WALRB3P manual booklet 5/2/06 3:13 PM Page 2 TABLE OF CONTENTS Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features And Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Key Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Device Table . .
WALRB3P manual booklet 5/2/06 3:13 PM Page 3 INTRODUCTION FEATURES AND FUNCTIONS The One For All 3 Device Universal Remote Control (URC-3220) is designed to remotely operate up to three home entertainment devices. It also features intuitive and easy-to-use keys for instant control of DVD and PVR (or DVR) components. Moreover, its sophisticated technology will allow you to consolidate your original home entertainment remote controls into one easy-to-use product.
WALRB3P manual booklet 5/2/06 3:13 PM Page 5 Key Charts Use REW, PLAY, FWD, PAUSE,or STOP to control your VCR, PVR (or DVR), or DVD player. When the LED (red light) blinks, the remote control is working and (after programming) is sending signals. For a DVD player, use SKIP F. or SKIP R. to view the next or previous chapter. For a VCR, PVR (or DVR), or VOD (if available), use SCANor SCAN+ to quickly scan forward or back through a video program. Use REPLAY for an instant replay.
WALRB3P manual booklet 5/2/06 3:13 PM Page 7 INSTALLING BATTERIES PROGRAMMING DEVICE CONTROL The One For All 3 Device Universal Remote Control is preprogrammed at the factory to operate an RCA TV, a Toshiba DVD player, and a Motorola cable box. To control devices other than the default brands, perform the following steps; otherwise skip this section: 1. Turn on a desired device (e.g.,VCR or DVD player) and, if applicable, insert media (e.g., cassette or disc).
WALRB3P manual booklet 5/2/06 3:13 PM Page 9 SEARCHING FOR YOUR CODE 5. If your device does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code. 6. To check for codes of other devices, repeat steps 1 through 5 (starting on the previous page), but substitute the appropriate device key for each device you are checking.Write down the device’s code digits in the appropriate code boxes on page 8.
WALRB3P manual booklet 5/2/06 3:13 PM Page 11 PROGRAMMING A MASTER POWER MACRO (cont’d) PROGRAMMING FAVORITE CHANNEL SCAN Clearing The Master Power Macro In the CBL/SAT or TV mode, you can store a list of up to 10 favorite channels, in any order, that will be immediately scanned when FAV is pressed (see Using Channel Scan on the previous page). 1. 2. 3. Press and hold SET until the LED (red light) blinks twice, then release SET. Enter 9 - 9 - 5. The LED will blink twice. Then press POWER once.
WALRB3P manual booklet 5/2/06 3:13 PM Page 13 CHANGING VOLUME LOCK (cont’d) CLEARING CUSTOM PROGRAMMING Locking Volume Control To One Mode (Global Volume Lock) The One For All 3 Device Universal Remote Control contains an Operational Feature Reset program. If desired, you can use it to clear custom programming, except your setup codes and reassigned device keys, and reset them to original factory settings.Also see Restoring Factory Default Settings below. 2. 3.
WALRB3P manual booklet 5/2/06 3:13 PM Page 15 TROUBLESHOOTING LIFETIME WARRANTY PROBLEM: SOLUTION: Replace batteries with two new AAA alkaline batteries. PROBLEM: LED blinks when you press a key, but home entertain- One For ALL ("OFA") warrants this product to be free from defects in materials and workmanship, under normal use, throughout the period of the product’s ownership by the original purchaser.
