be stored. NAV2946 4. A confirmation message is displayed. Confirm the contents of the message, highlight [Yes] and push . The current route is stored. NAV2947 INFO: You can also store a route using the following procedure. 1) Push .
STORING A TRACKED ROUTE You can store the route you have traveled up to the current location. A maximum of 5 tracked routes can be stored. A tracked route must not exceed 12 miles (20 km) in distance. The stored tracked route can be displayed on the map as necessary. 1. Push . NAV2948 2. Highlight [Store Tracking] and push . INFO: A maximum of 5 tracked routes can be stored. “DELETING A STORED ITEM” (page 6-28) NAV2949 3. A confirmation message is displayed.
EDITING THE ADDRESS BOOK Items stored in the Address Book can be modified. You can edit these settings to make the navigation system more useful. BASIC OPERATION 1. Push . 2. Highlight [Navigation] and push . 3. Highlight [Address Book] and push . 4. Highlight the preferred item and push . 5. Push to return to the previous screen. Push
. Delete Stored Items: Deletes a stored location or route. “DELETING ALL STORED ITEMS” (page 6-31) NAV2951 EDITING THE STORED HOME AND LOCATION 1. Highlight the preferred stored home location or stored location and push . INFO: Selecting [Sort List] displays a list of various sort functions. To use the sort functions, stored locations must be set in advance. “MINOR ADJUSTMENT OF THE STORED HOME AND LOCATIONS” (page 6-17) 6-16 Storing a location/route NAV2952 2.
MINOR ADJUSTMENT OF THE STORED HOME AND LOCATIONS When you select [Edit], you can edit the following items of the home or stored location. . Show Icon on Map . Name (only for stored locations) . Icon . Sound . Direction . Distance . Phone No. . Group (only for stored locations) . Entry Number (only for stored locations) NAV2953 NAV2954 Show Icon on Map Name (only for stored locations) Displays the home icon or the stored location icon on the map. Changes the name of a stored location. 1.
NAV2955 2. Enter the preferred name for the stored location. “CHARACTER (letter and number) INPUT SCREEN” (page 2-20) 3. Highlight [OK] and push . The name is stored. 6-18 Storing a location/route NAV2956 Icon Changes the icon of the home or stored location to the preferred one. By changing the icons, you can utilize the [By Icon] option of the sort function more effectively. 1. Highlight [Icon] and push . A list of icons is displayed. NAV2957 2.
Icon List: NAI0420 Storing a location/route 6-19
Sound list: None Chime Melody Sound Dog Cat Wave NAV2958 Sound Sets the tone of the arrival alarm that sounds when the vehicle approaches the home or a stored location. 1. Highlight [Sound] and push . A sound list is displayed. 6-20 Storing a location/route NAV2959 2. Highlight the preferred alarm tone by scrolling the list using the joystick. Then push . The indicator of the selected alarm tone illuminates.
NAV2960 Direction Sets the alarm to sound when approaching from a specific direction. 1. Highlight [Direction] and push . The home or stored location is displayed at the center of the map. NAV2961 2. Set the direction that sounds the alarm using the joystick. Then push . The selected direction is set. INFO: NAV2962 Distance Sets the alarm to sound when reaching a specific distance to the home or stored location. 1. Highlight [Distance] and push .
NAV2963 2. Highlight the preferred distance option and push . The indicator of the selected distance illuminates. Available distance options: . 150 feet (50 m) . 300 feet (100 m) . 1000 feet (300 m) . 1500 feet (500 m) INFO: Once you set the direction and distance to sound an alarm, the system will sound the alarm when the vehicle icon passes a half circle outline on the map, as shown in the figure.
NAV2965 2. Enter the telephone number of the home or stored location. “PHONE NUMBER INPUT SCREEN” (page 2-22) 3. Highlight [OK] and push . The telephone number is stored. NAV3094 Group (only for stored locations) This allows you to group the stored locations. By grouping the stored locations, you can utilize the [By Group] option of the sort function more effectively. NAV2967 2. Highlight the preferred group and push .
