OCE-0024B_Rev05 2007.3.
OCE-0024B_Rev05 2007.3.9 9:35 AM 페이지2 Thank You! Thank you for purchasing the MX-350 TM Pre-Programmed and Learning Remote Control. This manual is designed to assist you step-by-step as you setup the MX-350 to replace all of your remote controls and automate your home entertainment system. MX-350 Owner’s Manual © 2004 Universal Remote Control, Inc. The information in this manual is copyright protected.
OCE-0024B_Rev05 2007.3.9 9:35 AM 페이지2 The MX-350 Getting Started Universal Remote Control, Inc. Button Layout Congratulations! Transmitting “Busy” Signal Indicator* TITLE You’ve purchased one of the most advanced and easy to setup control systems available. The MX-350’s built-in library includes thousands of different brands and models of remote controls. In most systems, all you have to do to setup the MX-350 is enter which brands and models you own.
OCE-0024B_Rev05 2007.3.9 9:35 AM 페이지4 The MX-350 Universal Remote Control, Inc. Selecting a New DEVICE Changes All Button Commands Instantly Basic Setup The MX-350 can operate ten different devices even though it is only one remote control. Let’s try it now! Press the MAIN button, then press the TV DEVICE button. TV DEVICE Button MAIN Button The top of the screen changes from MAIN to TV. Now all of the buttons change their function to operate a TV. Press the page buttons.
OCE-0024B_Rev05 2007.3.9 9:36 AM 페이지6 The MX-350 4 Universal Remote Control, Inc. Press the P-PRO button to select the Pre-Programmed Method. 6 P-PRO Button In this step you verify the type of component you plan to operate with this device button. If the flashing name is correct, press SELECT.
OCE-0024B_Rev05 2007.3.9 9:36 AM 페이지8 The MX-350 Universal Remote Control, Inc. Note: If a component fails to turn off after you have entered all of the code numbers listed for your brand, you can scan through the other brands in the table using the UP and DOWN buttons (there is a chance that your component was actually manufactured by another brand). However, most of the code tables are so large it is usually faster to use the Learning Method on Page 9.
OCE-0024B_Rev05 2007.3.9 9:36 AM 페이지10 The MX-350 Universal Remote Control, Inc. 4 The display will show a list of the first five devices. 5 Select the device you would like to teach commands to by pressing the Device button. 7 Press and hold the button you want on your old remote control until the display changes to either “GOOD” or “FAILED”. If the “GOOD” label appears on top of the display, you were successful. Now, press the next button you wish to teach.
OCE-0024B_Rev05 2007.3.9 9:36 AM 페이지12 The MX-350 Universal Remote Control, Inc. Volume Control Punch Through 4 In most home entertainment systems, the sound volume is only controlled by one device. In some systems, it is the TV speakers that make the sound, so you would use the TV device on the MX-350 to raise and lower the volume. In another system, it might be a surround sound receiver and speakers that control the sound, so you would use the MX-350’s AUDIO device to adjust the volume.
OCE-0024B_Rev05 2007.3.9 9:36 AM 페이지14 The MX-350 Universal Remote Control, Inc. Advanced Operation Adjusting Contrast Setting Backlight Options You can make the text darker by pressing both the MAIN and cursor UP buttons at the same time. To make the text appear lighter, press both the MAIN and cursor DOWN buttons at the same time.
OCE-0024B_Rev05 2007.3.9 9:36 AM 페이지16 The MX-350 Universal Remote Control, Inc. Advanced Setup 5 After you’ve finished all your basic setup, you can choose to make operation easier by customizing the MX-350 just the way you want, using the Advanced Setup features described in this section. Press the button you wish to edit. The first character of your button label blinks.
OCE-0024B_Rev05 2007.3.9 9:36 AM 페이지18 The MX-350 Universal Remote Control, Inc. 7 When you are finished editing the button, press the button you edited and “SAVED” will flash at the bottom of the display. 8 To change any other button labels on the same device, press the next button, then repeat steps 6-8. If you wish to edit a button on another device, press the MAIN button once, then repeat Steps 4-8.
OCE-0024B_Rev05 2007.3.9 9:36 AM 페이지20 The MX-350 5 Universal Remote Control, Inc. Navigate to the Device and Page that has a button you want in your macro using the MAIN, DEVICE and PAGE buttons. Then press the button with the command you want. Whenever a button is pressed, another Macro step is counted and displayed at the bottom of the screen. Don’t worry about the number of steps.
