Owner’s Manual
Thank You! Thank you for purchasing the Osiris TM Pre-Programmed and Learning Remote Control. This manual is designed to assist you step-by-step as you setup the Osiris to replace all of your remote controls and automate your home entertainment system. Osiris Owner’s Manual © 2004 Universal Remote Control, Inc. The information in this manual is copyright protected. No part of this manual may be copied or reproduced in any form without prior written consent from Universal Remote Control, Inc.
Table of Contents Getting Started 2 Button Layout 3 Basic Setup 5 Pre-Programmed Method 5 Learning Method 9 Volume Control Punch Through 12 Advanced Operation 14 Advanced Setup 16 Editing Button Labels 16 Macro Button Setup 19 Favorite Channel Setup 21 Hiding and Adding Pages 23 Erasing 25 Cloning One Osiris to Another 26 Recalling Pre-Programmed Settings 27 Utilizing Optional RF Base Stations 28 IR/RF Signal Setting 31 ID # - Setting Base Station Address 33 EMITT - Setti
The Osiris Getting Started Congratulations! You’ve purchased one of the most advanced and easy to setup control systems available. The Osiris’s built-in library includes thousands of different brands and models of remote controls. In most systems, all you have to do to setup the Osiris is enter which brands and models you own. If you own a component too new to be in the library, the Osiris uses advanced learning technology to quickly set each Osiris button, one at at time.
Universal Remote Control, Inc. Button Layout Transmitting “Busy” Signal Indicator* TITLE FAVORITE CHANNEL Button LIGHT Button PAGE Buttons change the page of Display Buttons. Screen Labeled Display Buttons PAGE Numbers MAIN Button takes you to the MAIN Menu. FUNCTION Buttons *Note: When a command, macro or favorite channel is being transmitted, an icon will appear in the top right corner of the display. While the Osiris is “busy”, it will ignore a button push.
The Osiris Selecting a New DEVICE Changes All Button Commands Instantly The Osiris can operate ten different devices even though it is only one remote control. Let’s try it now! Press the MAIN button, then press the TV DEVICE button. TV DEVICE Button MAIN Button The top of the screen changes from MAIN to TV. Now all of the buttons change their function to operate a TV. Press the page buttons. Watch the labels of the display buttons change with each press.
Universal Remote Control, Inc. Basic Setup You can start setting up your Osiris using either the Pre-Programmed Method or the Learning Method. However, all the buttons of the Osiris are setup at once with the Pre-Programmed Method, so it is usually faster than the one-button-at-a-time Learning Method. Pre-Programmed Method 1 Power on the A/V component you wish to setup, so that you can test codes by sending power off commands.
The Osiris 4 Press the P-PRO button to select the Pre-Programmed Method. P-PRO Button The display changes so that you can select which Device button to setup. First Five Device Names Press a Page button to display the other five Device names. 5 In this step you choose the name of the device you’d like to setup. Use the cursor UP or DOWN buttons to change the flashing name. When it is correct, press the SELECT button.
Universal Remote Control, Inc. 6 In this step you verify the type of component you plan to operate with this device button. If the flashing name is correct, press SELECT. SELECT If the name flashing in the display is incorrect (for example, you are setting up AUX to operate a Laser Disc Player), use the UP and DOWN buttons to change the flashing name to the correct type of component. Note: Each name that appears in the display may include several types of components.
The Osiris Note: If a component fails to turn off after you have entered all of the code numbers listed for your brand, you can scan through the other brands in the table using the UP and DOWN buttons to change the code number displayed, then tapping either the Power On or Power Off buttons to see if the component powers on or off (there is a chance that your component was actually manufactured by another brand).
Universal Remote Control, Inc. 10 Repeat steps one through nine for each of your devices. If you are missing any commands, use the learning method, described next Learning Method The Osiris can learn commands from your old remote controls one-button-at-a-time by following these simple steps: 1 Line-up the Osiris with your old remote control, head-to-head, one or two inches apart. 2 On the Osiris, press and hold the MAIN and ENT (Enter) buttons at the same time for approximately three seconds.