NAV3095 Entry Number (only for stored locations) Swaps the position numbers of any two stored locations in the list. 1. Highlight [Entry Number] and push . A list of stored locations is displayed. 6-24 Storing a location/route NAV3096 2. Highlight the stored locations you want to swap and push . The position numbers of the selected stored locations are swapped.
NAV2970 EDITING THE STORED ROUTE 1. Highlight the preferred stored route and push . 2. Tilt the joystick to the right to select the Edit screen. The setting items are highlighted. 3. Highlight the preferred item and push . 4. After finishing the setting, highlight [OK] and push . INFO: If you select [None (Add New)], the system stores the current route. NAV2971 Available setting items . Rename: Changes the name. “CHARACTER (letter and number) INPUT SCREEN” (page 2-20) .
NAV2972 EDITING THE STORED TRACKING 1. Highlight the preferred stored tracked route and push . The [Show] indicator for the stored tracked route illuminates, and the route is displayed on the map. Tilt the joystick to the right to highlight [Edit]. INFO: . . Current tracking is displayed up to 62 miles (100 km). Stored tracking is displayed up to 12 miles (20 km). 6-26 Storing a location/route NAV2973 2. Highlight the preferred item and push . Available setting items (Current tracking) .
NAV2975 EDITING THE AVOID AREA 1. Highlight the preferred Avoid Area and push . 2. Highlight the preferred item and push . The setting method is the same as the one for the Avoid Area setting. “AVOID AREA SETTINGS” (page 67) INFO: If you select [None (Add New)], you can add an Avoid Area. “AVOID AREA SETTINGS” (page 6-7) NAV2976 Available setting items . Rename: Changes the name. . Alter Location: Adjusts the location of the Avoid Area. . Resize Area: Adjusts the range of the Avoid Area. .
DELETING A STORED ITEM You can delete locations and routes stored in the Address Book. Two deletion methods are available, deleting an individual item and deleting all stored items. NOTE: Deleted items cannot be restored. Before deleting an item, always make sure that the item is truly not necessary. NAV2977 DELETING A STORED ITEM INDIVIDUALLY 1. Push . 2. Highlight [Navigation] and push . 3. Highlight [Address Book] and push .
NAV2979 5. Highlight the preferred location/route for deletion and push . NAV2980 6. Highlight [Delete] and push . NAV2981 7. A confirmation message is displayed. Confirm the contents of the message, highlight [Yes] and push . The stored item is deleted from the Address Book.
NAV2982 DELETING AN INDIVIDUAL ITEM ON THE MAP 1. Align the cross pointer over the preferred stored location for deletion by moving on the map. Then push . 6-30 Storing a location/route NAV2983 2. Highlight [Delete] and push . NAV2984 3. A confirmation message is displayed. Confirm the contents of the message, highlight [Yes] and push . The stored item is deleted from the Address Book.
NAV3055 DELETING ALL STORED ITEMS 1. Push . NAV2930 3. Highlight [Address Book] and push . NAV2985 4. Highlight [Delete Stored Items] and push . 2. Highlight [Navigation] and push .
NAV2987 NAV2986 5. Highlight the preferred item for deletion and push . Items that can be deleted . Delete Home Location: Deletes the home location. . Delete Stored Locations: Deletes all stored locations. . Delete Stored Routes: Deletes all stored routes. 6-32 Storing a location/route . . . . . Delete Current Tracking: Deletes the current tracked route. Delete Stored Tracking: Deletes all stored tracked routes. Delete Avoid Areas: Deletes all stored Avoid Areas.
CUSTOMIZING NEARBY PLACES You can change the categories used for searching Points of Interest nearby. The modified list of Points of Interest can be used for searching for a location using [Nearby Places]. “SETTING A NEARBY PLACE” (page 442) NAV3055 1. Push . 2. Highlight [Navigation] and push . NAV2988 3. Highlight [Nearby Places Custom Settings] and push .
NAV2989 4. Highlight the preferred item and push . The main category list is displayed. NAV2990 5. Highlight a main category and push . The sub category list is displayed. NAV2991 6. Highlight a sub category and push . The category setting is modified. 7. Push
7 Viewing technical information Viewing information about current vehicle location. . . . . . 7-2 Basic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Viewing GPS current location information . . . . . . . . . . . . . . . . 7-3 Basic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Viewing navigation system version information. . . . . . . . . . . 7-4 Basic operation . . . . . . . . . . . . . .
