User guide

151
T
I
E
R
II
S
U
P
P
O
R
T
T
O
O
L
S
ISDN Q931 Procedures for Traces on BRI and PRI
Note:
For BRI Q931, see NTP 297-2401-501
DMS-100F ISDN BRI Main-
tenance Guide and the chapter on “Protocol Analysis” using PMDEBUG.
TABLE: TRKSGRP
>pos pri2w 0
PRI2W 0 DS1SIG ISDN 10 20 87Q931 2 N STAND USER
PT_PT USER N UNEQ 30 N DEFAULT DTCI 0 11 24 64K
HDLC $ %%%% 11 is span number needed for pmdebug
>pmdebug dtci 0
PMDEBUG MODE - CONNECTING TO DTCI 0 UNIT 0
WARNING: You now have access to PM monitor....proceed with caution
LTCUP> isdncp
UP:ISdncp>
<Isprottbl, Lterm,Trmtype,Sidx, Ccbcs, ISLT_unprot, ISCall_unpr,
IS_c_te_unp, IS_T_te_unp, IS_Loop_unp, DUmp_smb, HEX_smb,
ISOptns, SSb, FSBMon, Hsg, Bradntbl, LLmsim, ISLoop, FSB,Even-
tsim, CCSim, SCp_x_gen>
UP:ISdncp>hsg
Pridump,Dchdump.
UP:Hsg>pridump
PSIDE TIMESLOT CSIDE
HSG SERVICE PORT CHNL CHNL PORT CHNL SIDX
--- ------- ---- ---- ---- ---- ---- ----
31 PRA 0 24 31 2 30 3968
30 PRA 1 24 31 3 30 3840
29 PRA ** 11 ** 24 31 11 30
3712
%%% 3712 sidx needed
28 UNA %%% is span 11 %%%
27 UNA
26 UNA
25 UNA
24 UNA
23 UNA
22 UNA
21 UNA
Continue Quit
UP:Dump>* (note: *asterisk = leave 1 level)
UP:Hsg>*
UP:ISdncp>
<Isprottbl, Lterm,Trmtype,Sidx, Ccbcs,ISLT_unprot, ISCall_unpr,
IS_c_te_unp, IS_T_te_unp, IS_Loop_unp,DUmp_smb,
HEX_smb,ISOptns, SSb,FSBMon, Hsg, Bradntbl, LLmsim,ISLoop,
FSB, Eventsim, CCSim, SCp_x_gen>
UP:ISdncp>
sidx 3712
Searching the TERM_PROT_TBL...
355 356 357 358 359 360 361 362 363 364
365 366 367 368 369 370 371 372 373 374
375 376 377 378 7052 %%%% index for llsim option select tid
Done searching.
UP:ISdncp>
llmsim
<Mon, MOFf, Options_llm>
UP:LLmsim>opt
<ININT, INMon, INOff, OUTINT, OUTMon, OUTOff, Alloff, Hex,
Verbose, SYNC, Stid, Ltid, Etid, Ramfile, SCreen, Jdm, JTd, OPt-
dump, SElect, REmove, Dlselect, DLRemove>
UP:Options_llm>select 7052
7052 has been added to the select list.
Enter Set TID to select:
UP:SElect>
The following Set TIDs are in the select list:
7052
UP:Options_llm>*
Procedure continues on the next page.