The Osiris 4 The display will show a list of the first five devices. 5 Select the device you would like to teach commands to by pressing the Device button. Press any of the Device Buttons. 6 Now, press any button you want to teach a command to. Press any Button. Note: If you don’t see the display button you would like to teach, use the PAGE buttons. The only buttons you can’t teach are the PAGE and MAIN buttons. Once you press a button, the top of the display will change from “LEARN” to “READY”.
Universal Remote Control, Inc. 7 Press and hold the button you want on your old remote control until the display changes to either “GOOD” or “FAILED”. If the “GOOD” label appears on top of the display, you were successful. Now, press the next button you wish to teach. Keep repeating steps 6 through 7 until you have learned all the buttons you want. If the “FAILED” label appears on top of the display, try to teach the same button in Osiris once again by repeating steps 6-7.
The Osiris Volume Control Punch Through In most home entertainment systems, the sound volume is only controlled by one device. In some systems, it is the TV speakers that make the sound, so you would use the TV device on the Osiris to raise and lower the volume. In another system, it might be a surround sound receiver and speakers that control the sound, so you would use the Osiris’s AUDIO device to adjust the volume.
Universal Remote Control, Inc. 4 Press the device button for the device that doesn’t have volume control commands yet (i.e.,DVD). This is the device you are going to PUNCH TO for the volume and mute commands. Select the Device you want to “Punch To” Note: If you wish to PUNCH to the MAIN device, press the POWER OFF button at this time. 5 The bottom of the display will then flash “PUNCH FROM”. Now you select the device that has the volume commands you want (i.e.
The Osiris Advanced Operation Setting Backlight Options You can adjust the amount of time that the Osiris backlight stays on by entering the SETUP mode and proceeding to page two (using the PAGE UP button), then pressing the LIGHT button on the display (not the Backlight button). Then enter the amount of time you would like the light to stay on using the number pad (0-99 seconds). After making your selection, press the SAVE button.
Universal Remote Control, Inc. Adjusting Contrast You can make the text darker by pressing both the MAIN and cursor UP buttons at the same time. To make the text appear lighter, press both the MAIN and cursor DOWN buttons at the same time. MAIN Button Cursor Up & Down Buttons Contrast set low. Contrast set high. Transmitting (Busy Signal) Icon When a command is being transmitted, an icon will appear in the top right corner of the display.
The Osiris Advanced Setup After you’ve finished all your basic setup, you can choose to make operation easier by customizing the Osiris just the way you want, using the Advanced Setup features described in this section. Editing Button Labels You can change the name of any of the display buttons (including Favorite Channels) by following these steps: 1 Press and hold both the MAIN and ENT (Enter) buttons for approximately three seconds. The top of the display will show “SETUP”. You are in SETUP mode now.
Universal Remote Control, Inc. 5 Press the button you wish to edit. The first character of your button label blinks. Blinking Character EDIT flashes at the bottom of the screen. 6 Change the character by using any of the number keys. Each press of the same number button selects the next character of that number’s group, as shown here. A,B,C,1 J,K,L,4 S,T,U,7 D,E,F,2 M,N,O,5 V,W,X,8 G,H,I,3 P,Q,R,6 Y,Z,9 Once the character you want appears, move to the next space by pressing the RIGHT cursor button.
The Osiris 7 When you are finished editing the button, press the button you edited and “SAVED” will flash at the bottom of the display. 8 To change any other button labels on the same device, press the next button, then repeat steps 6-8. If you wish to edit a button on another device, press the MAIN button once, then repeat Steps 4-8. 9 Once you’ve finished editing buttons, press the MAIN button four times to return to normal operation.
Universal Remote Control, Inc. Macro Button Setup Imagine turning on your TV, your DVD player and your surround sound receiver by pressing a single button on your Osiris! What would normally take three remotes and three button pushes, the Osiris can accomplish with the press of one button. We call that a “Macro”.
The Osiris 5 Navigate to the Device and Page that has a button you want in your macro using the MAIN, DEVICE and PAGE buttons. Then press the button with the command you want. Whenever a button is pressed, another Macro step is counted and displayed at the bottom of the screen. Don’t worry about the number of steps. Each macro button can store up to 190 steps, so you are not likely to run out of steps! Note: You can program delays in between commands by pressing the PAUSE button.