VIEWING INFORMATION ABOUT CURRENT VEHICLE LOCATION This allows you to display the information about the vehicle location on the route when driving according to route guidance. BASIC OPERATION 1. Push . 2. Highlight [Route Information] and push . 3. Highlight [Where am I?] and push . 4. Push to return to the previous screen. Push
VIEWING GPS CURRENT LOCATION INFORMATION This allows you to display GPS information, such as the positioning status, latitude/longitude, altitude and satellite locations. BASIC OPERATION 1. Push . 2. Highlight [Navigation] and push . 3. Highlight [GPS Satellite Info] and push . 4. Push to return to the previous screen. Push
VIEWING NAVIGATION SYSTEM VERSION INFORMATION BASIC OPERATION 2 Latitude/Longitude: & 1. Push . Displays the latitude/longitude. 2. Highlight [Navigation] and push . 3 Approx Altitude: & 3. Highlight [Navigation Version] and push . Displays the approximate altitude. 4 Positioning status: & (green) (gray) 7-4 It indicates that satellites are available. It indicates that satellites are being searched for.
8 Other settings Settings screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Basic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Display settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3 System settings screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6 Language and unit settings. . . . . . . . . . . . . . . .
SETTINGS SCREEN The navigation system can be customized to make it easier for you to use. BASIC OPERATION 1. Push . 2. Highlight the preferred setting item and push . NAV3056 Available setting items . Display: “DISPLAY SETTINGS” (page 8-3) . Vehicle Electronic Systems: Refer to the Owner’s Manual of your vehicle. . System Settings: Allows you to adjust the time setting, language/measurement unit setting and ON/OFF setting of beeps used in the system. 8-2 Other settings .
. Guidance Volume: Adjust the volume level of voice guidance by tilting the joystick in the direction of [+] or [−]. DISPLAY SETTINGS This menu allows you to turn on and off the display and adjust the image quality. Basic operation 1. Highlight [Display] and push . 2. Highlight the preferred adjustment item and push . 3. Use the joystick to adjust to the preferred setting. 4. After setting, push or to apply the setting. 5. Push to return to the previous screen.
NAV3100 Display off To turn off the display, push and turn > the [Display off] indicator on, and hold < (Day/Night) for more than 2 seconds. NAV3101 When any button is pushed with the display off, the display turns on. The display will automatically turn off 3 seconds after the operation is finished. > (Day/Night) To turn on the display, push < for more than 2 seconds. NAV3102 Brightness Adjust the display brightness by tilting the joystick in the direction of [+] or [−].
NAV3103 Contrast Map Background Adjust the display contrast by tilting the joystick in the direction of [+] or [−]. Push < > (Day/Night) to choose the background color. Adjust the background color brightness by tilting the joystick in the direction of [+] or [−]. INFO: The preview of the map screen is displayed on the upper portion of the screen, if the previous screen showed a map. NAV3003 NAI0480 Bright background color INFO: When you turn the headlight switch on, the background color changes.
SYSTEM SETTINGS SCREEN Allows you to set system settings such as language/measurement unit setting. Basic operation 1. Push . 2. Highlight [System Settings] and push . 3. Highlight the preferred adjustment item and push . 4. Push to return to the previous screen. Push
LANGUAGE AND UNIT SETTINGS This allows you to change the language and measurement unit used in the system. NAV3031 Language settings 1. Highlight [Language/Units] and push . NAV3032 2. Highlight the preferred setting item and push . The indicator light of the selected item illuminates.
NAV3033 3. A message is displayed. Confirm the contents of the message. After confirming the message, highlight [Yes] and push . NAV3034 4. The program loading screen is displayed, and the system initiates language setting. Upon completion, the start-up screen is automatically displayed. CAUTION Do not change the ignition switch position while changing the language. Doing so may cause a system malfunction.
