Installation manual

2/11
2
2.1
Characteristics (continued)
Modicon TSX Micro
automation platform 0
Discrete I/O modules
(1) Characteristics at 60 °C for 60 % I/O loading or at 30 °C for 100 % I/O loading.
(2) All outputs have fast demagnetisation circuits for electro-magnets. Discharge time of
electro-magnets < L/R.
Characteristics of solid state output modules (1)
Type of modules TSX DSZ 08T2K DMZ 28DTK DSZ 08T2 DMZ 28 DT DSZ 32T2
Number of outputs
8 12 8 12 32
Connection
HE 10 connector Screw terminal block
Nominal output values Voltage
V c 24
Current
A 0.5
Tungsten filament lamp
W 10
Limit output values Voltage
V 19…30 (possible up to 34 V, limited at 1 hour per 24 hours)
Current (for U = 30 ou 34 V)
A 0.625
Logic
Positive, current source
Leakage current at state 0
mA < 0.5 (< 2 for accidental disconnection of the 0 V module)
Residual voltage
V < 0.3 (for I = 0.5 A)
Minimum load impedance
Ω 48
Response time
(2)
From state 1
ms < 0.5
From state 0
ms < 0.5
Switching frequency on inductive load
Hz < 0.6/LI
2
Built-in protection Against overvoltages By Zener diode
Against reverse polarity
By reverse mounted diode on power supply. Provide 1 fast-blow fuse on the + c 24 V of the
preactuator supply.
Against short-circuits and
overloads
A By current limiter and thermal breaker
0.75 y Id y 2
Paralleling of outputs
2 outputs max.
Consumption
See page 6/4
Nominal dissipated power Via module
W 3.5 3.2
Via channel at 1
W 0.15
Isolation(test voltage) Between output and ground
V rms 1500 - 50/60 Hz for 1 minute
Between outputs and
internal logic
V rms 1500 - 50/60 Hz for 1 minute
Insulation resistance
MΩ > 10 at c 500 V
Type of modules TSX DSZ 04T22 TSX DMZ 16DTK TSX DMZ 64DTK
Nombre of sorties
4 8 32
Connection
Screw terminal block HE 10 connector, cage
terminal block
HE 10 connector
Nominal output values Voltage
V c 24
Current
A 2 0.5 0.1
Tungsten filament lamp
W 15 10 1.2 max.
Limit output values Voltage
V 19…30 (possible up to 34 V, limited at 1 hour per 24 hours)
Current (for U = 30 ou 34 V)
A 2.5 0.625 0.25
Logic
Positive, current emis
Leakage current at state 0
mA < 0.5 < 0.5 ( < 2 for accidental
disconnection of the 0 V
module)
< 0.1
Residual voltage
V < 0.8 (for I = 2 A) < 0.3 (for I = 500 mA) < 1.5
Minimum load impedance
Ω 12 48 220
Response time
(2)
From state 1
ms < 1 < 0.5 < 0.25
From state 0
ms < 1 < 0.5 < 0.25
Switching frequency on inductive load
Hz < 0.5/LI
2
< 0.6/LI
.
< 0.5/LI
Built-in protection Against overvoltages
By Zener diode
Against reverse polarity
By reverse mounted diode on power supply. Provide 1 fast-blow fuse on the + c 24 V of the
preactuator supply.
Against short-circuits and
overloads
A By current limiter and
elecctronic breaker
2.6 y Id y 5
By current limiter and thermal
breaker
0.75 y Id y 2
By current limiter and
elecctronic breaker
0.125 y Id y 0.185
Paralleling of outputs
2 outputs max. 3 outputs max.
Consumption
See page 6/4
Nominal dissipated power Via module
W 3.8 3 3.5
Via channel at 1
W 1.15 (U = 24 V) 0.15 < 0.7 (U = 24 V)
Isolation(test voltage) Between output and ground
V rms 1500 - 50/60 Hz for 1 minute
Between outputs and
internal logic
V rms 1500 - 50/60 Hz for 1 minute
Insulation resistance
MΩ > 10 at c 500 V
R
eferences:
p
ages 2/13 and 2/14
Connections :
Connections:
pages 2/15 to 2/17
Courtesy of Steven Engineering, Inc. ● 230 Ryan Way, South San Francisco, CA 94080-6370 ● General Inquiries: [phone] ● www.stevenengineering.com
efesotomasyon - telemecanique inverter