Universal Remote Control, Inc. Favorite Channel Setup Imagine surfing all your favorite channels, without ever typing in a channel number. By simply setting up each of the favorite channel buttons, you can make TV, cable or satellite operation fun and easy. To setup a Favorite Channel button, follow these steps: 1 Enter SETUP mode by pressing and holding both MAIN and ENT for three seconds. Note: You have 30 seconds for each step, otherwise the Osiris will time out automatically.
The Osiris Note: If a number is repeated when setting the channel (for example,channel “33” or “522”) it is usually best to set a half second delay in between the identical numbers by pressing the PAUSE button. Each press of the PAUSE button increases the delay by a half second. Use the PAUSE Button to set delays between steps, each press of the pause button increases the delay by a half second. 7 Press the LIGHT button after you enter the channel number.
Universal Remote Control, Inc. Hiding and Adding Pages Each of your Osiris Devices actually contains eight pages. However, only five pages are visible in the factory default setting. Three pages are hidden in each device. If you wish to use the hidden pages, you can ADD them. If you don’t want to use some of the existing pages, you can HIDE them.
The Osiris 4 Navigate to any page, using the MAIN, DEVICE, FAV, and PAGE buttons. FAV Button DEVICE Buttons PAGE Buttons MAIN Button 5 When you select a page, the top of the screen indicates whether you want to “ADD?” or “HIDE?” the page displayed. When you would like to change a page’s visibility, press the LIGHT button. This page is hidden. To ADD it, press the LIGHT button. This page is visible. To HIDE it, press the LIGHT button.
Universal Remote Control, Inc. Erasing You can erase an individual button with a learned command, a macro or a favorite channel. You can erase an entire Device’s learned command or macro buttons. You can also erase ALL your learned commands on all devices or all your macros or favorite channels everywhere. If you really want a fresh start, it is possible to reset everything to the factory default condition.
The Osiris Erasing the Entire Osiris To erase EVERYTHING, press and hold both the MAIN and the STOP buttons for 15 seconds. After 15 seconds, the RESET screen appears. Press the SURE button to erase all of your settings and return to the factory default setup. SURE Button Cloning One Osiris to Another If you own two or more Osiris, you can copy and transfer all the setup from one Osiris to another.
Universal Remote Control, Inc. Recalling Pre-Programmed Settings If you didn’t write down the code numbers you setup your Osiris with, you can recall them via this simple process: 1 Enter SETUP mode by pressing and holding both MAIN and ENT for three seconds. Note: You have 30 seconds for each step, otherwise the Osiris will time out automatically. 2 Go to page two of the SETUP menu via the PAGE UP button. 3 Press the RECAL button. The display changes to the recall screens.
The Osiris Utilizing Optional RF Base Stations You can use the Osiris as you would your other remote controls. It transmits very powerful line-of-sight output using infrared light commands (invisible to the naked eye). When you point the Osiris at the components, expect the range to be between 30 and 50 feet. When the remote is not pointed in the general direction of the components, the range will vary (depending on reflective surfaces, lighting, etc.).
Universal Remote Control, Inc. The Osiris sends radio signal to the MRF-100, MRF-250 or the MRF-300 RF Base Stations. The RF Base Station converts radio signals to standard infrared commands and sends them out via a built-in front blaster to components in the same cabinet space. Self-adhesive “flashers” (included with the MRF-250 or the MRF-300) affix to the front panels of your components. The flashers relay infrared commands to components out-of-sight of the front blaster.
The Osiris RF Settings Overview The Osiris is factory set to work out of the box with an MRF-100 base station, which is not addressable. The only setting that affects operation with an MRF-100 is the RF/IR setting (to operate, the Osiris must be set to IR/RF or RF- it will not operate the MRF-100 in IR mode). The Osiris will operate with an MRF-250 or MRF-300 base station set to ID#0 with the factory default settings.