NAV3031 Unit settings 1. Highlight [Language/Units] and push . NAV3035 2. Highlight [Unit] and tilt the joystick to the right or left or push to highlight the preferred unit. The indicator of the selected unit illuminates. Available units — US: mile, MPH, 8F, MPG — Metric: km, km/h, 8C, L/100 km 3. Push to return to the previous screen. Push
CLOCK SETTINGS This allows you to change the clock settings. Basic operation 1. Highlight [Clock] and push . 2. Highlight the preferred adjustment item. 3. Use the joystick to adjust to the preferred setting. 4. After setting, push or to apply the setting. 5. Push to return to the previous screen. Push
. Select Time Zone: Select an appropriate time zone from the list that appears when you select this item.
MAP COLOR SETTINGS This allows you to change the map color. 1. Push . NAV3005 2. Highlight [Navigation] and push . 3. Highlight [Map Color Settings] and push . NAV3006 4. Highlight the preferred map color and push . The indicator light of the selected color illuminates. Available map colors Warm: Sets warm colors for the map coloring. Cool: Sets cool colors for the map coloring.
ADJUSTING THE CURRENT VEHICLE LOCATION If the vehicle icon indicating the current vehicle location is not located in the correct position, you can correct the position of the vehicle icon on the map screen. INFO: . Regardless of the map view setting, the map is displayed in Plan View when adjusting the position of the vehicle icon. . When you correct the position of the vehicle icon, the map is automatically displayed in the North Up mode.
NAV3018 5. Adjust the direction of the vehicle icon using the joystick. After adjusting the direction of the vehicle icon, push . 8-14 Other settings NAV3019 6. A message is displayed, and the adjusted vehicle location is stored.
RESET ALL NAVIGATION SETTINGS TO DEFAULT This allows you to restore various settings (display, volume level, etc.) to the default settings. INFO: The memory contents, such as the stored locations, will not be deleted. NAV3020 1. Push . 2. Highlight [Navigation] and push . NAV3021 4. A confirmation message is displayed. Confirm the contents of the message, highlight [Yes] and push . 3. Highlight [Reset ALL navigation settings to default] and push .
MEMO 8-16 Other settings
9 General system information Features of this navigation system . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 Route guidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 Points of Interest (POI) directory. . . . . . . . . . . . . . . . . . . . . . . . 9-2 Address book. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 Avoid area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FEATURES OF THIS NAVIGATION SYSTEM ROUTE GUIDANCE The main features of the NISSAN Navigation System are visual guidance and voice guidance in selected map coverage areas. Utilizing a network of GPS (Global Positioning System) satellites, the NISSAN Navigation System tracks your location on the map and navigates you to a preferred location. Once you set the destination in a map coverage area, the NISSAN Navigation System will calculate a route from your current location to your destination.
CURRENT VEHICLE LOCATION DISPLAY OF CURRENT VEHICLE LOCATION This navigation system combines the data obtained from the vehicle (by gyro sensor) and from GPS (Global Positioning System) satellites to calculate the current location of the vehicle. This position is then displayed throughout route guidance to a destination. NAV2710 NAV2704 BIRDVIEWTM VOICE GUIDANCE Two map types, 2-dimensional Plan View and 3dimensional BirdviewTM, are available in the NISSAN Navigation System.
the system will automatically adjust the position of the vehicle icon using GPS signals. Receiving signals from GPS satellites The reception of GPS signals can be weak, depending on the environment. Vehicles in the following areas/environments may not receive GPS signals (indicator color: gray).
INFO: The GPS antenna is located on the instrument panel inside the vehicle. Do not place any objects, especially mobile phones or transceivers, on the instrument panel. Because the strength of the GPS signal is approximately one billionth of that of TV waves, phones and transceivers will affect or may totally disrupt the signal. NAI0424 * NAI0503 * Under multi-layered highways In a canyon Display of GPS information GPS information can be displayed.
INCORRECT DISPLAY OF VEHICLE POSITION The following cases may affect the display accuracy of the vehicle’s position or traveling direction. The accuracy will return to normal if the driving conditions return to normal. NAI0426 * When there is a similar road nearby. * When the vehicle is traveling in an area with a grid pattern road system. NAI0428 * When the vehicle is passing through a large Yshaped intersection/junction. * When the vehicle is traveling on a continuous, slowly curving road.
