User guide

15
IOC DSKUT NonMenu Commands
(NTP 297-1001-526, Disk Maintenance Subsystem Reference Manual)
>DSKUT activates this command directory.
>DISPLAYVOLS <disk number> displays information on all
volumes in the specified disk (i.e., >DV 0).
>LISTVOL <volume name> ALL lists all files owned by a user on a
Disk Volume into the User Directory: (i.e., >
LIV D010SCR1 ALL
).
>RENAMEFL <old filename> <new filename>renames an existing file:
(i.e., >RF LOGINFO COREDATA).
>ERASEFL <filename> erases a specified file from a disk volume:
(i.e., >
EF RECORDFILE
).
>CLEARBOOT <volume name> removes boot pointer previously
assigned by SETBOOT command from the file that has the
current image file status on the volume specified by LISTVOL:
(i.e., >CB D010FCIMG).
>SETBOOT <filename> assigns current image file status, via boot
pointer to a file on the volume specified by LISTVOL:
(i.e., >
STB IMG_93_11_16
).
>SHOWBOOT <volume name> displays the current image file on the
specified volume: (i.e., >SHOWBOOT D010FCIMG).
>SHOWFL <filename> ALL displays ALL information about a
specified file name.
>
SHOWVOL <volume name> ALL
displays ALL information about a
specified volume name: (i.e., >
SV D010FCIMG ALL
).
>COPYVOLUME <volume from> <volume to> copies all files from
one volume to another (i.e., >
CV D010FCIMG D010SCR1
).
>
COPY <filename> sfdev
copies file to SFDEV
SLM DISKUT NonMenu Commands
(NTP 297-5001-540, SuperNode Patching Procedures)
>DISKUT activates this command directory.
>HELP (try >HELP <command> ) the DISKUT help command.
>
ALL
list all within defined request.
>
FULL
when used with
LISTVOLS
and
LISTFL
commands, it provides more detailed info.
>INSERTTAPE (>IT) mounts the tape cartridge.
>EJECTTAPE (>ET) demounts the tape cartridge.
>LISTVOLS (>LV) lists volumes on disk.
>
LISTFL
(>
LF
) lists files on a tape or disk.
>DELETEFL (>DDF) deletes a file on a disk volume.
>LISTBOOTFL (>LBF) lists the registered boot files.
>CLEARBOOTFL(>CBF) removes a registered boot file.
>SETBOOTFL (>SBF) adds a boot file and registers it.
>RENAMEFL (>RF) renames a file on a disk volume.
>
BACKUP
(>
BA
) creates backup copies of disk files on tape.
>RESTORE (>RE) restore disk files from backup copies on tape.
>
CLEARVOL
(>
CVOL
) clears all files on a disk volume.
>VOLINFO (>VINFO) displays info about an INSV disk volume.
>QUIT exits the DISKUT super command.
>
COPY <filename> sfdev
copies file to SFDEV
Supernode Loading Procedure
(NTP 297-YYYY-545 Recovery Procedures— PCL NTPs)
To clear/set boot file:
1. List files on SLM from which you want to load (i.e., SLM 0):
>DISKUT;LF s00danyname (Note: s00danyname is an example)
2. To clear boot file:
>CBF S00D CM ALL
>
CBF S00D MS ALL
3. Set boot file:
>SBF s00danyname<filename> CM 1 ACTIVE
>
SBF s00danyname<filename> MS 1 ACTIVE
To load front end:
From RTIF of inactive side: (Note: if JAM’d, then 'RELEASE JAM' first)
1. >\BOOT SLM0 %Optional: add “T” to load from SLM tape.
2. Wait for “waiting for activity” prompt.
From RTIF of active side:
3. >\JAM
4. >YES
Note: If loading active side, first type >\OVERRIDE from its RTIF.
After loading completes then:
5. Place test calls to ensure that call processing is working.
6. Clear all alarms.
Note: See RTIF Commands and Recovery on the next page.