Universal Remote Control, Inc. 3 Press the RF button. RF Button 4 The RF Settings Menu appears. See the notes on the following pages for more info on each option. Make your selection by pressing the button you want: Signal (IR, RF or Both) Base Station ID # Emitters - ALL or a specific Emitter Blaster - Turn the Blaster On or Off Exit this Menu 5 After you’ve made a new setting and SAVED your change, use the EXIT button to return to the RF settings menu to change any other setting.
The Osiris 1 From the RF Settings Menu, select IR/RF. 2 Decide whether you are changing the Signal for all devices or just one of the devices of the Osiris. Select ALL to change the signal settings to ALL devices in the Osiris. Then, go to Step 4. Select DEVIC to change the signal settings to just one of the devices in the Osiris. Then, go to Step 3. 3 The display changes to a list of the names of your devices.
Universal Remote Control, Inc. ID # - Setting Base Station Address When you are installing a system within 100 feet of another equipment location in the same home OR near a home, condo, yacht or motor home that might potentially have an RF remote control of any kind, it is recommended that you use an addressable base station and set the address as described here. You can operate up to 15 different equipment locations, each with an MRF-250 or MRF-300 assigned a unique Receiver ID#.
The Osiris 4 Select the new setting by pressing the desired button, then press SAVE to save your new setting and return to the RF settings menu. Displays the current ID# Change the ID# to a higher number Change the ID# to a lower number Save the new setting Exit this Menu without changing the IR/RF settings EMITT - Setting IR Emitter Outputs The MRF-250 and MRF-300 Base Stations enable you to route or steer the IR commands from any Device to any or all of the IR Line Outputs.
Universal Remote Control, Inc. 3 The display changes to a list of the names of your devices. If you have two pages of devices, pressing either of the page buttons will display the other page. Select the device you would like to change the Emitter settings, then go to Step 4. Page Buttons display the other page of devices. 4 Select a device Select the new setting by pressing the desired button, then press SAVE to save your new setting and return to the RF settings menu.
The Osiris 1 From the RF Settings Menu, select BLAST. 2 Decide whether you are changing the Blaster for all devices or just one of the devices of the Osiris. Select ALL to change the blaster settings to ALL devices in the Osiris. Then, go to Step 4. Select DEVIC to change the blaster settings to just one of the devices in the Osiris. Then, go to Step 3. 3 The display changes to a list of the names of your devices.
Universal Remote Control, Inc. Pre-Programmed Code Tables The Osiris’s Pre-Programmed code library is divided into categories (TV, VCR, AUX, etc.). Each category actually includes many types of components. For example, the VCR category includes TV/VCR combo units. Within each category, the code numbers are listed in rows by brand (Sony, Panasonic, B & K, etc.). Some brands have more than one three digit code for you to try.