NAI0430 * When the vehicle is traveling on a road with repeating S-shaped curves. * When the vehicle is on a loop bridge. NAI0434 NAI0432 * When the vehicle is on a snow-covered or unpaved road. * When repeatedly turning left or right, or driving in zigzags. NAI0431 * When the vehicle is rotated on a parking lot turntable while the ignition switch is off. * When driving on a road not displayed on the map screen or a road that has been changed due to additional construction or other reasons.
. If the vehicle icon position does not return to normal even after driving for a while, correct the vehicle icon position manually. “ADJUSTING THE CURRENT VEHICLE LOCATION” (page 8-13) DETAILED MAP COVERAGE AREAS (MCA) FOR THE NAVIGATION SYSTEM NAI0436 * When the GPS positioning accuracy is low. INFO: . The vehicle icon may be misaligned when starting the vehicle just after starting the engine. . The vehicle icon may also be misaligned if different sized tires or tire chains are installed. .
ROUTE CALCULATION WHEN A GRAY ROAD IS DISPLAYED ON THE MAP . When you are driving on a road displayed in gray after the vehicle has deviated from the suggested route during route guidance, automatic rerouting may not start immediately. . The navigation system does not provide route guidance for roads displayed in dark green.
. If waypoints are set, the system calculates multiple routes between waypoints simultaneously, and the following may result. — If one section between waypoints cannot be calculated, none of the route will be displayed. — The route may not connect completely at some waypoints. — The route may require a U-turn close to some waypoints. . Route calculation may not be completed in the following cases. — If there is no main road within a range of 1.5 miles (2.
ROUTE GUIDANCE INFO: The announcement of the street name during route guidance is available only when English is set as the language for the system. Street names are not announced if French is set for the system. BASICS OF VOICE GUIDANCE . Route guidance provided by the navigation system does not take carpool lane driving into consideration, especially when carpool lanes are separated from other road lanes.
NAI0437 NAI0438 Notification of an intersection on an ordinary road Notification of consecutive intersections on an ordinary road 1. “In about one quarter mile (400 meters), right (left) turn.” When the road has three or more consecutive intersections ahead, voice guidance will announce the following. 2. “Right (left) turn ahead.” 1. “In about one quarter mile (400 meters), right (left) turn, then left (right) turn.” 2. “Left (right) turn ahead, then right (left) turn.
NAI0441 Notification of a freeway exit 1. “In about one mile (1.6 kilometers), exit on your right.” NAI0440 Notification of a freeway junction 2. “Take the second exit on your right.” 3. “Keep to the right (left) onto (road number and direction).” 1. “In about one mile (1.6 kilometers), keep to the right (left) onto (road number and direction), then in about one quarter mile (400 meters) keep to the right (left).” 2.
Notification when approaching the destination Ordinary road: When approaching the destination, voice guidance will announce, “You have arrived at your destination. Ending route guidance.” To finally reach your destination, refer to the map screen. Dark green road: After passing the last turning point on a suggested route, voice guidance will announce, “The route to your destination includes roads through incomplete map areas. Voice guidance will not be provided in these areas.
MAP DVD-ROM . The displayed street names may sometimes differ from the actual names, or “UNKNOWN STREET NAME” may be displayed. . Voice guidance is not available when the [Guidance Voice] indicator is not illuminated. . Voice guidance will start when the vehicle enters the suggested route. Refer to the map for directions to the starting point of the route. . When approaching a waypoint, voice guidance will announce, “You have arrived at waypoint 1 (2, 3, 4,...).
