Use and Care Guide
NEVER use an open ame of any kind to test this smoke alarm. You might accidentally
damage or set re to the smoke alarm or to your home. The built-in test switch accurately
tests the smoke alarm’s operation as required by Underwriters Laboratories Inc. (UL).
(UTHA) Sensitivity Indicating Means
The sensitivity indicating means for this Smoke and Fire Alarm is the use of the analyzer for Smoke
Detectors Model 501-A or 501-A/Bat Aerosol Generator Manufactured by Gemini Scientic Corp.,
1122-B Aster Ave., Sunnyvale, CA 94086.
The Equivalent UL 268 Light obscuration %/Ft as measured by this instrument must be within the
obscuration listed on the back of this alarm.
(UTHA) Go/No-Go Field Test
The Go/No-Go test for this smoke and re alarm is to use one of the following UL listed can-type
aerosol smoke alarm testers. The instructions for use are printed on the canister. Home Safeguard,
Model 25S.
If you choose to use an aerosol smoke product to test the smoke alarm, be certain to use
one that has been Listed to Underwriters Laboratories, Inc. Safety Standards and use it
only as directed. Use of non-UL Listed products or improper use of UL Listed products may
affect the smoke alarm’s sensitivity.
(UTHA) MAINTENANCE:
The alarm is virtually maintenance free. However, under dusty conditions, a vacuum hose may be
used to clear the sensing chamber of dust.
Clean the alarm at least once a month to remove dust, dirt, insects or debris. Always turn off power
to alarm before cleaning. Using a soft brush or wand attachment to a vacuum cleaner, vacuum all
sides and cover of the alarm. Be sure all the vents are free of debris.
If the alarm is false alarming and cannot be restored to normal operation, the alarm should be
replaced.
WEEKLY TESTING
This alarm is designed to act as a monitor, not for use as a short-term testing device, to
perform a quick check for the presence of CO or gas. WARNING: Natural gas (methane)
is highly explosive. An attempt to test the unit by exposing it to natural gas outside of a
controlled labatory environment can produce an explosion and death. NEVER use a gas
range or an open ame of any kind to test this alarm. You might accidentally damage or set
re to the alarm or to your home. NEVER use vehicle exhaust to test the alarm! Exhaust may
cause permanent damage and voids your warranty. The built-in test switch accurately tests
the alarm operation as required by ANSI/UL2034 Standard for Safety. If, at any time, you test
the alarm and it does not perform as described, replace it immediately.
It is important to test this alarm every week to make sure it is working properly.
USING THE TEST FEATURE:
Press and release the TEST button on the alarm cover.
During testing, you will hear: 3 beeps (red LED on), 2 second pause, 3 beeps (red LED on), 6
second pause, 4 beeps (red LED on), 2 second pause, 1 beep (blue LED on).
IMPORTANT!
The Silence feature is intended to temporarily silence the alarm horn. It will not correct a Smoke,
CO or Natural Gas problem. The Gas Alarm signal cannot be silenced.
RESET: To reset the QUICK FIND
®
Alarm Origination condition, press and hold the TEST/
SILENCE button on any alarm for at least 10 seconds, or until the blue LED turns on, and
then release. Reset after each alarm. The reset feature will reset all interconnected units.
SENSOR TROUBLE/SERVICE ALARM: If the alarm chirps 3 times approx. every 20 seconds and
cannot be restored to normal operation, the alarm should be replaced immediately.
END-OF-SERVICE LIFE NOTIFICATION: A majority of home re deaths are a result of no smoke
alarms or no working smoke alarms. In addtion to the “replace by date” stamped on the back of
your alarm, your alarm contains a unique audible end-of-service life notication feature. When it
is time to replace your alarm, which is after approx. 7 years of operation from initial power up, the
alarm will sound 2 chirps approx. every 20 seconds. The green LED stays on. The alarm should
be replaced immediately. The product end-of-service life notication can be temporarily silenced
for a 10 hour period for up to 20 days. After 20 days, the warning cannot be silenced. The alarm
should be replaced immediately.
Page 12