TV - TVs, Plasmas, Projectors and Monitors BRAND ADMIRAL ADVENT AKAI A MARK AMPRO AMSTRAD ANAM AOC APEX DIGITAL AUDIOVOX BARCO BLAUPUNKT BROKSONIC CAIRN CANDLE CAPEHART CETRONIC CITIZEN CLASSIC CONCERTO CONTEC CORONADO CRAIG CROWN CURTIS MATHES CXC DAEWOO DAYTRON DELL DREAMVISION DWIN DYNASTY DYNATECH EIKI ELECTROHOME EMERSON FISHER FUJITSU FUNAI FUTURETECH GATEWAY GE GOLDSTAR HALL MARK HITACHI HP INFINITY INFOCUS JBL JCPENNEY JENSEN JVC KEC KENWOOD KLOSS KMC CODE NUMBERS 072 081 161 160 247 197 146 248 11
TV (continued) - TVs, Plasmas, Projectors and Monitors BRAND KTV LG LODGENET LOEWE LOGIK LUXMAN LXI MAGNAVOX MARANTZ MATSUI MAXENT MEMOREX METZ MGA MINERVA MITSUBISHI MTC NAD NEC NIKEI ONKING ONWA OPTONICA OPTOMA ORION PANASONIC PHILCO PHILIPS PIONEER PORTLAND PROSCAN PROTON QUASAR RADIO SHACK RCA REALISTIC ROCTEC RUNCO SAMPO SAMSUNG SANYO SCEPTRE SCOTT SEARS SELECO SHARP SIEMENS SIGNATURE SOLE SONY SOUNDESIGN SPECTRICON SSS SUPRE MACY SYLVANIA TANDY CODE NUMBERS 043 197 143 154 113 116 102 004 106 112 119
TV (continued) - TVs, Plasmas, Projectors and Monitors BRAND TATUNG TECHNICS TECHWOOD TEKNIKA TELEFUNKEN TELERENT TERA TMK TOSHIBA TOTEVISION UNIVERSAL VIDEO CONCEPTS VIDIKRON VIDTECH VIEWSONIC WARDS WESTING HOUSE YAMAHA YORK YUPITERU ZENITH ZONDA CODE NUMBERS 056 062 034 080 004 002 003 004 024 028 043 072 101 143 037 046 086 087 072 172 004 015 138 030 007 040 062 101 143 008 009 146 174 184 188 192 004 242 004 008 009 019 028 060 061 063 064 072 074 143 164 034 076 280 197 004 004 043 073 072 095 103 15
CABLE (continued) - Cable Set Top Boxes BRAND ECHOSTAR ELECTRICORD GEMINI GENERAL ELECTRIC GENERAL INSTRUMENT GNC GOLDEN CHANNEL HAMLIN HITACHI INSIGHT JERROLD MAGNAVOX MASSILLON MEDIA ONE MEDICOM MEMOREX MITSUBISHI MOTOROLA MOVIE TIME MOXI NCTC NSC OAK PACE PANASONIC PARAGON PHILIPS PIONEER PRUCER PULSAR RCA RCN RECOTON REGAL REGENCY RODGERS SAMSUNG SCIENTIFIC ATLANTA SEREN SERVICE ELECTRIC SHAW SIGECOM SONY SPRUCER STARCOM STARGATE SUSQUEHANNA TIME WARNER TOCOM TOSHIBA UNITED CABLE UNIVERSAL VIDEOTRON VIE
DVD-DVD Players BRAND AIWA ALPINE APEX DIGITAL DENON FUNAI GE GO VIDEO HARMAN KARDON HITACHI INTEGRA JVC KENWOOD KLH KRELL LEXICON LG MAGNAVOX MARANTZ MERIDIAN MITSUBISHI MYRYAD NAD NAKAMICHI ONKYO PANASONIC PHILIPS PIONEER PROCEED PROSCAN RCA SAMSUNG SANSUI SANYO SHARP SONY SYLVANIA SYMPHONIC TATUNG THOMPSON TOSHIBA VENTURER YAMAHA ZENITH CODE NUMBERS 146 098 087 111 115 007 080 173 143 026 027 137 084 140 101 142 180 012 151 135 104 148 091 057 074 066 096 083 095 153 017 102 134 088 103 076 035 180 021