END-USER TERMS The Map Data Disc (“Data”) is provided for your personal, internal use only and not for resale. It is protected by copyright, and is subject to the following terms (this “End- User License Agreement”) and conditions which are agreed to by you, on the one hand, and NAVTEQ North America, LLC (“NT”) and its licensors (including their licensors and suppliers) on the other hand.
or in communication with vehicles capable of vehicle navigation, positioning, dispatch, real time route guidance, fleet management or similar applications; or (b) with, or in communication with, including without limitation, cellular phones, palmtop and handheld computers, pagers, and personal digital-assistants or PDAs. Warning.
defined at 48 C.F.R. (“FAR”) 2.101, is licensed in accordance with this End-User License Agreement, and each copy of Data delivered or otherwise furnished shall be marked and embedded as appropriate with the following “Notice of Use,” and be treated in accordance with such Notice: MAP DVD-ROM DRIVE LOCATION NOTE: Please be very careful when handling the disc.
DISC REPLACEMENT CAUTION . The included map DVD-ROM is designed specifically for your navigation system. Do not use it in another system as it could cause a malfunction. . Do not allow the system to get wet. Excessive moisture, such as spilled liquids, may cause the system to malfunction. . Before inserting the map DVD-ROM disc, confirm that there is no disc in the slot. NAI0449 1. To insert a disc: Place the disc in the slot. It will be drawn in automatically. You do not have to push it in all the way.
as illustrated. . Never attempt to use a DVD-ROM that has been cracked, deformed or repaired using adhesive. Doing so may damage the equipment. . Handle the DVD-ROM carefully to avoid contamination or flaws. Otherwise, the data may not be read properly. NAI0451 HOW TO HANDLE THE DVD-ROM CAUTION . Handle a DVD-ROM by its edges. Never touch the surface of the disc. . To clean a disc, wipe the surface from the center to the outer edge using a clean, soft cloth. Do not wipe the disc using a circular motion.
HOW TO HANDLE THE DISPLAY The display is a liquid crystal display and should be handled with care. WARNING Never disassemble the display. Some parts utilize extremely high voltage. Touching them may result in serious personal injury. CHARACTERISTICS OF A LIQUID CRYSTAL DISPLAY . If the temperature inside the vehicle is especially low, the display will stay relatively dim or the movement of the images may be slow. These conditions are normal.
MEMO 9-22 General system information
10 Troubleshooting guide Customer assistance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2 Basic operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3 Vehicle icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4 Map DVD-ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CUSTOMER ASSISTANCE For assistance or inquiries about the NISSAN Navigation System, contact the NISSAN NAVIGATION SYSTEM HELPDESK. See the contact information on the inside front cover of this manual.
BASIC OPERATIONS Symptom No image is displayed. No voice guidance is available. or The volume is too high or too low. No map is displayed on the screen. Possible cause The brightness is at the lowest setting. Possible solution Adjust the brightness of the display. The display is turned off. Push and hold < display. The volume is not set correctly, or it is turned off. Adjust the volume of voice guidance.
VEHICLE ICON Symptom Possible cause Possible solution Names of roads and locations differ between Plan view and BirdviewTM. This is because the quantity of the displayed information is reduced so that This is not a malfunction. the screen does not become too crowded. There is also a chance that names of the roads or locations may be displayed multiple times, and the names appearing on the screen may be different because of a processing procedure.
Symptom The location of the vehicle icon is misaligned from the actual position. Possible cause Possible solution When using tire chains or replacing the tires, speed calculations based on Drive the vehicle for a while (at approximately 19 the speed sensor may be incorrect. MPH for about 30 minutes) to automatically correct the vehicle icon position. If this does not correct the vehicle icon position, contact a NISSAN dealer.
MAP DVD-ROM Symptom The message “Error” appears. Possible cause The map DVD-ROM is dirty or damaged. Possible solution Check the map DVD-ROM and wipe it clean with a soft cloth, following the cautions and instructions on page 9-20. If you see any damage, replace the map DVD-ROM.
ROUTE CALCULATION AND VISUAL GUIDANCE Symptom Possible cause Possible solution Waypoints are not included in the auto reroute calculation. Waypoints that you have already passed are not included in the auto reroute calculation. If you want to go to that waypoint again, you need to edit the route. Route information is not displayed. Route calculation has not yet been performed. Set the destination and perform route calculation. You are not driving on the suggested route.
Symptom An indirect route is suggested. Possible cause The system may suggest an indirect route because route calculation does not take into consideration some areas such as narrow streets (gray roads). The landmark information does not correspond to the actual information. Reset the destination to a main or ordinary road, and recalculate the route. This may be caused by insufficient or incorrect data on the DVD-ROM. Updated information will be included in the next version of the map DVD-ROM.
