Operating instructions
Table Of Contents
- Comfort Panels
- Legal information
- Preface
- Table of contents
- 1 Overview
- 2 Safety instructions
- 3 Mounting and connecting the HMI device
- 3.1 Preparation for mounting
- 3.2 Mounting the device
- 3.3 Connecting the device
- 3.3.1 Notes on connection
- 3.3.2 Connecting the equipotential bonding circuit
- 3.3.3 Connecting the power supply
- 3.3.4 Connecting the configuration PC
- 3.3.5 Connecting the PLC
- 3.3.6 Connecting a USB device
- 3.3.7 Connecting a printer
- 3.3.8 Connecting an audio device
- 3.3.9 Switching on and testing the HMI device
- 3.3.10 Securing the cables
- 4 Commissioning the device
- 4.1 Overview
- 4.2 Using the service concept
- 4.3 Operating the device
- 4.4 Configuring the device
- 4.4.1 Reference for functions
- 4.4.2 Changing settings for operation
- 4.4.3 Changing password protection
- 4.4.4 Changing HMI device settings
- 4.4.4.1 Setting the date and time
- 4.4.4.2 Changing regional settings
- 4.4.4.3 Backup registry information
- 4.4.4.4 Changing monitor settings
- 4.4.4.5 Setting the screen saver
- 4.4.4.6 Changing the printer properties
- 4.4.4.7 Enabling sound and setting sound volume
- 4.4.4.8 Assigning sound to an event
- 4.4.4.9 Restarting the HMI device
- 4.4.4.10 Displaying information about the HMI device
- 4.4.4.11 Displaying system properties
- 4.4.4.12 Displaying memory distribution
- 4.4.5 Setting storage location
- 4.4.6 Setting the delay time
- 4.4.7 Setting the uninterruptible power supply
- 4.4.8 State of uninterruptible power supply
- 4.4.9 Enabling PROFINET services
- 4.4.10 Synchronizing the time via the time server
- 4.4.11 Changing transfer settings
- 4.4.12 Configuring network operation
- 4.4.13 Changing Internet settings
- 4.4.14 Saving to external storage device (backup)
- 4.4.15 Restoring from external storage device
- 4.4.16 Activate memory management
- 5 Commissioning a project
- 6 Operating a project
- 7 Maintenance and care
- 8 Technical specifications
- 8.1 Certificates and approvals
- 8.2 Directives and declarations
- 8.3 Dimension drawings
- 8.3.1 Dimension drawings of the FKP400 Comfort
- 8.3.2 Dimension drawings of the KP700 Comfort
- 8.3.3 Dimension drawings of the KP900 Comfort
- 8.3.4 Dimension drawings of the KP1200 Comfort
- 8.3.5 KP1500 Comfort dimension drawings
- 8.3.6 Dimension drawings of the KTP400 Comfort
- 8.3.7 Dimension drawings of the TP700 Comfort
- 8.3.8 Dimension drawings of the TP900 Comfort
- 8.3.9 Dimension drawings of the TP1200 Comfort
- 8.3.10 Dimension drawings of TP1500 Comfort
- 8.3.11 Dimension drawings of TP1900 Comfort
- 8.3.12 Dimension drawings of TP2200 Comfort
- 8.3.13 Dimensions for labeling strips
- 8.4 Technical specifications
- 8.5 Bit assignment of the direct keys
- 8.6 Description of the ports
- 8.7 Communication with PLCs
- 8.8 Scope of functions with WinCC
- A Technical Support
- B Abbreviations
- Glossary
- Index
Commissioning the device
4.2 Using the service concept
Comfort Panels
62 Operating Instructions, 03/2012, A5E03404994-02
4.2 Using the service concept
If the service concept is enabled, the HMI device stores all data necessary for the operation
on the system memory card. You can insert the system memory card into any HMI device of
the same type. After copying the data and restarting the same-type HMI device is
operational.
NOTICE
System memory card in a device of a different type
If you use the system memory card of an HMI device in an HMI device of a different type,
an error message is displayed.
In the event of service, only use a system memory card in HMI devices of the same type.
4.2.1 Enabling the service concept
Requirement
● A new SIMATIC HMI Memory Card ≥ 2 GB is available.
● The slot for the system memory card is enabled (factory state).
If required, check the setting in the Control Panel under "OP Properties", "System Card"
tab, see section "Disabling the service concept (Page 64)".
Procedure
To enable the service concept for commissioning on an HMI device, proceed as follows:
1. Switch on the power supply of the HMI device.
2. Move the safety lock into position 2.
3. Insert the memory card into the slot provided for it.
4. Push the safety switch back to the initial position.
5. Confirm the "Use system card?" prompt asking you to enable the service concept.
The data from the internal memory are copied to the system memory card.
Note
No prompt in the event of a defective system memory card
If the system memory card is defective, the "Use system card?" prompt is not displayed.
Replace the system memory card with a new SIMATIC HMI Memory Card ≥ 2 GB.
Result
The service concept is enabled. The data on the system memory card are continually
updated automatically.
See also
Changing memory cards (Page 58)