DVD-TV/DVD/VCR Combos BRAND MAGNAVOX PANASONIC SYLVANIA TOSHIBA CODE NUMBERS 143 144 143 164 DVD-DVD/VCR Combos BRAND GO VIDEO PANASONIC PHILIPS SAMSUNG SANSUI SONY TOSHIBA ZENITH CODE NUMBERS 137 150 105 (VCR Functions for VCR 067) 137 159 154 145 191 141 091 (VCR Functions for VCR171) DVD-DVD Recorders BRAND PANASONIC SONY TOSHIBA CODE NUMBERS 139 191 188 DVD-Laser Disc Players BRAND DENON FUNAI KENWOOD MAGNAVOX MARANTZ MITSUBISHI NAD OPTIMUS PANASONIC PHILIPS PIONEER RADIO SHACK RCA REALISTIC RUNCO
DVD (continued) - Laser Disc Players BRAND TOSHIBA YAMAHA CODE NUMBERS 152 106 043 129 VCR - VCRs BRAND CODE NUMBERS AIWA AKAI AMPRO ANAM AUDIO DYNAMICS BROOKSONIC CANON CAPEHART CRAIG CURTIS MATHES DAEWOO DAYTRON DBX DYNATECH ELECTROHOME EMERSON FISHER FUNAI GE GO VIDEO GOLDSTAR HARMAN KARDON HITACHI INSTANTREPLAY JCL JCPENNEY JENSEN JVC KENWOOD LG LLOYD LXI MAGIN MAGNAVOX MARANTZ MARTA MATSUI MEI MEMOREX MGA MINOLTA MITSUBISHI MTC MULTITECH NEC NORDMENDE OPTONICA 034 161 016 146 043 046 124 125 142 0
VCR - VCRs (continued) BRAND ORION PANASONIC PENTAX PHILCO PHILIPS PILOT PIONEER PORTLAND PULSAR QUARTZ QUASAR RADIO SHACK RCA REALISTIC RICO RUNCO SALORA SAMSUNG SANSUI SANYO SCOTT SEARS SHARP SHINTOM SIGNATURE SONY SOUNDESIGN STS SYLVANIA SYMPHONIC TANDY TATUNG TEAC TECHNICS TEKNIKA THOMAS TMK TOSHIBA TOTEVISION UNITECH VECTOR RESEARCH VICTOR VIDEO CONCEPTS VIDEOSONIC WARDS YAMAHA ZENITH CODE NUMBERS 025 066 070 145 083 133 140 157 163 074 167 013 020 031 063 031 034 067 031 067 034 101 054 071 156 101 0
VCR (continued) - TV/VCR Combos BRAND FUNAI GOLDSTAR HITACHI JCPENNEY LG LLOYD MAGNAVOX MEMOREX PANASONIC PHILIPS RADIO SHACK RCA SEARS SONY SYLVANIA SYMPHONIC THOMAS ZENITH CODE NUMBERS 034 101 123 034 101 101 123 034 034 067 101 070 167 034 067 123 034 101 057 154 067 034 034 034 AUDIO - Receivers, Amps, Preamps and Tuners BRAND ADC ADCOM AIWA AKAI AMC AMEND AMX ANGSTROM ANTHEM ARCAM ATLANTIC TECHNOLOGY AUDIO ACCESS AUDIO ALCHEMY AUDIO DESIGN AUDIO EASE AUDIO FILE AUDIO MATRIX AUDIO SOURCE AUDIO TECHNIC
AUDIO (continued) - Receivers, Amps, Preamps and Tuners BRAND CODE NUMBERS DELPHI DENON 415 515 002 034 109 215 229 230 027 037 234 259 330 340 341 349 350 400 401 402 444 EIGER 149 ELAN 057 290 ENLIGHTENED AUDIO 099 098 ESCIENT 368 381 451 452 453 454 FANFARE 352 FISHER 047 214 180 182 297 FLEXTRONICS 378 FOSGATE 062 231 FOSGATE AUDIONICS 342 GE 056 260 GOLDSTAR 008 HAFLER 174 HARMAN KARDON 231 233 254 153 154 118 121 227 277 317 318 365 HITACHI 020 IMERGE 371 INKEL 197 INTEGRA 354 438 JAMO 398 JBL 263
AUDIO (continued) - Receivers, Amps, Preamps and Tuners BRAND CODE NUMBERS PIONEER POLKAUDIO PROCEED RCA REALISTIC REQUEST REVOX ROTEL RUSSOUND SAMSUNG SANSUI SANYO SCOTT SEARS SHARP SHERWOOD SONY SOUNDESIGN SOUNDMATTERS SOUNDSTREAM SSI SUMO SUNFIRE TAEKWANG TEAC TECHNICS THETA DIGITAL TOSHIBA WARDS YAMAHA ZENITH 014 033 039 044 045 050 069 159 168 116 035 078 198 480 029 144 268 010 048 117 156 067 288 019 056 073 075 095 351 162 074 083 085 379 391 392 016 040 048 110 119 065 228 047 059 019 091 076 02