VOICE GUIDANCE Symptom Voice guidance is not available. Possible cause Voice guidance is only available at certain intersections marked with In some cases, voice guidance is not available even when the vehicle should make a turn. Possible solution . This is not a malfunction. The vehicle has deviated from the suggested route. Go back to the suggested route or request route calculation again. Voice guidance is set to off. Turn on voice guidance. Route guidance is set to off. Turn on route guidance.
MEMO 10-10 Troubleshooting guide
11 Index CURRENT LOCATION MAP SCREEN Store Location page 6-5 Nearby page 4-42 Map View Plan View Birdview page 3-4 TM page 3-4 Split (Plan View) Split (Birdview Heading TM page 3-4 ) page 3-4 Change Map Scale for left page 3-20 North Up page 3-15 Heading Up page 3-15 Long Range Map View page 3-15 Birdview TM Angle page 3-17 Landmark Icons page 3-22 Store Tracking page 6-14
SCROLL LOCATION MAP SCREEN New Dest Add to Route Start page 5-3 More Routes page 5-3 Route Info page 5-4 Add Way Pt.
DESTINATION SCREEN Street Address Address Book page 4-3 Home Location page 4-20 Stored Location page 4-22 Previous Destinations page 4-24 Points of Interest page 4-28 Others Phone Number page 4-41 Nearby Places page 4-42 Previous Starting Point page 4-25 Stored Routes page 4-27 Freeway Entrance/Exit page 4-38 Intersection page 4-12 City Center page 4-8
ROUTE SCREEN Cancel Route Guidance Change/Edit Route Route Priority Route Information page 5-35 Resume Route Guidance page 5-36 Detour page 5-17 Recalculate Route page 5-18 Edit Route page 5-19 Store Current Route page 6-12 Fastest Route page 5-12 Minimize Freeway page 5-12 Shortest Route page 5-12 Detailed Route Priorities page 5-13 Turn list page 5-27 Where am I? page 7-2 Preview page 5-27 Simulation page 5-28
Guidance Settings Guidance Screen Default page 5-31 Route Guidance page 5-29 Guidance Voice page 5-29 Small Turn Arrow on Map page 5-29 Voice Announcements page 5-32 Set Average Speeds page 5-33
SETTING SCREEN Display System Settings Brightness/Contrast page 8-3 Display off page 8-4 Language/Units Clock Beep Setting Language page 8-7 Unit page 8-9 Hours page 8-10 Minutes page 8-10 Auto Adjust page 8-10 Daylight Saving Time page 8-10 Select Time Zone page 8-10 page 8-6
Navigation Landmark Icons page 3-22 Map View page 3-4 Heading page 3-15 Guidance Settings page 5-29 Address Book Stored Location page 6-16 Stored Routes page 6-25 Stored Tracking page 6-26 Avoid Area page 6-27 Delete Stored Items page 6-31
Avoid Area Settings page 6-7 Tracking Display Settings page 6-26 Nearby Places Custom Settings page 6-33 Map Scrolling Information page 3-10 Map Color Settings page 8-12 Adjust Current Location page 8-13 GPS Satellite Info page 7-3 Navigation Version page 7-4 Reset ALL navigation settings to default page 8-15 Guidance Voice page 8-2 Guidance Volume page 8-2
A About route guidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 About the map DVD-ROM . . . . . . . . . . . . . . . . . . . . . . . . 9-15 Accuracy of positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4 Adding a destination or waypoint. . . . . . . . . . . . . . . . . . . 5-5 Adding additional destinations to a route . . . . . . . . 4-47 Address book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Map symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24 Map types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Menu screen types and how to operate . . . . . . . . . . . 2-4 Menu screens and their purposes . . . . . . . . . . . . . . . . . . 2-4 Minor adjustment of the stored home and locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17 Moving a map . . . . . . . . . . . .
Printing : July 2010 (05) Publication No.: N11E 04NUU0 Printed in U.S.A.
