Specifications

Universal RCP – Operation Manual
V3.1
Page 17
22/12/11
Sony Q-Ball IR
Channel 1 ID 1
Menu Selection
Main Eng Aux Setup
MASTER SETUP
Enter Password?
CAMERA TYPE
Channel 1 ID 1
Make Model
Sony Q-Ball IR
MASTER SETUP
Channel 1 ID 1
ID Assignment
Normal ID 5
RCP Panel - Master Set-up Menus
This main menu select screen can
be reached at any time by
repeated presses of the top left
menu button.
Note that if a ‘menu’ or
‘function’ button is illuminated it
will perform some action. If unlit
it will have no effect.
Before proceeding with the set-up menus a
password must be entered. This is because any
incorrect settings here may cause complete loss of
control of a particular camera. These settings
should only be made by somebody who
understands the system! The password is entered
by pressing the channel buttons in the correct
sequence.
First select the channel to be set. Now using the
left hand two function buttons scroll through the
list of available camera makes. Next select the
required camera model. Select a different
channel to set another camera type for that
channel. Note that any changes made here will
set the channel to it’s default values
This screen allows the interface box ID to be
assigned to the selected channel no. The left hand
buttons select between ‘Normal’ or ‘Multi-
Camera’ style ID’s. ‘Normal’ ID’s can be in the
range 1-8 and ‘Multi-Camera’ ID’s in the ranges
1-8, 11-18, 21-28, - up to 111-118.‘Normal’ and
‘Multi-Camera’ ID’s can be mixed for different
channels if required.
MASTER SETUP
Channel 1 ID 1
O/P Level TX Baud
4 2400
This screen allows setting of the data level
for the Audio Data O/P. Range 0-15.
Default 4 for 1v pk to pk output for a
single 600ohm load. The TX Baud rate can
be set here. Note that both these settings
apply to all channels, not just the selected
one. 9600baud can be selected which
inhibits the Audio data output and
generates an RS422 style data output.
MASTER SETUP
Channel 1 ID 1
Timing PTZF
Enabled Connected
This screen allows setting whether timing data is
sent to the camera or not. It may be necessary to
inhibit timing data if multiple RCP’s are being
used. The PTZF setting should be set to
‘Connected’ if the RCP is working into a Joystick
PTZF controller. This reduces the data rate to
allow PTZF data to be added. If the RCP is
feeding directly into a camera then set ‘Not in use’
to allow maximum data rate to be used. Both of
these settings can be set individually for each
channel.
MASTER SETUP
Channel 1 ID 1
Contrast WarnBeep
8 Disabled
This screen is used to adjust the contrast of
the LCD display. The ‘Warn Beep’ can be
enabled or disabled here. This is an
audible warning if you try to access
something which is not available and the
LCD display will show a message
describing the reason.
This screen is used to setup the 3D modes of operation. It is possible to select
either 0, 1 or 2, 3D channels. The channels are not finally set until you exit this
display using the left menu button. See the handbook for a full description of 3D
operation.
When using a keypad to control up to 96 cameras the 3D Setup will be disabled.
In most cases the RCP will auto detect a Keypad connection but if not then it can
be enabled or disabled using this menu.
MASTER SETUP
Channel 1 ID 1
3D Setup Keypad
1x3D Chan Off
This menu is only available in
‘Multi-Camera Keypad’ mode.
It is used to set the Macro Group
storage ID’s. See the ‘Multi-
camera keypad operation’ section
of the handbook
Macro Group 1
Keypad Mode ID M1
M23 3 Total 8
Add Step Full Clear