SAT (continued) - Satellite Receivers and DSS BRAND PANSAT PAYSAT PHILIPS PROSCAN RADIOSHACK RCA SAMSUNG SKY SONY STAR CHOICE TOSHIBA UNIDEN ZENITH CODE NUMBERS 172 136 152 153 156 068 154 136 108 117 151 106 150 148 151 106 150 123 155 163 169 175 164 103 148 127 068 154 157 158 136 159 CD - CD Changers and Players BRAND ADCOM AIWA AKAI AMC AMEND ARCAM AUDIO ACCESS AUDIO EASE AUDIO TECHNICA BSR CALIFORNIA AUDIO CAPETRONIC CARRERA CARVER CASIO CLARINETTE CREEK CROWN DENON EMERSON FISHER FRABA GENEXXA GOLD
CD (continued) - CD Changers and Players BRAND LUXMAN LXI MAGNAVOX MARANTZ MCINTOSH MCS MEMOREX MISSION MITSUBISHI MITSUMI MODULAIRE MONDIAL MYRYAD NAD NAKAMICHI NEC NIKKO NSM ONKYO OPTIMUS PANASONIC PARASOUND PHILIPS PIONEER PROCEED PROTON QUASAR RADIO SHACK RCA REALISTIC ROTEL SAE SANSUI SANYO SCOTT SHARP SHERWOOD SIGNATURE SONY SOUNDESIGN SUMO SYLVANIA SYMPHONIC TAEKWANG TANDY TEAC TECHNICS TECHWOOD THETA DIGITAL TOSHIBA VECTOR RESEARCH VICTOR WARDS YAMAHA YORX CODE NUMBERS 011 028 070 076 249 252 059 0
DVR - TiVo, Replay and other Digital Video Recorders BRAND CODE NUMBERS ECHOSTAR / DISH HUGHES JVC PHILIPS RCA REPLAY NETWORKS SONY TIVO 122 108 117 122 108 090 117 109 075 104 105 090 117 AUX - Tape Decks BRAND CODE NUMBERS AIWA CARVER DENON FISHER GOLDSTAR HARMAN KARDON JVC KENWOOD LINN LUXMAN MAGNAVOX MARANTZ MCINTOSH MITSUBISHI NAD NAKAMICHI ONKYO OPTIMUS PANASONIC PHILIPS PIONEER QUASAR SANSUI SHARP SHERWOOD SONY TEAC TECHNICS TOSHIBA VICTOR YAMAHA 015 071 100 114 006 008 027 024 036 105 227 229
AUX (continued) - Custom Installation Products BRAND AURORA MULTIMEDIA AUTON CELADON CRESTRON DELL DMX DRAPER SCREEN DREAMVISION DWIN EVERQUEST EXTRON FAROUDJA FUJI GATEWAY HP HUNTERDOUGLAS JERROLD JVC KENWOOD KEYSPAN LITE-TOUCH LUTRON MAKITA MINDPATH NILES NSM PIANO DISC PLUS POLKAUDIO RUSSOUND SCIENTIFIC ATLANTA SIMA SOLO ELECTRONICS SOMFY SONY STARCOM TURBOSCAN VELODYNE X-10 XANTECH CODE NUMBERS 220 191 221 213 214 215 216 217 218 261 262 156 204 097 080 253 206 151 184 209 261 262 261 262 219 153 185 1
The Osiris Frequently Asked Questions What is a “macro” button? It is an Osiris button you set to make a lot of things happen when you press it. For example, to watch a DVD in most home theaters requires several remote controls and many button presses (power up the TV, power up the surround sound, power up the DVD player, set the TV to the correct video input, set the surround sound to the correct audio input and finally; press play on the DVD player remote control).
Universal Remote Control, Inc. Warranty The Osiris is covered against any manufacturers defects or workmanship for a period of one year from the date of purchase if purchased from an authorized Universal Remote Control dealer. Units purchased from online auction sites or other unauthorized resellers have no warranty. This warranty does not cover the following items: - Damage from misuse, neglect, or acts of nature. - Products that have been modified or incorporated into other products.
MEMO 55
MEMO 56
MEMO 57
500 Mamaroneck Avenue, Harrison, NY 10528 Phone: (914) 835-4484 Fax: (914) 835-4532 OCE-0024B Rev.