OCE-0024B_Rev05 2007.3.9 9:36 AM 페이지22 The MX-350 Note: If a number is repeated when setting the channel (for example,channel “33” or “522”) it is usually best to set a half second delay in between the identical numbers by pressing the PAUSE button. Each press of the PAUSE button increases the delay by a half second. Use the PAUSE Button to set delays between steps, each press of the pause button increases the delay by a half second. 7 Press the LIGHT button after you enter the channel number.
OCE-0024B_Rev05 2007.3.9 9:36 AM 페이지24 The MX-350 4 Universal Remote Control, Inc. Navigate to any page, using the MAIN, DEVICE, FAV, and PAGE buttons. FAV Button DEVICE Buttons PAGE Buttons MAIN Button Erasing You can erase an individual button with a learned command, a macro or a favorite channel. You can erase an entire Device’s learned command or macro buttons. You can also erase ALL your learned commands on all devices or all your macros or favorite channels everywhere.
OCE-0024B_Rev05 2007.3.9 9:36 AM 페이지26 The MX-350 Universal Remote Control, Inc. Erasing the Entire MX-350 Recalling Pre-Programmed Settings To erase EVERYTHING, press and hold both the MAIN and the STOP buttons for 15 seconds. After 15 seconds, the RESET screen appears. Press the SURE button to erase all of your settings and return to the factory default setup.
OCE-0024B_Rev05 2007.3.9 9:36 AM 페이지28 The MX-350 Utilizing Optional RF Base Stations You can use the MX-350 as you would your other remote controls. It transmits very powerful line-of-sight output using infrared light commands (invisible to the naked eye). When you point the MX-350 at the components, expect the range to be between 30 and 50 feet. When the remote is not pointed in the general direction of the components, the range will vary (depending on reflective surfaces, lighting, etc.).
OCE-0024B_Rev05 2007.3.9 9:36 AM 페이지30 The MX-350 Universal Remote Control, Inc. 3 RF Settings Overview The MX-350 is factory set to work out of the box with an MRF-100 base station, which is not addressable. The only setting that affects operation with an MRF-100 is the RF/IR setting (to operate, the MX-350 must be set to IR/RF or RF- it will not operate the MRF-100 in IR mode). The MX-350 will operate with an MRF-250 or MRF-350 base station set to ID#0 with the factory default settings.
OCE-0024B_Rev05 2007.3.9 9:37 AM 페이지32 The MX-350 Universal Remote Control, Inc. 1 From the RF Settings Menu, select IR/RF. ID # - Setting Base Station Address 2 Decide whether you are changing the Signal for all devices or just one of the devices of the MX-350.
OCE-0024B_Rev05 2007.3.9 9:37 AM 페이지34 The MX-350 4 Select the new setting by pressing the desired button, then press SAVE to save your new setting and return to the RF settings menu. Universal Remote Control, Inc. 3 Displays the current ID# Change the ID# to a higher number Page Buttons display the other page of devices.
OCE-0024B_Rev05 2007.3.9 9:37 AM 페이지36 The MX-350 Universal Remote Control, Inc. 1 From the RF Settings Menu, select BLAST. Pre-Programmed Code Tables 2 Decide whether you are changing the Blaster for all devices or just one of the devices of the MX-350. The MX-350’s Pre-Programmed code library is divided into categories (TV, VCR, AUX, etc.). Each category actually includes many types of components. For example, the VCR category includes TV/VCR combo units.
OCE-0024B_Rev05 2007.3.
OCE-0024B_Rev05 2007.3.
OCE-0024B_Rev05 2007.3.
OCE-0024B_Rev05 2007.3.
OCE-0024B_Rev05 2007.3.
OCE-0024B_Rev05 2007.3.
OCE-0024B_Rev05 2007.3.
OCE-0024B_Rev05 2007.3.
OCE-0024B_Rev05 2007.3.
OCE-0024B_Rev05 2007.3.
OCE-0024B_Rev05 2007.3.
OCE-0024B_Rev05 2007.3.9 9:37 AM 페이지60 The MX-350 Universal Remote Control, Inc. Frequently Asked Questions Warranty What is a “macro” button? The MX-350 is covered against any manufacturers defects or workmanship for a period of one year from the date of purchase if purchased from an authorized Universal Remote Control dealer. Units purchased from online auction sites or other unauthorized resellers have no warranty.
OCE-0024B_Rev05 2007.3.9 9:37 AM 페이지62 500 Mamaroneck Avenue, Harrison, NY 10528 Phone: (914) 835-4484 Fax: (914) 835-4532 OCE-0024B Rev.
